Range / Cooktop / Oven Switch
Genuine Lg part
By: Lg
Part Number: EBF60662911
This switch assembly is the door lock mechanism for select front-load washers. It detects when the door is closed and locks it during operation, allowing the washer to start and run safely without interruptions.
- Monitors door position and signals the control; failure can prevent the cycle from starting or trigger door/lock errors
- Engages the latch to secure the door during wash and spin; a bad lock may stop the cycle mid-wash
- Coordinates door unlock at cycle end; faults can delay or prevent unlocking
- Intermittent operation may cause sporadic starts or pauses
What's included: One switch assembly. Install notes:
- Disconnect power and turn off water supply before servicing
- Access the lock behind the front panel at the door opening; remove the door boot clamp to reach the mounting screws
- Move wire connectors to the new assembly one at a time to maintain placement
- Reassemble and verify proper locking and unlocking before running a full cycle
This part fixes the following symptoms
-
Doesn't shut off
-
Gas igniter glows, but will not light
See more...
Do-It-Yourself Stories from Customers like You
All the igniters spontaneously began to fire Michael S. • Adams , NY • October 12, 2019
Found a YouTube video online that provided instruction on how to change out the part.
Read more
More
$74.95
- Compare At:
-
$89.19
- You Save:
-
$14.24
Genuine Ge part
By: Ge
Part Number: WB24T10147
This high-amp SPDT switch routes power between circuits in cooking appliances to control items such as locks, element relays, or fans. Replacing a worn switch restores dependable operation and helps eliminate intermittent on/off issues. What it does:
- Single-pole, double-throw action directs power between NO/NC circuits based on actuator position
- Used to signal or control a component per the model's design (e.g., latch/lock, relay, fan)
- Failure symptoms can include no activation, stuck-on/off behavior, intermittent operation, or heat-damaged terminals
- Electrical tests may show incorrect continuity between COM–NO/NC when pressed or released
What's included:
- Includes: 1 SPDT high-amp switch
Install notes:
- Disconnect power at the breaker or unplug the appliance before servicing
- Label or photograph wiring; move leads to matching COM/NO/NC terminals on the new switch
- Mount with the correct actuator orientation and secure any bracket or screws
- Inspect connectors for heat damage; ensure tight spade fits, restore power, and test operation
Do-It-Yourself Stories from Customers like You
Faulty self cleaning latch Gregory K. • Bel Air , MD • December 28, 2016
Replaced faulty latch with new latch. New latch was different configuration, but the fit was okay. The only issue was that the wires to the electric motor were just barely long enough.
Overall easy repair if you have a T15 Torx bit, phillips screwdriver, and 1/4" nut driver. Hardest part is removing the gas cooktop to gain access to the cleaning latch. 0. Turn off electric to stove; remove the cast iron grates, center caps/orifices, and catch pans from the stovetop. 1. Disconnect the...
Read more
More
$21.95
- Compare At:
-
$26.12
- You Save:
-
$4.17
Genuine Ge part
By: Ge
Part Number: WB24X10176
Burner stuck on high or won't heat? This infinite switch controls surface element temperature from low to high. Straightforward repair restores heat control.
Do-It-Yourself Stories from Customers like You
Surface burner would only heat on high. Broken infinite switch. Philip J. • University Place , WA • March 17, 2023
We replaced the Infinite Switch.
Read more
More
$136.69
- Compare At:
-
$162.12
- You Save:
-
$25.43
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8286070
If your triple burner stays on high or won't adjust temperature, this infinite switch restores precise heat control for small, medium, and large rings.
Do-It-Yourself Stories from Customers like You
Lower front left burner would not shut off this burner is the single dual and triple element burner Maurice B. • San Diego , CA • May 07, 2015
Replace switch
Read more
More
$109.41
- Compare At:
-
$130.20
- You Save:
-
$20.79
Genuine Ge part
By: Ge
Part Number: WB24T10162
Fixes burner stuck on high, won't heat, or uneven heating. This infinite switch regulates surface element power for precise temperature control.
