Range / Cooktop / Oven Heating Element

Restore reliable baking performance with this bake heating element. Mounted at the bottom of the oven, it provides the primary heat source in Bake mode so the cavity reaches and maintains the set temperature for consistent results. What it does:

• Heats the oven in Bake mode to reach and hold the set temperature
• Failure can cause no heat in bake, very slow preheating, or uneven/undercooked results
• Visible cracks, blisters, or a broken coil indicate the element should be replaced
• A shorted element may trip a household breaker or blow a fuse

• One bake heating element

• Disconnect power at the breaker and allow the oven to cool before servicing
• Remove oven racks; take out the element's mounting screws and gently pull the element forward to access wire terminals
• Transfer wires one at a time to the new element; do not allow wires to fall back into the insulation
• Reinstall the element and panels, restore power, and test bake operation

This oven bake element is the heating element that warms the oven cavity for baking and roasting. Replacing a damaged element restores proper oven heating and helps return cooking performance to normal. What it does:

• Heats the oven interior for baking, roasting and browning.
• Replaces elements that are visibly burnt, cracked, broken, or no longer glow when the oven is on.
• Common symptoms it can fix: little or no heat from the oven, uneven cooking, or an element that sparks or shows burn spots.
• Works as the direct heater inside the oven cavity; connects to the oven terminal block.

• Disconnect power at the breaker or unplug the appliance before starting any repair.
• Access typically requires removing the oven interior panels or rear access panel; support the element while disconnecting terminals.
• Handle terminals and sharp sheet metal carefully; use insulated tools and secure terminal connections.

Warming Element

Restore reliable oven heat with this bake element. It produces the lower-oven heat during the Bake cycle, so replacing a failed element brings back normal preheat times and consistent, even results.

• Supplies primary heat from the bottom of the oven during Bake
• Common fix for: no heat on Bake, very slow preheating, uneven baking/browning
• Replace if the element is blistered, cracked, pitted, or has visible breaks
• Helps restore accurate, stable baking temperatures

• Disconnect power at the breaker or unplug the appliance before servicing
• Remove oven racks; take out the element's mounting screws to free the bracket
• Gently pull the element forward; transfer one wire at a time using insulated pliers and prevent wires from slipping back
• Re-secure the bracket/screws, ensure snug connections, restore power, and test Bake

This broil element delivers the high, direct heat the oven needs for broiling and finishing foods quickly and evenly. Replace a broken or burned element to restore upper-oven broil performance and consistent browning. What it does:

• Heats the oven's broil zone to provide the direct, high-temperature surface heat used for broiling and browning.
• Replaces a visibly broken, burned, or non-glowing element that prevents the oven from broiling.
• Helps eliminate uneven browning or lack of top-heat when the element fails.
• Works as the OEM-design replacement for compatible Whirlpool oven models when the original broil element no longer functions.

• One broil element

• Disconnect power to the appliance at the breaker before beginning any repair.
• Access typically requires removing the oven cavity racks and broil shield or the back panel to detach the element terminals.
• Handle the new element carefully and reconnect terminals securely; avoid forcing the element into place.

The Surface Element is an OEM part for Bosch cooktop and ranges. Measuring 6 inches across, it provides focused heat from below for smaller sized cookware.

Causes of a bad 6" plug-in element generally relate to normal wear and tear over time. Spills left on the coils could potentially cause issues by corroding internal wiring or damaging heating components.

Symptoms of a bad narrow surface element can include:

• The element heating intermittently or not at all
• Only parts of the coil visibly heating up
• Buzzing or clicking coming from below the element
• Tripped circuit breakers affecting that specific element

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

The Surface Element is an OEM part for Frigidaire electric ranges and cooktops. It is the individual electric coil located beneath the cooktop that provides heat.

The surface element heats up rapidly upon activation in order to boil, simmer or saute foods efficiently. Its precise heating capabilities assist home cooks in meal preparation.

Causes can be mineral deposits caked onto the element surface over time reducing its ability to transfer heat properly. Excess moisture exposure can also damage internal wiring.

