Range Parts

Stove is a GE Adora Model JBP63HH2bb. It took me forever to figure out how the burner was attached to the rails. My glass top was different than any instructions found on the internet for changing out a burner. The burners on this one are held to the bottom of the glass cook top by two rails that cross the bottom of the burner assemblies. In order to get too the burners you must remove 4 Phillips screws to lower the rails and burners from the cooktop. I suggest two people do this because... Read more

Finding the part and getting took less than three days. Installing it was simple and took only a screwdriver and 10 minutes of my time . Read more

Ordered everything from AppliancePartsPros.com and they were helpful, reliable and friendly in our interactions. Can't recommend them more for a vendor. First go get a ton of stainless steel sheet metal screws - about 20 phillips head and 20 nut driver. a drill with a phillips bit and a nutdriver bit and a zip tie and a phillips screw driver and a socket and an extension bit. Second - unplug your stove, turn off the gas valve on back of the stove and pull it away from the wall so you can... Read more

Replacement knobs ordered and came in 2 days. Read more

• Oven not heating evenly
• Little to no heat when baking

Checking for part replacement.....found your website.....I thought I had the right part, but called the tech/order line. Spoke to a very knowledgable tech, which she checked the stove serial # vs the part I thought I could use. The Tech advised that it WAS NOT and related the findings. I agreed after a short discussion and ordered the new element. The order was placed on Monday afternoon, on TUESDAY the FEDX truck pulled in with the replacement element!!!!!!! I watched the video offered on... Read more

The drip pans I ordered fit my stove perfectly. I was extremely happy. I had tried drip pans from Wal Mart and Lowe's and they wouldn't sit right in the stove. Read more

Replaced lower and upper element. Internet research suggested it was the control board. Thankfully it was a much quicker and cheaper fix. Read more

Replaced the switches. Read more

After ordering, and receiving a new Temp Sensor, I simply replaced the sensor, which was an extremely easy job, and completely resolved my problem. Read more

The most difficult part was figuring out how to take the door off as the manual instructions were not clear. Thank you, YouTube for your help. This door doesn't have the more modern release latches. You open the door all the way and stick Allen wrenches into the holes that appear by the joint of the latch. When you close the door to 3/4 or 7/8 closed, the latches are released from the unit and by holding the sides of the door, you pull it out. The whole replacement would take around an hour,... Read more

I fallow instruction by watching video Read more

• Oven is too hot
• Oven not heating evenly
• Won't start
• Little to no heat when baking

With the help of Wendee and Karen, we finally figured out my model numbers and which parts where correct. I ordered the parts and all arrived the next day except for the Broiler element which arrived in 2 days. I installed the new Baking Element myself. Took longer to figure out which curcuit braker to turn off. In about 30 minutes I had a brand new Baking Element in my oven working perfectly. On the following day, I installed the Broiler Element. That took a bit longer as it sits in a metal... Read more

• Won't start
• Element will not heat

I ordered the recommended Infinite Heat Switch Kit and Element Receptacle and Wire Kit and installed them. The latter was a breeze, appearing to be exactly the same as the original, except for the wire color. The switch, though, was another story. It is a RobertShaw "replacement" part, designed, it seems, for use in the greatest number of original units as possible. The most obvious difference between this switch and the original (besides its comparatively small size) is the long, segmented... Read more

Orded rack by stove model number. fit perfect Read more

Removed and replaced 3 door switches and mounting bar that holds switches plastic gets brittle with age and each switch comes out slightly different from each other, the chances of breaking a mounting pin is very easy. care should be taken when snapping mounting bar back into place to insure top latch and bottom latch locate properly insure bar is proper aligned when tightening screws their is free play in mounting bracket that could affect door properly engaging switches. NOTE that their are... Read more

I ordered a replacement part, which arrived in a few days. My husband removed the burned out part and put in the new one. No problems! Read more