Range / Cooktop / Oven Burner & Related Parts

This is the main water supply tube assembly that routes wash water from the pump to the spray system. A damaged or leaking tube can reduce spray pressure and cleaning performance or allow water to escape during a cycle.

• Directs pressurized water from the sump/pump to the spray arm/manifold
• Helps maintain proper wash pressure and coverage
• Common failure signs: weak or no spray, poor cleaning, leaks from the back/under door area, or visible cracks in the tube
• Restores correct water flow path for consistent wash results

• Unplug power and turn off water to the appliance before service
• Remove lower rack and spray arm/manifold as needed to access the tube
• Inspect and transfer any reusable clips or seals if not integral to the assembly
• Ensure all connections seat fully and test for leaks after reassembly

Surface burner crown that mounts on sealed gas burners to distribute gas through flame ports. Replace if worn, clogged, cracked, or missing.

Burner cap sits on top of the gas burner head to shape the flame and shield it from spills. Replace if cracked, broken, worn, or missing.

Burner cap for gas range cooktops. Distributes flame evenly over the burner. Replace if cracked, chipped, worn, discolored, or missing.

Converts your gas range from natural gas to liquid propane. Includes all burner orifices needed for safe LP operation. Required when switching fuel types.

Black burner cap sits on top of your gas range burner head. Replace if cracked, chipped, stained, or missing to restore your cooktop's appearance.

Natural gas burner orifice meters gas flow to range burners. Replace worn or clogged orifices for stable flame. Used for LP to natural gas conversions.

This small surface burner assembly replaces a worn or damaged top burner on your gas range or cooktop, restoring quick ignition and an even flame so the small burner heats predictably for simmering and everyday cooking.

• Distributes gas through the burner ports to create a steady, controllable flame at the small-burner position
• Works with the igniter/orifice holder to light reliably
• Common symptoms: burner won't light or only clicks, weak or uneven flame, yellow tips, delayed ignition, or flame that sputters out
• Visible cracks, warping, or heavy corrosion on the burner head

• Shut off gas supply and power; allow the cooktop to cool completely before servicing
• Remove grate and cap, then take out the old burner assembly; retain any screws or brackets as required by your model
• Align the new assembly over the orifice and igniter; seat fully and secure per the manufacturer's instructions
• Restore gas and power, then check for proper ignition and flame; verify there are no gas leaks

The burner orifice spud meters gas flow to your range's top burner. Replace worn, clogged, or incorrect orifices to restore proper flame output and combustion.

This valve-to-regulator tube carries fuel between the pressure regulator and gas control valve, maintaining a sealed path for proper ignition and stable flame. Replace if the tube is kinked, damaged, or leaking.

• Provides a rigid, factory-formed connection between the pressure regulator and valve
• Helps ensure correct gas flow to the burner system
• Failure signs include weak or no flame, delayed ignition, repeated clicking, or a gas odor
• Visible kinks, corrosion, or stripped fittings indicate the tube should be replaced

• Disconnect power and shut off the gas supply; ventilate the area before servicing
• Use two wrenches to back up fittings; avoid twisting the regulator or valve bodies
• Route the tube without kinks and tighten flare connections securely
• Leak-test all joints with an approved solution—never an open flame—before restoring service.

Replaces a damaged, missing, or incorrect LP bake burner orifice in gas ranges. Essential for propane conversion to meter gas properly to the oven.

Surface burner cap sits on top of the gas burner head to shape the flame. Replace if yours is missing, chipped, cracked, or warped for proper appearance.

The Burner Valve is an OEM component specifically designed for Frigidaire ranges. It controls gas flow to individual burners, providing a selection of different heat levels when operating the cooktop.

Causes of a bad burner valve can include wear over extended usage periods, damage from water, or gas blockage impeding operation. 

Symptoms of a bad burner valve include:

• Inability to light specific burners or adjust the flame height
• Uneven or intermittent burner performance  
• Gas leaks at burner valve connections
• Recurring error codes due to valve malfunctions

Replacing with this OEM valve restores full functionality to the range cooktop. Compatible with existing gas lines, it supports safe and reliable cooking performance.

This OEM Frigidaire replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. Replace before issues worsen.
 

Distributes gas evenly through burner ports on gas cooktops and ranges. Replace if cracked, clogged, or worn to restore uniform flame distribution.

Large. Color: Grey. It measures about 3-1/2 inches in diameter.

Controls gas flow to your range's top burner. Replace if the valve stem breaks, knob won't turn, or gas won't adjust properly for simmering or boiling.