Refrigerator Cap Or Cover

The Hinge-Sleeve Hole Plug is an OEM part for Whirlpool refrigerators. It is designed to cover the hinge sleeve holes on the refrigerator door, providing a finished look and protecting the internal components from dust and debris.

Common causes of a bad hinge-sleeve hole plug include physical damage during routine maintenance or accidental impacts. A missing or damaged plug can lead to exposure of internal hinge components, potentially causing further damage over time.

Symptoms of a bad hinge-sleeve hole plug include:

• Visible gaps or holes in the refrigerator door hinge area
• Accumulation of dust or debris in the hinge mechanism
• Loose or unstable refrigerator door hinges

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This replacement filter cap secures the filter in its housing and helps maintain a proper, watertight seal. It restores a snug fit when the original cap is cracked, stripped, or missing to help prevent drips and performance issues. What it does:

• Locks the filter into place and helps provide a reliable seal
• Helps prevent water seepage at the filter housing
• Restores proper fit when the cap is worn, rounded, or broken
• Common symptoms: dripping around the filter area, filter won't stay seated, difficulty tightening or removing the cap

• 1 filter cap

• Disconnect power; shut off the water supply before servicing
• Place a towel to catch residual water and access the filter housing per your model's instructions
• Remove the old cap; align and hand-tighten the new cap until snug—do not overtighten
• Restore water and power, then test and check for leaks; ensure any separate O-ring used by your model is present and in good condition

This water filter cap secures the refrigerator's water filter inside its housing and provides a handhold for easy removal. Replace a cracked or missing cap to maintain a proper seal and help prevent leaks during filter changes.

• Locks the filter into place for a tight, reliable seal
• Provides grip to twist the filter in and out of the housing
• Helps prevent drips at the filter connection
• Common symptoms: cap cracked or missing, hard-to-turn filter, filter won't stay seated, or water leaking from the filter area

• Turn off the water supply and dispense water to relieve pressure
• Place a towel under the filter area to catch any residual water
• Remove the old cap by turning it counterclockwise; attach the cap to the filter end
• Insert the filter/cap assembly, align tabs, and turn until it stops—hand-tight only; restore water and check for leaks

This evaporator door is the movable flap that opens and closes to control airflow from the evaporator section. A working door helps maintain stable temperatures and balanced cooling between compartments for consistent refrigerator performance.

• Regulates airflow from the evaporator through the air duct
• Helps keep fresh food and freezer temperatures within set ranges
• A stuck, broken, or warped door may cause warm spots, overcooling, or frost at air vents
• Can contribute to fluctuating temperatures or clicking from the damper actuator when the door won't move

• Unplug the refrigerator before servicing; wear cut-resistant gloves
• Access the air duct/damper area per your model to reach the door
• Reuse any existing clips, seals, and hardware from the original assembly
• Verify the door moves freely before reassembly; restore power and allow up to 24 hours for temperatures to stabilize

This is not a filter. Use this bypasss if don't want to use the PureSource 2 Water Filter WF2CB or the Pure Advantage Water Filter EWF2CBPA.

This is the small trim cap that snaps over the end of a refrigerator door handle. It finishes the handle, covers the mounting hardware, and helps keep the handle secure and looking clean.

• Covers exposed door-handle screws and mounting points
• Restores a finished appearance if the original cap is missing or damaged
• May help reduce handle looseness if the old cap no longer held properly
• Common symptoms: missing end cover, visible handle screws, loose or rattling handle

• Unplug the appliance before starting and open the door for access
• Remove the old cap by gently prying at the seam; avoid scratching the door finish
• Align the new cap with the handle end and press until it snaps fully into place
• If required, tighten handle mounting screws before installing the cap

The Filter Cap is an OEM part for Whirlpool refrigerators. It seals the water filter housing chamber located inside the refrigerator. The cap plays an important role in properly securing the water filter cartridge and ensuring a tight seal that prevents leaks.

Causes of a bad filter cap can include cracks, deformities, or warping of the cap due to pressure fluctuations over time within the filter housing chamber. 

Symptoms of a bad filter cap include:

• Water leaks from around the filter area  
• Inability to securely lock the filter cartridge in place
• Premature wasting of water when the filter is not fully engaged

This Whirlpool replacement part is compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This replacement cover protects internal components and completes the assembly's enclosure. Replace a cracked, loose, or missing cover to restore proper protection and fit, helping the appliance operate safely and as designed.

• Shields internal parts from dust, spills, and accidental contact
• Helps maintain intended airflow or enclosure integrity
• Restores secure mounting; reduces rattles and vibration
• Replace if the cover is cracked, warped, missing, or won't stay secured
• Common signs: broken/stripped tabs, visible damage, or persistent rattling

• Disconnect power before service; shut off water or gas if applicable
• Wear cut-resistant gloves—edges can be sharp
• Retain and reuse original screws/clips; transfer any reusable seals or labels from the old cover
• Align tabs/fasteners and tighten evenly without overtightening; verify no interference before restoring power

This replacement duct cap assembly covers and seals a designated duct opening inside the appliance. It helps direct flow through the intended path and keeps out debris so the system can operate as designed.

