Range Parts

I ordered the three parts listed and now my oven is beautiful, functional and like new again. I first had to figure out that the original parts are no longer available and had to perform an oven upgrade. Obviously the original design was flawed and the new design works perfectly and looks great! The whole repair cost was about $328 with shipping included. The parts were here in just a few days, about 2 to 4 days (some in two days, one in 4 days). Much cheaper and easier than replacing the... Read more

The problem seemed to be with the switch so I watched a few youtube videos to learn more about how ranges work. After locating the correct replacement switch I ordered it on-line around 10 pm Tuesday night. The new switch arrived Thursday morning at about 10 am and I had my range back up and working like new in less that 30 minutes. The hardest part was figuring out how to remove the slide in panel to access the switch. There were plastic washer/nuts behind each know which I was able to... Read more

Installed a new knob. Read more

Replaced the large burner control switches for the ones giving trouble. Since the other two switches had seen as much use as the faulty ones, replaced them too. After putting in new switches, found that one large burner had burned out so replaced it also. Range now cooks as good as new Read more

• Little to no heat when baking

I visited Appliance Pros website and indicated the problem we were having etc. Found the suspected part (heating element), went on YouTube and found out how to remove the part from the oven and test it with a multi-meter. Keep in mind I have never used a multi-meter before or made repairs to an oven before. However, I have used Appliance Pros before to fix a refrigerator problem just a month earlier and after watching their video it was a very easy repair. Anyway, I tested the old convection... Read more

The clips on the rear side of the drawer box were broken. Easy to locate the part on the website. Part in hand in two days and installed in about five minutes. Needed to remove the drawer and use a 1/4" driver, remove the broken slide and install the new one. Read more

Removed existing gasket and replaced with new gasket in less than 5 minutes. Very Easy. Make sure to remove the lower burner cover (inside the oven) which allows you to pull the end gasket material through the two circular openings in the frame. Read more

Initially, I took it off, sanded it and painted with appliance touch-up. Still didn't look good so I ordered a replacement part and installed. Read more

I ordered the infinite switch control from Appliance Parts Pro on a Wednesday afternoon and it arrived well packaged the next day even though I selected standard shipping. Thank you for the easy ordering and fast delivery! Replacing the old switch was easy: 1. Disconnect the power to the stove 2. Make sure the power is off to the stove 3. Pull 4 burner control knobs off and remove 4 large nuts attached to the 4 burner switches 4. Lift the face plate off and clean previously hidden cooking... Read more

Replaced the regulator with part #AP5802175. Watched the video when purchasing, and it was spot on. Would have taken me about 15-20 minutes if I had access to a vise, to remove one of the fittings. Was able to get it out using two wrenches, but it was not without a bit of elbow grease. The new part went in easily. Turned on valve on regulator, plugged in the power, turned on the gas valve, done. Everything worked fine. Easy job for anyone with just a few tools. Read more

Purchased a new over control board and overlay. Installed in five minutes, and everything works great now. Shipping was super fast, and was here within two days. Read more

Refer to Mynor T. of Draper, UT Aug. 12, 2018 write-up. I benefited greatly from the above write-up. It took me a little less time to perform this repair (excluding cleaning the assembly) due to the write-up. This GE Profile gas burner cook top is a “drop-in” model meant to be installed into counter top cut outs. The glass top edges are the actual support area for the entire cook top assembly. The burner bases (on top of the glass top) are screwed to the metal case enclosure (located beneath... Read more

Knowing the odds of 2 failures occurring at the same exact time was unusually high, I just searched your site for what other broken items might affect these two failures. Came up with next control item upstream and tallied that item failure with percentages of successful repairs, (4 mins.) door safety switch. Since I had to change out the most likely of the 3 and since I was already was going to be into the switch panel I ordered all 3 and swapped them all out to cover my butt, as they were... Read more

I found the model and serial #'s. Looked them up on your website. You provided a diagram with part numbers. I ordered the parts. Your website made it extremely easy. Thank you. Read more

I ordered the part from APP, removed the door, removed the inside panel and replaced the glass. Hardest part was figuring out exactly which screws to remove to open the door. Read more

• Noisy

After having replaced the drum support rollers twice in a roughly 3yr period, I realized something wasn't quite right, and indeed it wasn't. I had been ordering the wrong parts - I did use the online parts locator after checking, & double checking my model number. Apparently my older Whirlpool dryer has a somewhat ambiguous model number because the rollers that were shipped each time looked nothing like the originals. I realize that is not particularily uncommon - manufacturers often modify... Read more