Maytag Washer Switch

This is the washer's water level switch that senses tub level via air pressure and provides five selectable fill settings. Replacing a failed switch restores accurate filling and lets the cycle advance properly through wash, rinse, and spin.

• Monitors air pressure from the tub to detect actual water level
• Controls the inlet valves to start/stop filling at the selected setting
• Signals the timer/control to begin agitation and advance the cycle once full
• Common symptoms: overfilling or water keeps running, stops filling too soon or won't fill, inconsistent water levels, cycle won't advance due to incorrect level detection

• Disconnect power and turn off water supply before servicing
• Access the control console; remove the selector knob/dial and panel as needed
• Note wire locations (take a photo), move the harness, and transfer the pressure hose; ensure the hose is clear and firmly seated
• Securely mount the new switch, reassemble the console/knob, restore utilities, and test each fill level

This water level pressure switch senses tub water level and signals the control to stop filling and advance the cycle. Replacing a failed switch restores proper fill shut-off and allows the washer to move to wash, drain, and spin.

• Detects water level via air pressure in the attached hose from the tub air dome
• Signals the timer/control to close inlet valves at the selected fill level
• Enables agitation and spin only when the level is appropriate or the tub is empty
• Typical symptoms of a failed switch include overfilling or underfilling, continuous filling, cycle not advancing, or no spin

• Disconnect power and turn off water supply before servicing
• Access the switch in the control console or top panel; note wire locations for reassembly
• Transfer the pressure hose and wire connectors to the new switch one at a time; ensure the hose is clear, not kinked or cracked, and fits snugly
• After installation, run a quick fill test to ensure proper shut-off and cycle progression

Fix a washer that won't fill with water or overfills with this water level pressure switch. Controls proper water amounts for each wash cycle.

Dryer won't heat or overheats on low settings? A faulty temperature selector switch prevents proper heat control. Easy DIY fix in 10-15 minutes.

Fix erratic or unresponsive cycle selections with this laundry center rotary encoder switch. Mounts behind the cycle knob to restore accurate settings.

Washer overfilling or underfilling? The water level pressure switch senses tub pressure to control fill cycles. DIY repair in 20 minutes or less.

Washer won't start or spin? A faulty lid switch prevents operation when the lid position isn't detected. Simple clip-in replacement, typically done in 10 minutes.

This replacement switch restores reliable on/off control for the specific function it serves in your appliance. A failing switch can cause that feature to stop responding or behave intermittently; replacing it brings normal operation back.

• Opens and closes the electrical circuit to the associated component when actuated
• Provides consistent, safe control of the feature it operates
• Typical failure symptoms: function won't turn on, won't turn off, or works only intermittently
• Physical clues can include a loose or sticky actuator, heat discoloration, or visible arcing damage

• Disconnect power at the breaker before servicing; allow hot surfaces to cool
• Access the switch per your model's service/parts diagram and note wire positions
• Transfer wires one at a time to the new switch; secure any mounting hardware
• Verify continuity and test operation before reassembly; replace any damaged connectors

Fix a washer that won't advance cycles or gets stuck between rinse and spin. This cycle selector switch controls washing cycle progression.

Washer won't start or shows electrical faults? A failed ground switch disrupts the safety circuit. This switch restores proper grounding for reliable operation.

Fix washer overflowing or not stopping fill cycle. This water level pressure switch senses tub water and signals control to stop filling. DIY repair.

This adjustable buzzer kit replaces a failed or noisy mini buzzer to restore audible alerts for cycles, timers and notifications. Compact design lets the appliance signal you reliably when cycles finish or need attention. What it does:

• Produces audible tones for cycle end, timers and other appliance notifications
• Replaces buzzers that are silent, intermittent, weak or emitting erratic beeps
• Helps you hear and identify completed cycles and timed alerts
• Small, mountable unit that fits behind the control panel and connects to the control board

• One adjustable buzzer kit

• Disconnect power before servicing to avoid shock risk
• Access may require removing the control panel; keep fasteners organized for reassembly
• Disconnect the buzzer wiring harness or connector before removing the old unit; connect the new buzzer the same way
• Test buzzer function with power restored before fully reassembling

If your washer overfills, underfills, or won't advance cycles, the water level pressure switch likely failed. This DIY repair restores proper filling.

Fix unresponsive or erratic cycle selection with this rotary encoder switch. Mounts behind the control knob to restore accurate cycle settings and indicators.

This replacement switch restores reliable on/off control for the matched function in your appliance. A worn or sticking switch can prevent components from powering correctly; replacing it helps bring back consistent, safe operation.

• Opens and closes an electrical circuit to control a specific component
• Actuates via a knob, button, lever, or door/lid mechanism
• Common symptoms: unit or component won't start/turn on, intermittent operation, or must press/hold to work
• Visual clues: loose actuator, heat discoloration, or burned terminals

• Disconnect power before servicing; verify no voltage with a meter
• Document wire positions; move leads to the new switch one at a time
• Secure the switch in the original orientation and ensure proper actuator alignment
• Restore power and test the controlled function for proper operation

Color: Black. Instruction sheet included.