Range / Cooktop / Oven Burner & Related Parts

This G4 orifice holder mounts beneath the cooktop to secure the burner orifice and route gas from the valve to the burner head. Replacing a damaged holder helps restore proper gas flow and consistent burner performance.

• Holds and aligns the orifice for the G4-designated surface burner
• Channels metered gas from the valve to the burner head
• Supports stable, even flame and reliable ignition at that burner
• A worn, cracked, or stripped holder may cause weak/uneven flame, delayed ignition, or a gas odor near the burner

• Disconnect power and shut off the gas supply before servicing; allow the appliance to cool
• Remove burner caps/heads and access the holder
• Transfer the existing orifice spud if reusing, or install the correct orifice specified for your gas type
• Tighten fittings to spec and leak-test all gas connections with an approved solution before restoring service

Restore reliable ignition and even oven heat. This oven burner channels gas from the safety valve and mixes air to produce an even flame across the bake area, helping your range preheat properly and maintain steady baking temperatures.

• Distributes the gas/air mixture for the bake cycle and ignites along the burner ports for a consistent flame
• Supports even heat across the oven cavity to reduce hot and cold spots while baking
• Common signs of failure: no bake flame or intermittent ignition, long preheat times, uneven baking, visible rust or holes in the burner
• Works in conjunction with the oven igniter; inspect the igniter if weak ignition persists

• Disconnect power and shut off the gas supply before servicing
• Remove oven racks, bottom panel, and flame spreader to access the burner
• Unfasten the burner, lift it off the orifice, and transfer the existing igniter and hardware to the new burner if needed
• Reinstall, ensure proper alignment over the gas orifice, restore gas/power, and verify a stable blue flame

The Burner Cap is an OEM replacement part that fits Frigidaire ranges. It is responsible for covering the small burner igniter on the cooktop. Over time, the cap can become damaged from heat exposure and food debris. Causes of failure include cracking, warping, and corrosion. 

Symptoms of a bad burner cap include:

• Uneven or abnormal flame
• Ignition issues
• Improper fit and wobbling

This burner cap is compatible with Frigidaire, Gibson, White Westinghouse, Kelvinator, and Kenmore ranges.

The Burner Base is an OEM part for Frigidaire ranges and cooktops. It serves as the mounting base and housing for the gas burners on the cooktop. Made from durable metal, the burner base ensures secure and even placement of each burner above the cooktop surface.

Causes of a bad burner base can include warping or deformation from heat exposure over time, damage from impact or mishandling, or wear and tear of the metal material.

Symptoms of a bad burner base include:

• Burners wobbling or unstable when in use
• Gas leaks around burner connections
• Difficulty lighting or uneven flames from burners
• Damage or cracks visible in the burner base

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This replacement surface burner head for gas ranges/cooktops channels fuel from the orifice into a controlled flame ring. Replace a worn or clogged head to restore reliable ignition, even flame distribution, and consistent heat control.

• Distributes gas through precision ports to create an even flame ring
• Works with the spark igniter/electrode for dependable lighting
• Supports the burner cap and stabilizes the cooking flame
• Common symptoms of a bad/clogged head: weak or uneven flames, yellow tipping, delayed ignition, or clicking without lighting

• Disconnect power and shut off gas; allow the appliance to cool before servicing
• Remove grate and burner cap; if your model uses mounting screws, remove them and lift off the old head
• Clean the orifice holder area; ensure burner ports are clear before installation
• Align the new head with the orifice and igniter, reinstall hardware and cap, then test for proper ignition and an even flame

This orifice spud meters gas flow to a burner, ensuring the correct flame size and efficient combustion. Replace a worn or damaged spud to restore proper burner performance and consistent heating.

• Controls gas flow to the burner by setting the jet opening
• Helps maintain a steady, properly sized flame
• Common fix for issues like weak, uneven, or noisy flames
• Can resolve problems after conversion or service if the original jet is damaged

• Disconnect power and shut off gas before servicing
• Allow the appliance to cool; remove burner components to access the orifice
• Use the correct size nut driver/wrench; do not overtighten
• After installation, leak-check all connections and verify proper flame

The LP Conversion Kit is an OEM part for Whirlpool gas ranges. It allows the unit to be converted from natural gas operation to liquid propane use. Included in the kit are all necessary components for a safe and proper conversion such as LP orifices, regulator, and installation instructions.

Causes of needing this conversion kit include:

• Moving to a home that only has LP gas service instead of natural gas
• Switching fuel sources to utilize less costly liquid propane

Symptoms that it may be time for an LP conversion include:

• Inability to light burners or oven due to insufficient gas pressure
• Burners or oven not heating properly on liquid propane
• Gas pressure regulator delivering too much or too little fuel

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This valve control assembly manages gas flow to the burner(s) and lets the control knob(s) start and precisely adjust the flame. Replace a worn or leaking valve assembly to restore smooth, safe flame control. What it does:

• Routes and regulates gas flow to the connected burner(s)
• Provides positive shutoff when the control is in the OFF position
• Helps address weak or no flame due to restricted flow
• Can resolve gas odor from the valve/manifold area
• Correct knobs that are hard to turn, bind, or won't fully shut off

• 1 valve control assembly

• Disconnect power and shut off the gas supply before servicing
• Remove control knobs/panels to access the assembly; note orientation and transfer any fittings as configured on your unit
• Apply approved thread sealant on NPT connections if required; tighten fittings securely without overtightening
• Leak-test all connections with soapy water or an approved detector before use; verify proper burner operation after reassembly

