Range Parts

• Element will not heat
• Won't start

I ORDER THE TERMINAL BLOCK KIT, AND FOLLOW THE VIDEO HOW TO REPAIRE. IT IS VERY EASY.IT TOOK ME 10 MIN. Read more

I replaced the Oven Igniter. After ensuring that it was the igniter, by turning on the stove and taking out the oven bottom. Watch if it turns red. If not, then either the wiring is faulty, or the igniter went bad. The bulb was due to a loose and broken light bulb, can't use any normal bulb, these ones are specially made to withstand the heat. And the oven bottom was warped due repeatedly heating up and cooling down over the years. It took a fair bit of time to get the new one in, since it was... Read more

• Oven not heating evenly
• Little to no heat when baking
• Element will not heat

I googled the model number of the oven and came across AppliancePartsPros.com The coil along with replacing video was right at hand. I ordered the part, got it three days later (standard shipping) and installed it. To sum it up, it was a five minute job. Read more

• Little to no heat when baking
• Oven not heating evenly

Watched the appliancepartspro video and changed it out. It took about 15 minutes. I'm sure I saved hundreds. Read more

• Won't start

There are hex screws keeping the igniter in place. I think they were 5/16...so you have to have a socket wrench. The space is kind of tight, and it's all on the right side, so if you're left handed (like I am) it's going to be a challenge to get the hex screws out without dropping them. Dropping them isn't too bad if they don't fall into the hole the gas pipe is coming through. Unfortunately one of them fell in there, and there's no getting it out of there. I had a machine screw that fit, so I... Read more

• Door won't close
• Door stuck closed

This was much easier than expected. I called Appliance Parts Pros with my model # and you told me what part I needed. It was shipped the same day and arrived the next day. I removed the inner door trim with a table knife ( don't rush this or you might crack the trim ). I then unhooked the old door latch disconnected the spring from the door hooked on the spring from the new latch and clipped in the latch to the door. Final step was to reattach the door trim. It was very easy and all I used... Read more

• Doesn't shut off
• No heat
• Won't start

The first symptom was our microwave would continue to run after the time was up. The light would go out, the turn table would stop but you could still hear the microwave running and whatever was in it would continue to cook. The only way to stop it was to open the door. It was intermittent at first but eventually it would always run no matter what as long as the door was closed. Several other posts referenced these switches as the problem. I just replaced both and problem gone. It turns out... Read more

• Element will not heat

Replaced all four element switches. Switches arrived within two days of ordering. That's about normal for AppliancePartsPros. They were the correct ones; not generic, and fit the original control knobs perfectly. This kind of service is what I'm used to from ApplicanePartsPros. Read more

• Element will not heat

Personally I have experience working with electricity and knowing if I bought the part required this would be an easy fix. I got my model number and contacted Appliance Parts Pros and placed my order for the new elements, terminal blocks, and for appearance purposes 4 new Drip Pans. Excellent service and quick shipping. I ordered my parts on Sunday and received them on Tuesday. This was a simple repair that only required a screwdriver to remove the old terminal block from the range hood, wire... Read more

Originally the dryer was squeaking a lot, so I purchased a new belt tensioner, but the original tensioner was an old-style no wheel tensioner, so that wasn't the source of the squeaking. I saw a lot of lint had built up inside the unit where there shouldn't have been that much. So I viewed a few videos on the Appliance Pros site and saw that the rear wheel guides were the cause of the squeaking and the rear felt drum and blower housing seal needed to be replaced. The rear blower housing was... Read more

I was able to remove the culprit part and replace it with a new one. Tested the unit for normal operation unit is working properly. Read more

• Little to no heat when broiling

DISCONNECT CIRCUIT BREAKER!!!. Remove oven door. Remove two screws that attach the element to the back of the oven, and two screws that secure element to the oven roof, then remove element. Had to be careful that the four wires don't slip into the back of the oven (difficult) to keep them from falling back as they are very short. Remove and replace element. I should have also detached the temp probe as it gets in the way and is easily broken off its flimsy mounting plate. The hardest part is... Read more

• Oven is too hot
• Little to no heat when baking

In the middle of Christmas baking, I noticed that it was taking a really long time to bake bread. Since I had already done 5 batches and the timing was always the same, I knew when I had to add 20 min, something was wrong. My oven thermometer (I bought at target) no longer worked so it was hard to tell the exact temperature. First, I went and bought a new thermometer to see the actual temp, then I set the oven to 350 degrees and checked to see what the thermometer was showing. It was almost 50... Read more

• Element will not heat

Burners were an exact match for the originals and the pans fit perfectly. Vastly improved the appearance of an old cook top and allowed us to to not have to replace it before our home goes up for sale. Read more

I first felt along each heating element (bake and broil) hoping to find a rough or blistered place on them. But they were both smooth with no irregular places. (replacing the elements would have been the easiest and cheapest repair. Pulled the back off the range (unplugged, of course) - checked wiring. There were no loose connections or burned wiring. I disconnected the elements and checked them with a ohmmeter (VOM) and both had continuity. Discovered that both elements used the same... Read more

Personally I have experience working with electricity and knowing if I bought the part required this would be an easy fix. I got my model number and contacted Appliance Parts Pros and placed my order for the new elements, terminal blocks, and for appearance purposes 4 new Drip Pans. Excellent service and quick shipping. I ordered my parts on Sunday and received them on Tuesday. This was a simple repair that only required a screwdriver to remove the old terminal block from the range hood, wire... Read more