Range / Cooktop / Oven Switch

This 3-speed blower switch controls the exhaust fan in your range hood, allowing you to select low, medium, or high airflow. Replacing a worn switch can restore dependable ventilation and proper speed control. What it does:

• Selects low, medium, or high fan speed by routing power to the blower motor
• Helps resolve a fan that will not run, runs only on one speed, or will not change speeds
• Can address a switch that feels loose, sticks, or works intermittently

• 1 three-speed blower switch

• Disconnect power at the breaker before servicing
• Access the control area; note wire locations (or take a photo) and transfer wires to the new switch one at a time
• Ensure push-on terminals are fully seated and secure
• Test all fan speeds before reassembly

Fix burners stuck on high or with no heat control. This infinite switch restores precise temperature adjustment. DIY-friendly repair in under an hour.

This rotary potentiometer converts shaft rotation into an electrical signal the control board can read, providing precise position feedback for user selections. Replace it if inputs become erratic, jump between settings, or the control stops responding.

• Provides rotary position feedback to the electronic control
• Enables accurate selection and adjustment of functions or setpoints
• Wear or damage can cause drifting, dead spots, or incorrect readings
• Intermittent or no response to input is a common failure symptom

• Disconnect power before servicing
• Access the control/console area to reach the component
• Note shaft orientation and any connector positions; transfer exactly to the new part
• Handle electronics with ESD care and verify smooth, full-range operation after reassembly

This potentiometer kit is the user-adjustment control the appliance reads to set operating levels. Replacing a worn potentiometer restores smooth, predictable response when you turn the knob, helping the control register settings accurately.

• Varies electrical resistance so the control can interpret knob position
• Helps set functions such as speed, power level, or temperature as designed
• Failure can present as no change when turning the knob, jumpy/erratic response, or settings stuck at one level
• Can also cause intermittent operation or "dead spots" while adjusting

• Disconnect power to the appliance before servicing
• Access the control area; note wire positions or take a photo before removal
• Transfer any knob/shaft adapter from the old part if applicable; secure the new pot without over-tightening
• Route wiring away from sharp edges and heat sources; verify proper operation before reassembly

This wiring harness connects the appliance's electrical components to restore reliable power and signal routing. It replaces a damaged or worn harness to help resolve power loss and intermittent electrical issues. What it does:

• Transfers power and control signals between components so controls and motors can operate
• Replaces frayed, burned, or broken wiring that can cause intermittent operation
• Helps stop failures that lead to no-start or loss of specific functions
• Restores secure connector fit to reduce arcing or poor connections

• Always disconnect power before servicing the appliance
• Match connectors and wire routing to the original harness; avoid stretching or pinching wires
• Secure fasteners and strain reliefs; verify all connections are fully seated
• If you find heat or burn damage at terminals, inspect adjacent components for root cause

This infinite switch controls the heat output of a surface burner element on an electric range by cycling power on and off at varying intervals. It allows you to select and maintain a specific temperature setting for the burner. Replace this switch if a burner stays on high regardless of the knob position, won't heat at all, or provides inconsistent temperatures.

Burner won't spark or ignite? This ignition switch controls the spark module for gas range surface burners. Mounts on the valve assembly behind knobs.

This infinite control switch regulates the heat output of a surface burner element on an electric range. It connects to the burner element wiring and allows you to adjust the cooking temperature from low to high. Replace this switch if a burner stays on one heat level regardless of the knob position, won't turn off, or doesn't heat at all.

Fix a dual burner that won't heat or lacks proper temperature control. This infinite switch restores heat regulation for accurate simmer-to-boil cooking.

Fix burner clicking without sparking or nonstop clicking with this valve switch. Restores spark ignition when you turn the knob to Lite. Easy DIY repair.

Replacement switch harness that connects a cooktop or range surface element switch to the appliance wiring, restoring secure electrical connections so burners heat reliably and reduce intermittent or unsafe operation. What it does:

• Carries power between the surface element (infinite) switch and the cooktop element or terminal block.
• Restores reliable heating when a damaged harness causes intermittent or no heat.
• Replaces frayed, burned, or corroded wiring that can cause arcing, sparking, or a burning smell.
• Keeps connector terminals secure to prevent loose connections and erratic element behavior.

• Disconnect all power (unplug range or shut off circuit breaker) before starting any work.
• Make secure, fully seated connections; avoid pinched or kinked wires and route harness clear of heat sources.

Fixes F1 or F2 error codes and prevents overheating in ovens. This safety switch monitors temperature limits to protect components. Direct fit part.

Burner won't spark or clicks continuously? This igniter switch restores reliable burner ignition. Simple DIY repair fixes faulty spark switches.

Color: Black. Instruction sheet included.

Oven won't start or stop correctly? A faulty micro switch prevents proper sensing of linked mechanisms. This switch restores accurate control signals.

Burner won't heat or stays on constantly? This infinite switch restores variable heat control to your cooktop element. Moderate DIY repair.