This LP conversion kit adapts select gas cooking appliances to operate on liquid propane. Use it when installing a natural-gas model on an LP supply to ensure proper ignition, flame characteristics, and safe performance. What it does

• Converts a natural-gas appliance for use with LP/propane per the model's installation instructions
• Provides correctly sized LP components to achieve proper flame size and combustion
• Helps prevent issues such as yellow flames, sooting, and poor simmer control caused by incorrect gas type
• Required when installing where only propane is available; model-specific kit

• One LP conversion kit

• Conversion must be performed by a qualified gas technician; follow all local codes
• Shut off gas and electrical power and allow all components to cool before servicing
• Replace the specified parts and set the pressure regulator for LP; adjust low flames/air shutters as directed in the service/installation manual
• Leak-test all connections and apply conversion labels after completion; verify flame quality

This burner head distributes gas evenly around the burner for a steady flame and reliable ignition. Replace a worn or clogged head to restore even heating, proper simmering, and consistent burner performance on your gas range or cooktop.

• Spreads gas from the orifice through ports to create an even, controlled flame ring
• Works with the burner cap and igniter/electrode for quick, consistent lighting
• Replace if ports are clogged, corroded, cracked, or warped causing uneven/yellow flames, delayed ignition, or popping
• Can help when the igniter sparks but the burner won't light or the flame won't spread

• Disconnect power and shut off gas; allow the surface to cool completely
• Remove the burner cap, then lift off the old head (some models use a retaining screw—reuse existing hardware)
• Align the new head with the orifice and igniter; seat fully and level
• Reassemble and test for proper ignition and flame; do not enlarge or clean ports with hard objects

This gas surface burner head sits on the burner base and channels gas through precision ports for quick ignition and an even flame. Replacing a worn or clogged head helps restore reliable lighting and consistent heat.

• Distributes gas from the burner base to the flame ports for even flame patterns
• Interfaces with the spark electrode to enable ignition
• Helps maintain proper flame shape and heat output
• Common symptoms include burner won't light, weak/uneven or yellow flames, delayed ignition, or continuous clicking

• Disconnect power and shut off the gas supply before servicing
• Remove grate and burner cap; lift the old burner head off the base
• Clean the burner base and electrode area; align the new head with locator pins and the electrode opening, then seat fully
• Reinstall cap and grate; restore gas/power and test ignition and flame

6,000 BTU. Color: Coal matte black. Measures about 2 inches in diameter.

This genuine replacement cap restores a clean, finished look and helps protect the underlying fastener or opening on your appliance. Replace a missing or damaged cap to keep components covered and looking factory-fresh.

• Covers and protects an exposed screw, hinge, or opening from dust and debris
• Restores the appliance's finished appearance
• Helps maintain secure retention of the underlying component
• Common signs of failure: missing or broken cap, cap won't stay in place, cosmetic wear, visible exposed fastener/opening

• Disconnect power before servicing; if working near water or gas lines, shut those off as applicable
• Gently pry off the old cap; avoid scratching surrounding surfaces
• Align and press the new cap until it seats/snaps securely

This LP broil burner orifice precisely meters propane to the oven's broiler. Replacing a damaged or incorrect orifice restores proper flame size and reliable ignition on LP fuel for consistent, efficient broiling performance.

• Regulates gas flow to the broil burner when using LP (propane) fuel
• Helps ensure correct flame size/shape for even broiling heat
• Can address weak or uneven broil flame or yellow/sooty flames
• May help resolve a broiler that won't ignite or won't stay lit

• Disconnect power and shut off the gas supply; allow the appliance to cool completely.
• Access the broil burner/orifice per the manufacturer's instructions. Remove the old orifice and hand-thread the new one; snug gently—do not overtighten.
• Restore gas and check all connections for leaks using a non-corrosive leak-detection solution; never use an open flame.
• Use only on LP systems. If converting fuel types, adjust the regulator and air shutters as specified.

This Orifice Spud precisely meters gas to a burner so you get a steady, properly sized flame. Replace a damaged, clogged, or incorrect spud to restore reliable ignition, clean flame color, and consistent heating.

• Threads into the burner's orifice holder/valve to control gas flow through a calibrated opening
• Helps maintain correct flame height and color for safe, efficient cooking
• Typical symptoms include irregular or yellow flames, weak or no flame, popping, or delayed ignition
• A clogged or worn spud can make simmer control difficult and lengthen cook times

• Shut off gas supply and power; allow the appliance to cool before service
• Remove grate, cap, and burner head (as applicable) to access the orifice; use the proper wrench or nut driver and avoid overtightening brass parts
• After reassembly, restore gas and check for leaks with soapy water; verify a steady blue flame and adjust air shutters only if directed by the manufacturer

This range burner base is a replacement part that is used for gas stovetops and ranges. This burner base directs gas to the burner head. It also holds the orifice. If this part of the range is broken or not working properly, it will not direct the gas where it needs to go. It could make it more difficult to head up the burner, and it could prove to be dangerous.While the metal pieces are durable and made to last, they may still need to be replaced. They could become dirty or corroded, or they could suffer damage when the range is moved. When replacing the burner base, owners will first want to shut off the gas supply to the stove and ensure the burner is completely cool before starting. When repairing, owners should also wear gloves to protect their hands.The burner base is compatible with many models of ranges from Whirlpool, Roper, Crosley, Estate, and Inglis. This is a genuine OEM part that has been sourced from the manufacturer. It is sold individually.