Do-It-Yourself Stories from Customers like You
Burner on smooth top range failed Larry E. • Port Orchard , WA • November 17, 2018
Replaced burner. Burner was shipped by FedEx overnight (my choice of shipping).
Thank you to Joy and Vincent.
Read more
More
$120.31
- Compare At:
-
$144.37
- You Save:
-
$24.06
Genuine Frigidaire part
By: Frigidaire
Part Number: 316445501
This control-panel switch restores reliable on/off control of a selected function on your range or wall oven. Replacing a worn or intermittent switch helps ensure the appliance responds consistently when you toggle that function.
- Directs power to the associated circuit when switched on or off
- Common symptoms: function won't turn on/off, intermittent operation, or the switch feels loose/sticks
- Helps restore positive, consistent control from the backguard/control panel
What's included: One switch Install notes:
- Disconnect power at the breaker before servicing
- Access the switch from the control panel/backguard; retain screws/clips
- Label/photograph wire positions and transfer leads one at a time to the new switch
- Ensure firm terminal connections, reassemble, restore power, and test operation
Do-It-Yourself Stories from Customers like You
Oven light would not turn off Stanley W. • Beaver Creek , OH • December 23, 2016
Replaced the switch
Since I was not familiar with this type of socket it would have helped to know the oven had to be pulled out of the cabinet a few inches
Read more
More
$73.95
- Compare At:
-
$87.26
- You Save:
-
$13.31
Genuine Whirlpool part
By: Whirlpool
Part Number: W11162115
Burner stuck on high or won't regulate temperature? The infinite switch controls heat levels. Common DIY repair, typically 10 minutes to install.
Do-It-Yourself Stories from Customers like You
Burner stayed on high when moved to lower heat setting David L. • Melrose , MA • December 27, 2019
I watched an 8-minute video on YouTube. Identified and ordered the part from AppliancePartsPros that a $12 shipping fee was received in 2 days. Took 10 minutes or less to install. Years ago without next-day parts and YouTube, this $60 repair would have cost me $200+.
Read more
More
$78.27
- Compare At:
-
$93.14
- You Save:
-
$14.87
Genuine Whirlpool part
By: Whirlpool
Part Number: WP9763761
If your range burner won't heat, cycles incorrectly, or buzzes when turned on, a faulty infinite switch is likely the cause. Moderately easy DIY repair.
Do-It-Yourself Stories from Customers like You
Stems were broken on handles. Knobs didn't work correctly. Dan R. • Glendale , CA • May 06, 2020
Had to replace both switches. The hard part was getting the control panel off to get access. Only a few screws but even after getting them out, really struggled getting it off. After getting off, discovered that you need to get it lifted up before pulling it off.
Read more
More
$142.95
- Compare At:
-
$170.11
- You Save:
-
$27.16
Genuine Ge part
By: Ge
Part Number: WB24K5083
Fix burners that won't spark or click constantly with this igniter switch. Mounts on the gas valve stem to activate spark ignition. Easy 15-minute repair.
Do-It-Yourself Stories from Customers like You
Clicking from ignitor mode would not stop after burner lit Jeffrey Maclachlan V. • Nederland , CO • September 03, 2017
Turned out the little switches on the knob shaft had corroded and were staying on. There was constant continuity showing with an ohm meter. Replacing the switches was very easy (always disconnect power to the unit before servicing). Bought a new ignitor module as a backup as they do go out of production after 10 years or so- another cheap and easy fix if needed in the future.
Read more
More
$25.61
- Compare At:
-
$30.48
- You Save:
-
$4.87
Genuine Bosch part
By: Bosch
Part Number: 00629722
This potentiometer is the rotary sensor behind the control knob. It converts knob rotation into an electrical signal the control board uses to adjust settings, restoring smooth, accurate response when a worn or erratic control causes inconsistent operation.
