Your privacy choices: We and our partners use cookies for analytics and ads. Decline all turns them off.
Privacy Policy · Do Not Sell or Share My Personal Information
Need Help?
Call
This low-profile washplate sits at the bottom of the tub and moves the load through water for proper cleaning. Replace a stripped, cracked, or loose washplate to restore wash action and reduce noise or slippage.
Replaced basket hub assembly under agitator. Agitator would not come off so I had to cut slots in agitator with a dremel tool and use a faucet knob puller tool to pull it up off the shaft. As a result I had to replace the agitator as well. Once I got the agitator off replacing the basket hub was fairly straight forward. I also used the puller to remove the basket hub gear. Read more
Seals the coupler connection on portable dishwashers to prevent leaks at the faucet adapter. Replace when worn, cracked, or flattened to stop drips.
Replaced the coupler gasket. No leaks now. Read more
Two 5-foot nylon braided hoses connect household water supply to washer inlet valves. Replace cracked, leaking, or aging hoses to prevent water damage.
Watched u tube video. Ordered replacement water inlet valve and new hoses. Dismantled washer and replaced defective valve and installed new hoses. The repair went very easily and the washer worked perfectly as a result. Read more
Adjustable leveling foot threads into washer or dryer base to stabilize appliance on uneven floors. Replace if cracked, worn, or missing to reduce rocking.
Cushioning pad that installs between the washer lid hinge and cabinet. Replace if cracked, worn, or missing to reduce squeaks and prevent metal wear.
Removed the screws, lifted the old lid out of the hinges. Replaced the hinges, set new lid in the hinges and replaced screws. Read more
Fix a washer that won't advance through cycles, fills but won't spin, or stops mid-cycle. This timer controls wash, rinse, and spin sequences. 30-minute DIY repair.
Replaced the main timer / control. Read more
Fix a washer that won't drain or leaves standing water by replacing a failed drain pump. This assembly moves water out during drain and spin cycles.
Replaced the pump, had a plumber clean out the clogged pipe Read more
Washer won't agitate or spin? This motor stator generates the magnetic field that drives the washer motor. Restores proper agitation and spin cycles.
Inner door panel insert for front-load washer door assembly. Provides structural support and finished interior surface. Replace if cracked or damaged.
With the parts I purchased from you. Read more
Rubber washer gasket for washer fill hose connections. Replace if worn or leaking at coupler adapter. Measures 1-1/16 x 5/8 inch. Verify fit with model.
Replaced with new part ordered from store Read more
PC-144 agitator that moves and tumbles clothes during wash cycles to help loosen soil and distribute water and detergent. Replacing a worn or damaged agitator restores proper wash action and improves cleaning performance. What it does:
The splines inside the bottom agitator that are supposed to fit snug with the agitator shaft were worn down and couldn't catch the shaft anymore. I removed the entire agitator then pulled the top agitator part off of the lower agitator part. I then replaced the lower agitator with the new one I purchased and kept the old top agitator part (the top part was still in good condition and didn't need replacing, although I did replace the "agitator dogs" because they're very cheap and figured it... Read more
Contains two, six foot long braided hoses with 90 degree ends.
I had a problem with the drain pump on my Kenmore HE3 and I replaced it using a drain pump I ordered from APP. That fixed that problem but once I started running the washer I started getting a FH error code. I looked it up and found that it was a problem with the washer not filling properly. I pulled the washer out and found that one of the fill hoses had kinked when I pushed the washer back in place. There was also some writing on the hose that read "Change hose every five years". I know I had... Read more
Adjustable leveling leg screws into washer base to stabilize and level your machine on uneven floors. Replace worn, missing, or damaged legs for stability.
I replaced the drive block & leveling feet, it helped a lot but the washer still shakes a lot, I am now going to try replacing the suspension rod kit, These were the most recommended fixes to the problem.The repairs were not too hard, I wish I had a spanner wrench, I couldn't find it on the website. Read more
Fix detergent mixing in your washer's dispenser with this drawer divider. Separates compartments for detergent, softener, and bleach. Easy 5-minute fix.
Internal washer drum component that directs water flow during wash cycles. Replace if cracked, broken, loose, or catching on clothing during agitation.
By replacing 1 Read more
Right hand side. For screws use WPW10119828.
With the parts supplied from your company. The lady that took my order was good at her job. All the parts were correct and fit. I thank you for the service that recieved. Read more
Opt-Out Request Honored
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.