• Covers and seals a duct opening to maintain correct internal flow paths
• Helps prevent air/moisture leaks and blocks dust or debris entry
• Replaces a cracked, warped, loose, or missing cap assembly
• Symptoms can include visible damage, a cap that won't stay seated, leak noises, or rattling from the duct area

• Disconnect power; turn off water supply if applicable before servicing
• Access the duct location, remove the damaged cap, and retain any screws/clips
• Clean mating surfaces; transfer any reusable seals or hardware to the new assembly
• Seat and secure the new cap without overtightening; restore power and check for a snug, leak-free fit

This replacement cover restores the appliance's finished appearance and protects internal components from dust and debris. It's a direct-fit exterior trim piece designed to replace a cracked, broken, or missing cover. What it does:

• Protects internal components and wiring from debris and accidental contact
• Restores the appliance's cosmetic appearance and helps maintain sealing
• Helps reduce dust buildup in the covered area
• Replaces damaged or missing trim that can expose sharp edges or hardware

• Disconnect power (unplug or switch off circuit breaker) before beginning work
• Basic hand tools may be required; follow for panel removal/replacement
• Handle carefully to avoid scratching the finish and watch for sharp edges
• Replace with manufacturer-recommended fasteners

Refrigerator Filter Bypass Cap is an essential component for maintaining the optimal performance of your Samsung refrigerator. This genuine OEM part is designed to seamlessly integrate with a variety of Samsung refrigerator models, ensuring a perfect fit and reliable functionality. The filter bypass cap allows you to bypass the water filter when necessary, providing flexibility during filter replacements or maintenance without disrupting your refrigeratorGÇÖs operations. Its durable construction ensures long-lasting performance, helping to maintain consistent water flow and ice production even when the filter is not in use. Installing the Refrigerator Filter Bypass Cap is straightforward, making it easy for you to manage your appliance without the need for professional assistance. By choosing this genuine OEM part, you ensure that your refrigerator continues to operate efficiently, preserving the quality and freshness of your stored foods and beverages. Enhance the functionality of your Samsung refrigerator with the Refrigerator Filter Bypass Cap , a reliable solution that supports a smooth and uninterrupted cooling experience.

The Water Filter Cap is an OEM part for Bosch refrigerators. This secures the water filter within the refrigerator, ensuring a snug and leak-free fit. 

The need for a replacement can arise if the original cap is lost during a filter change, damaged, or wears out over time. 

Symptoms of a missing or damaged Water Filter Cap include:

• Difficulty in installing or securing the water filter properly, which could lead to water leaks inside the refrigerator.
• Contaminants or particles in the dispensed water, indicating that the filter is not fully sealed and thus not effectively filtering the water.
• The water filter becoming loose or falling out, compromising the refrigerator's ability to provide clean, filtered water.

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This plug covers the small factory test opening on an appliance cabinet or liner. Replacing a missing or damaged plug helps close the opening to maintain a better seal and restore a clean, finished appearance.

• Seals the factory test opening in the cabinet/panel
• Helps limit air and moisture infiltration through the hole
• Reduces condensation or frost forming around the opening
• Restores a finished look when the original cap is missing or damaged

• Disconnect power before servicing the appliance
• Clean and dry the opening area for proper fit
• Align and press the plug in by hand until it sits flush—do not force or enlarge the hole
• Avoid sharp tools or sealants that could damage the liner or insulation

This emitter cover is the molded housing that shields and positions the infrared emitter for the refrigerator's ice level optics. Replacing a cracked or missing cover helps protect the board and keep the beam path clear for reliable ice making. What it does:

• Shields the emitter board and lens from moisture, frost, and debris
• Aligns the infrared beam path across the ice bin to the receiver
• Helps secure and position the ice level optics assembly
• Common symptoms: broken/missing cover, intermittent or no ice production due to optics misalignment or obstruction

• 1 emitter cover

• Disconnect power to the refrigerator before servicing
• Remove the ice bin to access the optics components
• Release the old cover's retaining tabs or fastener and lift it off; avoid touching board components
• Position and secure the new cover, then restore power and test ice maker operation

This cover encloses and protects a designated area on the appliance, shielding internal components from debris and moisture while restoring a clean, finished look. Replace a cracked, warped, or missing cover to maintain safe operation and proper fit.

• Encloses and protects internal wiring or mechanisms in the covered area
• Helps keep dust, spills, and moisture away from components
• Restores a secure fit and finished appearance
• Common signs it's needed: broken tabs, cracks, discoloration, or the cover won't stay in place

• Disconnect power to the appliance before servicing
• Remove any retaining screws or release tabs; keep track of hardware for reassembly
• Transfer clips, seals, or inserts from the old cover if applicable
• Align tabs and start screws by hand; do not overtighten to avoid cracking

Color: White