Range Control Board

This is a relay board that controls power to the surface burner elements on an electric range or cooktop. It receives signals from the electronic oven control and switches the heating elements on and off at the correct power levels. Replace this board if your surface burners fail to heat, heat inconsistently, stay on continuously, or if you notice error codes related to the surface elements.

Oven won't bake or broil? This electronic control board manages oven functions and displays. Moderate DIY repair requires console removal.

If your range display blanks out, shows error codes like F8:E0, or doesn't respond to controls, the electronic control board likely failed. Restores normal operation.

Fix an oven that won't heat, shows error codes, or has an unresponsive display. This control board regulates heating elements and oven functions.

Fix an oven that shuts off during cooking or won't maintain temperature. This range control board monitors heat and sends power to the oven elements.

This electronic PC board is the appliance's main control, processing inputs and directing power to components so cycles run correctly. Replacing a failed board can restore normal operation when the unit is dead, won't start, or stops mid-cycle.

• Interprets user inputs and sensor feedback to execute programmed cycles
• Switches relays to power motors, valves, heaters, and other loads as required
• Manages timing, temperature, and safety logic for consistent performance
• Typical failure symptoms: no power/won't start, unresponsive or erratic controls, cycles ending prematurely, recurring error codes

• Disconnect power before servicing; verify power is off with a meter
• Use ESD protection; handle the board by the edges to avoid static damage
• Move connectors one at a time to identical positions on the new board to prevent miswiring
• Some models require service-mode setup or calibration after installation—follow your model's service documentation

This electronic oven control board governs your range's heating functions and displays the time and timer. Replacing a failed board restores reliable bake/broil operation, accurate temperature control, and a responsive clock/timer interface. What it does:

• Controls bake/broil circuits to run selected cooking modes
• Monitors the oven temperature sensor and regulates heat to the set temperature
• Drives the time-of-day and countdown timer display
• Interprets keypad inputs for mode selection and settings
• Failure symptoms can include no heat or erratic heat, a blank or flickering display, or unresponsive buttons

• One electronic control board assembly

• Disconnect power at the breaker before servicing; verify no voltage is present
• Use anti-static precautions and handle the board by its edges
• Photograph wiring and transfer connectors one at a time to the same positions
• Reuse the existing mounting hardware and any faceplate/overlay as required; set the clock after restoring power

Fix display issues, unresponsive controls, or oven overheating with this electronic control board. Manages bake/broil functions and timing display.

This oven control board manages the range's bake and broil functions, temperature regulation, and the display/timer. Replacing a failed board restores accurate heating and responsive controls so the oven starts, runs, and shuts off as expected.

• Regulates bake and broil element relays based on temperature-sensor feedback and user settings
• Powers and manages the clock, timer, and oven display interface
• Common symptoms of failure: no bake/broil heat, blank or unresponsive display, beeping or error codes, oven won't turn off, or erratic temperature
• Helps restore consistent preheating and temperature control when the existing board is faulty

• Disconnect power at the breaker before servicing; verify no power is present
• Access the board from the control panel/backguard area
• Photograph wiring, then move connectors and mounting hardware to the new board one-for-one; handle electronics by the edges to avoid ESD damage
• After reassembly, restore power and test bake and broil functions and the display/keys

If your range display is blank or buttons don't respond, this oven control board manages temperature cycles and the clock. Straightforward repair in 15 minutes.

Fix F10 or F11 error codes with this range electronic oven control board. Restores accurate temperature control and timer functions. Moderate DIY repair.

Restore reliable timekeeping and timed-cycle control with this Clock/Timer Kit. It replaces a failed clock/timer so you can set the time, run countdowns, and receive alerts as designed by the manufacturer. What it does

• Displays and keeps the appliance's current time
• Controls kitchen timer/countdown functions and audible alerts
• Interfaces with the appliance to manage timed cycles (start/stop)
• Helps resolve issues like blank or dim display, timer not advancing, drifting time, or unresponsive keys/knob

• 1 clock/timer kit assembly

• Disconnect power at the breaker before servicing; verify no voltage is present
• Access the control area; note screw locations and panel orientation
• Label or photograph wire locations; transfer connections one at a time to the new unit
• Mount securely, reassemble, restore power, and set the clock before testing timer functions

Fix F11 error codes and restore oven temperature control with this electronic control board. Repairs failed timekeeping and bake/broil functions.

Fix F9 error codes, unresponsive controls, or temperature issues. This control board manages oven functions, timers, and display. Moderate DIY repair.

This electronic oven control replaces the console control used to operate a single-convection oven, restoring user inputs and cycle selection so you can reliably set temperature, timers and cooking modes. Ideal when display, touchpad or convection functions fail. What it does:

• Replaces the oven's main user control to allow selection of bake, broil, convection and timed functions
• Restores touchpad/button input and on-screen feedback when controls are unresponsive or blank
• Helps resolve symptoms such as no display, unresponsive buttons, or inability to start bake/convect cycles
• Interfaces with oven components to relay temperature and command signals to the heating system

• One control (single-conv) as shown

• Disconnect power at the circuit breaker before starting any work to avoid shock hazard
• Handle the control assembly carefully; avoid touching circuit board components and use anti-static precautions if available
• Installation typically requires removing the oven console or back access panel and unplugging the old control connector—refer to OEM service instructions

This control display board is the appliance's user-interface module that operates the front control panel and display, giving visible status and responding to user input. Replacing it fixes display and control issues safely and simply. What it does:

• Provides the visible display and interprets button/touch inputs so the appliance responds to selections.
• Can produce unresponsive or intermittent buttons/touch controls and erratic indicator lights.
• May trigger control errors or prevent cycle selection if damaged.

• Disconnect all power before starting — turn off breaker or unplug the appliance.
• Handle the board carefully and avoid static discharge; use a grounding strap if available.
• Remove and reattach wire connectors and mounting hardware gently; note connector orientation.
• Reconnect power and verify functions before reassembling trim or covers.