Symptoms of a bad surface element include:

• Burners that do not heat up at all or heat unevenly
• Lights flickering below an element when in use
• Popping, buzzing or crackling noises coming from below an element

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This broil element is the oven's upper heating element that provides direct, high-heat cooking for broiling and browning. It restores the oven's broil function so foods brown evenly and cook from above. What it does:

• Heats the top of the oven cavity to produce direct radiant heat for broiling and browning
• Replaces a damaged, burned out, or non-heating upper oven element
• Commonly used when broil cycles fail or food doesn't brown on top
• Works with ovens that use a straight tubular broil element design

• Disconnect power to the range at the breaker or unplug before starting
• Element mounts with two screws accessible from inside the oven; handle glass and trim carefully
• Verify electrical connections are tight and correct before restoring power

Dual-zone radiant cooktop element that restores two-size heating on smooth-top electric ranges, allowing burners to match small or large cookware for more even heating and improved cooking control. What it does:

• Provides two concentric heating zones so you can use different pan sizes without losing heat where you need it.
• Heats through the ceramic glass surface using a radiant element positioned beneath the cooktop.
• Replaces a worn, damaged, or non-heating surface element to restore proper burner performance.
• Common symptoms this part can address: a burner that won't heat, partial heating (only inner or outer zone works), or visible element damage under the glass.

• Always disconnect power at the breaker before servicing to avoid electric shock.
• Handle the glass top and element carefully to avoid cracks or damage; do not operate if the glass is cracked.
• Ensure the element is fully seated and electrical terminals are secure before restoring power.

6"

This is the oven's bottom/bake heating element that provides the radiant heat used for baking and roasting. Replacing a failed element restores proper oven heating and helps return cook performance to normal. What it does:

• Heats the oven cavity during bake and roasting cycles so food reaches set temperatures.
• Failsafe indicator: oven won't reach or hold set temperature or baking is uneven.
• May show visible signs like breaks, blistering, or no glow when the oven is on.
• Restores even heating when the element is the source of the problem.

• Always disconnect power to the appliance at the breaker before starting work and allow the oven to cool completely.
• Access may require removing oven racks and the back panel or interior panel; handle the element gently to avoid damage.
• Inspect terminal connections for corrosion and tighten or replace fasteners as needed.

This bake unit is the oven's primary lower heating element that provides consistent radiant heat for baking and roasting. Replacing a worn or damaged element restores proper oven heating and helps produce even cooking results. What it does:

• Radiant-heats the oven cavity for baking and roasting
• Restores proper temperature recovery and cooking performance
• Stops issues like little or no heat, slow preheat, or uneven baking when the element is faulty
• Visible damage, breaks, or lack of glowing are common signs it needs replacement

• Disconnect power to the appliance at the breaker or unplug before servicing
• Allow the oven to cool completely before accessing the element
• Remove the faulty element by unscrewing mounting fasteners and disconnecting terminals; install the new unit in reverse order
• Verify secure electrical connections and test function after reconnecting power

This 6-inch surface coil element restores reliable heat to one burner on your electric range. Replace a burned-out or damaged coil to bring back consistent, even heating for everyday cooking.

• Provides cooking heat for a 6-inch burner position on electric ranges/cooktops
• Helps resolve a burner that won't heat or heats intermittently
• Addresses uneven heating or visible hot spots on the coil
• Replaces elements with visible breaks, blistering, or burned terminals

• Disconnect power at the breaker and allow the cooktop to cool completely before servicing
• For plug-in coil models: lift the element, pull straight out of the receptacle, and remove from the support/drip pan
• Align the new element's terminals with the receptacle, push firmly until fully seated, and set into the support
• Inspect the receptacle and wiring for heat damage and replace any compromised components before use

This 30 in. bake element is the oven's lower heating element that produces the heat needed for baking and roasting. Replace a damaged element to restore proper oven heating and even bake results. What it does:

• Heats the oven cavity from the bottom to provide baking and roasting temperatures
• Promotes even browning and consistent cooking when functioning correctly
• Common symptom: oven does not reach set temperature or won't heat at all
• Common symptom: uneven baking, cold spots, or visible breaks/burn marks on the element

• One 30 in. bake element

• Disconnect power to the appliance before starting any work
• Allow the oven to cool completely and wear gloves to protect hands from sharp edges
• Inspect and reconnect wiring securely; replace if wiring or terminals are damaged
• Follow the appliance manufacturer's instructions for removing oven racks, access panels, and securing the element

This replacement bake element heats the lower oven cavity so your range can bake and roast food at set temperatures. Restores normal baking performance when the oven isn't heating properly. What it does:

• Heats the oven's lower cavity to reach and maintain baking temperatures
• Replaces a burned-out, warped, or visibly damaged element
• Helps correct symptoms like no heat or uneven baking results
• Works with the oven control to provide consistent interior temperatures

• Disconnect power to the appliance before any service to avoid shock
• Handle element carefully; sharp edges and fragile terminals can be damaged
• Verify proper terminal connection and secure mounting during installation