- Translates knob rotation into a variable-resistance signal for the electronic control
- Enables the control board to regulate power/heat or speed, depending on model
- Common failure symptoms: unresponsive or jumpy settings, dead spots when turning, or settings that drift
- Helps restore precise, repeatable adjustments at the knob
What's included: 1 potentiometer Install notes:
- Disconnect power to the appliance before servicing
- Pull off the knob and open the control panel to access the potentiometer
- Move wires one at a time to the new part; align the shaft/flat to the knob as noted
- Reassemble and test full range of adjustment; follow any model-specific calibration if required
Do-It-Yourself Stories from Customers like You
My dryer started showing error codes. I had the repair company come to look at the oven, they told me that the oven was not repairable. Dominick M. • Tinton Falls , NJ • December 12, 2021
I ordered all the parts from AppliancePartsPros.com and in two days I had every new part that was. Ordered. After being told from the appliance repair company that I wouldn’t get parts for months. I received all parts within 4 days, 19 different parts!
Read more
More
$63.69
- Compare At:
-
$76.43
- You Save:
-
$12.74
Genuine Whirlpool part
By: Whirlpool
Part Number: W10341820
This fan switch restores dependable control of your appliance's ventilation fan. It routes power to the blower motor so you can turn the fan on and off from the control panel when the original switch becomes worn or fails.
- Controls electrical power to the blower motor
- Restores reliable on/off fan operation from the user interface
- Typical symptoms: fan won't start, won't shut off, runs intermittently, or the switch/rocker feels loose or broken
- Contacts can wear or arc over time from repeated use
What's included: 1 fan switch Install notes:
- Disconnect power at the breaker or unplug the appliance before servicing
- Access the switch from the control panel; note wire positions and take a photo for reference
- Move wires one at a time to the matching terminals on the new switch; replace any heat-damaged connectors
- Reassemble, restore power, and test fan operation
Do-It-Yourself Stories from Customers like You
Bayanet spades were different size David M. • Leesburg , FL • September 14, 2016
Cut off old bought new spades
Read more
More
$206.44
- Compare At:
-
$243.60
- You Save:
-
$37.16
Genuine Whirlpool part
By: Whirlpool
Part Number: WP4456901
Fix sparking or non-working igniter switches with a new switch harness. Connects control switches to cooktop wiring. Moderate DIY repair, 1-2 hours.
Do-It-Yourself Stories from Customers like You
Igniter not working. Adrian H. • Totowa , NJ • January 18, 2022
Replaced the Spark Module and the Wire Harness. Works like new.
Read more
More
$117.54
- Compare At:
-
$141.05
- You Save:
-
$23.51
Genuine Whirlpool part
By: Whirlpool
Part Number: WP74011489
Fixes burner that won't heat or indicator light stuck on. This infinite switch controls surface burner power and heat settings. Moderate DIY repair.
Do-It-Yourself Stories from Customers like You
Knob twisted off Glenn M. • Aurora , OR • August 20, 2018
Replaced switch
Read more
More
$78.75
- Compare At:
-
$92.92
- You Save:
-
$14.17
Genuine Whirlpool part
By: Whirlpool
Part Number: WPY704512
If your gas burner won't light or clicks continuously, this igniter switch mounts on the valve stem to restore reliable ignition. Takes 5 minutes to replace.
Do-It-Yourself Stories from Customers like You
Front right burner would not light all other burners worked fine Kurt Z. • Austin , TX • February 06, 2015
By replacing the switch, the front right burner correctly turned on the igniter and worked. Repair took about 5 minutes. Very easy to do.
Read more
More
$64.70
- Compare At:
-
$76.99
- You Save:
-
$12.29
Genuine Frigidaire part
By: Frigidaire
Part Number: 5304528828
Fix intermittent burner failures or electrical issues with this range wiring harness. Restores power flow when connections are loose, burnt, or broken.
More
$80.95
- Compare At:
-
$95.52
- You Save:
-
$14.57
Genuine Samsung part
By: Samsung
Part Number: DG44-01003A
If your burner indicator light stays on constantly or burner runs at full heat on all settings, this infinite switch controls heat levels. 10-minute fix.
Do-It-Yourself Stories from Customers like You
Burner indicator light stays on always Joseph S. • Waldron , AR • August 02, 2015
Replaced DG44-01003A (AP4336838) Energy regulator. Fixed it with no problem.
It was the the big burner on my Samsung range that had three settings for pot size.
Read more
More
$197.95
- Compare At:
-
$237.54
- You Save:
-
$39.59