By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
Need Help?
Call
Fix a burner stuck on high or not heating with this infinite control switch. Common cause when burners won't adjust temperature. DIY repair in 20 minutes.
Ordered recommended part for GE appliance. Change was very simple. Followed instructions on video and removed one wire at a time. Very easy to change 5 to 10 minutes. Read more
The Large Haliant Element is an OEM replacement part for GE ranges/cooktops. This haliant burner element is 8 inches in diameter. The element lies underneath the stovetop and will need to be replaced if it stops heating. 8-inch 2100 watt. Includes limiter Causes of a bad halogen element can include cracked or damaged ceramic material, broken support coils, or malfunctioning heating coils. Symptoms of a bad halogen element include:
This is a genuine OEM part that works for some models of GE, and Hotpoint models.
Unplug range. Open oven door to gain access to the cook top lock-down screws, located under the front edge of the cook top. Tip the cook top up and carefully remove it by pulling forward. Set aside in a safe place. Remove old, burned-out, element by removing the single lock tab, located on one of the three mounting posts, then lift up. Leave the wiring attached. Flip the element over and remove the three mounting tabs, making note of their numbered locations. Transfer the mounting tabs to... Read more
Sealed burner head for gas ranges. Sits on top of the cooktop to direct gas flow and create an even flame. Replace if cracked, corroded, or damaged.
I replaced the burner head. I turned off power to the stove, although I did not turn off the gas. I gave the old burner head a slight twist counter-clockwise until it lifted off the stove. I used the pliers to pull the wires from the old burner, then placed them onto the contacts on the new burner. Set it in place, and gave it a clockwise twist until it was snug. This stove originally came with gaskets beneath the burners, but the info for the replacement part stated that a gasket was not... Read more
Burner stuck on high heat or won't regulate temperature? This infinite switch restores precise control. Straightforward DIY repair with a screwdriver.
Replacing the oven knob sensor was easy. Figuring out it was the sensor causing the circuit breaker to trip was the challenge. Read more
Grease filter for range hoods and over-the-range microwaves. Dimensions: 5-15/16" x 13-3/8" x 3/32" (5.9375 x 13.375 x 0.09375). Rectangle shape. Captures grease from cooking air. Replace when clogged, discolored, or every 6-12 months.
Well, I gotta say I was happy to find you still had parts for almost 20 year old microwaves. The microwave itself worked fine, so I hated to have to buy a new one, but I just couldn't take being hit in the head anymore; and my fix of using string and wire to tie it to the surrounding cabinets was unsightly to say the least. I'm glad I did some research and found this part - all I had to do was pop it in place and now the vent grill is secure. Problem solved with minimal cost. Read more
Oven won't heat or takes too long to preheat? A faulty igniter is often the cause. Moderately easy DIY repair—remove panels and burner assembly.
Replaced the igniter. This was a relatively simple process. Read more
Broiler pan for ranges and ovens. Installs in main oven cavity to hold food under broiler element. Replace if cracked, warped, or heavily stained.
Fast delivery, great service Read more
Decorative overlay that covers your range control panel. Replace if cracked, peeling, worn, or warped from regular use. Protects controls and provides clear labels.
The glue behind the keypad loosened and the keypad slowly began slipping down out of place over several months. Finally, because of the movement, it warped which resulted in one of the keys being stuck. That is what gave the F12 error code. The fix was easy. I removed the control panel and then peeled off the keypad. The keypad itself then has two layers (1), the flexible circuit panel, and (2) the outward facing display. I separated the display from the circuit panel and put the new one... Read more
Clear window panel that installs in your range oven door. Replace when cracked, shattered, hazed, or missing to restore visibility and protection.
Ordered a new door through your company and replaced door on oven and it looks and works great ! Read more
The Flame Sensor is an OEM part for GE dryers. This part detects the presence of a flame in gas dryers, ensuring that the gas ignites properly for safe and efficient drying. Causes of a bad flame sensor can include regular wear and tear, carbon buildup from the gas flame, or electrical malfunctions. Symptoms of a bad flame sensor include:
This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.
GE Gas Dryer Model DBVH512GF1WW began to heat for only a short amount of time so drying clothes took WAY too long. Read online that the first thing to replace are the solenoids. Bought the two solenoids from AppliancePartsPros.com for about $50 total, and it seems to have fixed the problem. Had to watch a few videos to learn to disassemble the dryer, and the job took a couple of hours, but now that I know what I'm doing it could be done in less than 30 minutes. Also, the old solenoids tested... Read more
Range burner not heating or heating unevenly? This 8-inch surface element restores proper cooking heat. Easy DIY installation in under 15 minutes.
Replace burner and receptacle. The product arrived promptly after order and the receptacle came in a factory Whirlpool bag, indicating it was a genuine Whirlpool part. The burner did not have such identification, but works very good. I've placed 3 orders with these folks for various broken appliances, and each one has worked as advertised and performs like new. Read more
This is the main display control board for a range, housing the electronic circuitry that operates the oven's display panel, clock, and user input controls. It processes your temperature and cooking mode selections and relays commands to other components. Replace this board if the display is blank, flickering, showing error codes, or if the oven does not respond to control panel inputs.
Replaced display board Read more
Holds the gas orifice in place at the front burner on gas ranges. Replace if cracked, broken, or kinked from repeated lifting of the cooktop.
Once I watched the video on your site about gas line install, it became apparent why the line bent when I raised the lid.. also discovered those two rods have nest to go into and the lid/top now sets down tight as designed ( and as an added bonus, gas smell disappeared during oven use) I ordered the gas lines with the model number, ordered all four …. it was a bit of a chore one came up when site opened I picked it, but did not know if it was the RH or LH etc.. so reading some of your answers... Read more
This is a white oven door handle that mounts to the front of the oven door. It provides a grip for opening and closing the oven door during use. Replace this handle if it is cracked, broken, discolored, or if the mounting points have become loose or stripped, making the door difficult to open safely.
Replaced with new part Read more
Dryer door won't stay closed? The door strike secures the door latch during operation. Quick DIY fix—installs from the front in minutes.
My dryer door would not stay shut because the door strike was stuck in the door catch. I was afraid that when I pulled the strike out, it would damage the catch, so I ordered the door strike and door catch. I got the damaged door strike out with needle nosed pliers in about 15 seconds. The door catch was in perfect condition so I didn't need to use the one I ordered. So then I proceeded to install the new door strike. That took me about 15 minutes because I did not have the manual strength to... Read more
Oven not heating or reaching temperature? This bake heating element distributes even heat for proper baking. DIY-friendly repair with basic tools.
Easy fix. Both elements replaced while I was at it, so all new. Figured if one went the other was going to follow. CIRCUIT BREAKER OFF. Removed the back metal panel with my nut driver for the hex head screws. Note where the panel may slip under tabs for support. Remove slip on electrical connections on upper and lower elements. May need a pliers. (I did not want to just pull the element and the wires into the oven with the element and remove them there, like a technician would do. After 15... Read more
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.