Maytag Wire, Harness, Power Cord

This replacement wire provides a single insulated conductor for restoring a broken or damaged electrical connection in your appliance. It's a direct-fit service part for repairing wiring faults and re-establishing reliable power flow. What it does

• Replaces a damaged or frayed wire that can cause intermittent or no power to a component
• Restores a secure electrical connection to stop sparking, arcing, or poor contact
• Helps resolve symptoms like intermittent operation, components not receiving power, or visible wire damage
• Useful when insulation is melted, cut, or terminal ends are corroded

• One replacement wire as pictured

• Always disconnect power to the appliance before inspecting or replacing wiring
• Verify correct routing and secure with existing clips or fasteners to keep wire away from heat and moving parts
• Reuse or replace appropriate terminal connectors; ensure tight, corrosion-free connections

This genuine OEM wiring harness routes power and signals between components to restore reliable electrical connections in the appliance. It replaces worn, damaged, or corroded harnesses to help bring components back to normal operation. What it does:

• Links motors, switches, sensors, or control boards so the appliance can receive power and communicate between parts
• Replaces frayed, burned, or broken wiring that can cause intermittent or no operation
• Helps stop electrical arcing or poor connections that may lead to component failure or safety trips
• Restores proper circuit continuity to resolve symptoms like no power to a motor, controls not responding, or intermittent cycles

• One wiring harness

• Disconnect power (unplug or shut off breaker) before starting any work
• Match connector shapes and wire colors; route harness away from moving parts and heat sources
• Secure with existing clips or ties; avoid pulling on individual wires when connecting

This wire harness routes power and signals between the appliance's controls and components to restore electrical connections and reliable operation. It replaces damaged or frayed wiring that can cause intermittent function or no power to circuits. What it does:

• Connects control board, switches, and components so signals and power transfer correctly
• Replaces broken, burned, or corroded wiring that can cause intermittent operation or component failure
• Restores proper routing and secure connections to reduce short circuits and poor contact
• Helps resolve symptoms such as non-responsive controls, no power to parts, or erratic operation

• Disconnect power (unplug appliance or shut off breaker) before starting any work
• Observe proper wire routing and secure all retaining clips and connectors to prevent rubbing or pinching
• Match connector shapes and colors; do not force connections or modify wires

This power cord supplies mains electricity to the appliance, restoring reliable power delivery so the unit can run normally. It replaces a damaged or missing cord and restores a safe, secure connection to the household outlet. What it does

• Delivers AC power from the wall outlet to the appliance's internal wiring and controls.
• Restores operation when a frayed, cut, burned, or otherwise damaged cord prevents the appliance from powering on.
• Helps stop intermittent power or sparks caused by a compromised cord connection.
• Provides a secure connection point when installed with the appliance's strain-relief and terminal block.

• One replacement power cord as shown.

• Always disconnect power at the circuit breaker or unplug the appliance before starting work.
• Route the cord to avoid pinch points and secure it with the factory strain-relief or clamp.

This wire harness routes power and signals between appliance controls and electrical components to restore reliable operation. Replaces a damaged, frayed, or burnt harness to help eliminate intermittent or lost power to components. What it does:

• Carries electrical power and control signals between the control board and motors, switches, sensors, or heating elements
• Restores consistent electrical connections when original wiring is damaged, corroded, or pinched
• Addresses symptoms such as components not powering on, intermittent operation, blown fuses, or visible burn/damage at wiring
• Prevents shorting and arcing caused by exposed or broken conductors when replaced promptly

• One wire harness as pictured and specified by the manufacturer

• Disconnect power at the breaker or unplug the appliance before inspecting or replacing the harness
• Match connector shapes and pin counts; route harness clear of sharp edges, heat sources, and moving parts
• Use only the exact replacement harness to maintain proper connector fit and circuit protection
• If you see burned connectors, melted insulation, or a repeatedly tripped breaker, inspect related components and replace damaged parts as needed

This wire harness routes electrical connections between components to restore reliable power and signal flow. It replaces a damaged or frayed harness to reduce connection faults and intermittent operation. What it does:

• Reconnects control, power, or sensor circuits to restore normal appliance operation
• Replaces damaged, burned, or broken wires and terminals that cause intermittent power or failures
• Helps eliminate arcing, shorts, or loose-connection symptoms like no-start, no-heat, or control unresponsiveness
• Maintains factory wiring layout and terminal arrangement for correct component communication

• Disconnect power to the appliance before starting any work to avoid electric shock
• Match wire colors and terminal styles to the original harness; secure connections firmly
• Inspect connectors, clips, and mounting points; replace any damaged hardware

This wire harness assembly routes power and control signals between components so the appliance operates reliably. It replaces a damaged or worn harness to restore proper electrical connections and reduce intermittent faults. What it does:

• Provides the main connector wiring between electrical components and the control board.
• Restores lost power or control signals caused by broken, frayed, or burnt wires.
• Helps stop intermittent operation, control errors, or components that won't power on.
• Maintains secure connector fit and correct wire routing to prevent shorting.

• Always disconnect power (unplug or switch off breaker) before starting any repair.
• Handle connectors carefully; release locking tabs to avoid damage.
• Route and secure the harness following original wire paths and clips to prevent chafing.