Range / Cooktop / Oven Burner & Related Parts

The Burner Valve is an OEM component specifically designed for Frigidaire ranges. It controls gas flow to individual burners, providing a selection of different heat levels when operating the cooktop.

Causes of a bad burner valve can include wear over extended usage periods, damage from water, or gas blockage impeding operation. 

Symptoms of a bad burner valve include:

• Inability to light specific burners or adjust the flame height
• Uneven or intermittent burner performance  
• Gas leaks at burner valve connections
• Recurring error codes due to valve malfunctions

Replacing with this OEM valve restores full functionality to the range cooktop. Compatible with existing gas lines, it supports safe and reliable cooking performance.

This OEM Frigidaire replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. Replace before issues worsen.
 

Replaces a damaged, missing, or incorrect LP bake burner orifice in gas ranges. Essential for propane conversion to meter gas properly to the oven.

This valve-to-regulator tube carries fuel between the pressure regulator and gas control valve, maintaining a sealed path for proper ignition and stable flame. Replace if the tube is kinked, damaged, or leaking.

• Provides a rigid, factory-formed connection between the pressure regulator and valve
• Helps ensure correct gas flow to the burner system
• Failure signs include weak or no flame, delayed ignition, repeated clicking, or a gas odor
• Visible kinks, corrosion, or stripped fittings indicate the tube should be replaced

• Disconnect power and shut off the gas supply; ventilate the area before servicing
• Use two wrenches to back up fittings; avoid twisting the regulator or valve bodies
• Route the tube without kinks and tighten flare connections securely
• Leak-test all joints with an approved solution—never an open flame—before restoring service.

Controls and stabilizes incoming gas supply to burners and oven. Replace if regulator is cracked, leaking, or fails to maintain consistent gas pressure.

Replacement surface burner for gas range cooktops. Installs directly onto the burner base. Order when your existing burner is cracked, clogged, or missing.

Pressure regulator assembly for gas ranges. Mounts to the gas supply line to control fuel pressure. Replace if cracked, leaking, or damaged.

Distributes gas evenly through burner ports on gas cooktops and ranges. Replace if cracked, clogged, or worn to restore uniform flame distribution.

Controls gas flow to your range's top burner. Replace if the valve stem breaks, knob won't turn, or gas won't adjust properly for simmering or boiling.

Black burner caps sit atop gas range burner heads to shape the flame. Replace cracked, worn, or missing caps to restore even cooking and a clean look.

This natural-gas burner orifice spud meters the correct fuel flow for a 15,000-BTU surface burner. Replacing a clogged, damaged, or wrong-size orifice restores proper flame size, cleaner combustion, and reliable cooktop performance. What it does:

• Meters gas through a calibrated opening to the burner head for correct flame height
• Sized for a 15,000-BTU surface burner using natural gas
• Installs in the orifice holder/valve body beneath the burner
• Typical symptoms of a faulty or mismatched orifice: weak/small flames, yellow/sooty flames, uneven heating, delayed ignition, burner won't reach high heat

• 1 natural-gas 15,000-BTU orifice spud

• Shut off gas supply and disconnect power; allow all burners to cool completely
• Remove grates, caps, and burner heads; lift the top or access the orifice holder as required
• Match each orifice to the correct burner location by BTU rating; do not overtighten
• After reassembly, check all connections for leaks with a non-corrosive soap solution and verify proper flame color/size

• For natural gas applications only; use the correct LP/propane orifice when converting fuel types

Surface burner cap sits on top of the gas burner head to shape the flame. Replace if yours is missing, chipped, cracked, or warped for proper appearance.

Sits under the cooktop and channels gas from the valve to the front burner head. Replace if cracked, kinked, bent, or broken from lifting the cooktop.

Replaces chipped, cracked, or missing burner cap on your gas range cooktop. This grey cap sits atop the burner base to direct and shape the flame properly.

The surface burner orifice holder is a brass or metal fitting that threads into the gas valve and holds the orifice, which is the small precisely sized opening that controls how much gas flows to a cooktop burner. Together with the orifice, it regulates flame size and ensures proper combustion. Replace this part if a burner produces an uneven, weak, or oversized flame, or if the holder is damaged, corroded, or leaking gas at the burner connection.

This is a black burner cap that sits on top of a small surface burner on a gas range. It distributes the flame evenly around the burner for consistent heating. Replace this cap if it is chipped, cracked, warped, or if you notice uneven or yellow flames on the small burner.

Replace your cracked or damaged gas range burner head assembly. This black burner head component ensures proper fit and flame distribution when installed.