Refrigerator Control Board

This defrost timer assembly cycles the refrigerator between cooling and defrost modes to prevent excess frost buildup and help maintain consistent temperatures. Replace a failed timer to restore regular defrost scheduling and reduce icing. What it does:

• Advances the refrigerator between cooling and defrost cycles on a timed schedule.
• Stops missed defrosts that can cause frost buildup on the evaporator and reduced cooling efficiency.
• Addresses symptoms such as excessive frost/ice, inconsistent temperatures, or a freezer that runs constantly.
• Acts as the control that engages the defrost heater and returns the unit to cooling when the cycle finishes.

• Disconnect power to the appliance before servicing to avoid shock or injury.
• Access the timer via the control panel or rear service area; document wiring or take photos before disconnecting.
• Install the timer in the same orientation and reconnect wires to the original terminals; do not force connectors.

The Control Board Box is an OEM replacement part for Whirlpool refrigerators. Housed internally, it contains the digital control board that regulates all refrigerator functions. 

Symptoms of a faulty control board box include:  

• Lights or compartments not functioning properly
• Inability to adjust temperature settings  
• Fluctuating interior temperatures
• Refrigerator failing to power on or cool 

Causes can be moisture damage over time compromising electronics, accidental impact trauma to the plastic case, or standard component degradation during usage cycles. 

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, and Kenmore models.

This inverter box is the electronic module that conditions and routes power to the refrigerator compressor, helping restore variable-speed compressor operation and consistent cooling when the inverter has failed. What it does:

• Regulates and converts power for the compressor's inverter drive to support variable-speed operation.
• Replaces a failed inverter module that can cause the compressor not to start or to run intermittently.
• Commonly used when the refrigerator runs warm, cycles abnormally, or displays inverter-related errors.
• Houses the control electronics for compressor power management.

• Always disconnect power before servicing the appliance to avoid shock.
• Access may require removing the rear or control housing panels; note wire routing and connector positions before disconnecting.
• Handle as an electronic component: protect from moisture, impact, and static discharge.

This 5-button dispenser control board runs the refrigerator's ice/water dispenser user interface. Replace it to restore button response, indicator lights, and proper dispenser selections when the original board is unresponsive or erratic.

• Interprets dispenser keypad inputs and communicates selections to the appliance's control system
• Drives the dispenser panel's indicator lights and status feedback
• Coordinates ice and water dispensing functions based on user commands
• Common symptoms include no response to buttons, dispenser lights/indicators not working, inability to change selections, or intermittent/erratic UI behavior

• Disconnect power before servicing; use ESD protection when handling electronics
• Remove dispenser trim/panel to access the board; release locking tabs and unplug the wire harness
• Transfer any reusable overlay or mounting hardware from the original board if applicable
• Seat connectors fully, reassemble, and test dispenser functions before finalizing

This is a genuine main control board for refrigerators. The main control board is what handles the functions of the fridge, including defrost times and temperature control. The board can become damaged over time and the electrical components could wear out from regular use. If the control board is not working properly, the refrigerator may not be able to maintain a proper temperature.If the control board is faulty, it needs to be replaced as soon as possible. Always disconnect the refrigerator before beginning any repairs. Be sure to wear gloves to protect the hands and work carefully with the small electrical parts so that they aren't damaged during installation.This genuine OEM replacement part is manufactured to exact standards and will provide a perfect fit for compatible machines from Whirlpool, Maytag, Jenn-Air, Estate, Kenmore, and others. The assembly is sold individually and does not include any hardware or wiring accessories.

This is an LG primary control board display assembly for refrigerators. The main function of this component is to control the display screen on the front of the refrigerator and control its main roles.When the refrigerator's main display on the front of the appliance malfunctions and doesn't display properly, the main issue is most likely the PCB display assembly. This allows a user to control several other functions of the refrigerator, including temperature setting, defrost, and ice maker settings. These malfunctions can be remedied by installing a new PCB display assembly. Always unplug the appliance before making any repairs. Wear gloves if possible.This product is a genuine OEM part sourced directly from the manufacturer. The primary control board display assembly is only available as an individual component and does not include any other parts or the original appliance. This primary control board display assembly is designed for installation in LG refrigerators.

The Main Control Board is an OEM part for Frigidaire refrigerators. As the central "nerve center" regulating all appliance functions, it monitors temperatures, operating modes, and safety features through embedded computing power.

Symptoms of a faulty control board involve:  

• Failure to properly cool or function in temperature control modes
• Unresponsive display or non-working buttons and sensors  
• Error codes or diagnostic messages appearing

Common causes are moisture damage degrading circuit boards over time, electrical component burnout from power surges, or physical impact compromising fragile boards.

This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore refrigerator models. 

This refrigerator main control board is the central electronic module that coordinates cooling, fan operation, and defrost cycles. Replacing a failed board helps restore stable temperatures and reliable overall performance. What it does:

• Controls compressor operation and cooling cycles
• Drives evaporator and condenser fan motors
• Manages automatic defrost heater timing
• Interprets temperature sensor inputs to maintain setpoints
• Resolve: refrigerator/freezer not cooling, fans or compressor not running, frost buildup, or clicking/chattering from the control area

• Disconnect power before servicing; use proper ESD precautions and handle the board by its edges
• Photograph wiring and label connectors to ensure accurate transfer to the new board
• Transfer any jumpers or mounting hardware from the original board as required
• After installation, restore power and allow time for temperatures to stabilize

This main power control board is the refrigerator's central electronic controller. Replacing a failed board can restore power and correct operation of the compressor, fans, lights, and user interface for reliable, consistent cooling performance.

• Supplies and manages power to the compressor, fans, defrost heater, lights, and control circuits
• Interprets temperature-sensor inputs to coordinate cooling and defrost cycles
• Failure may result in no power or unresponsive controls/display
• Other possible symptoms: intermittent power, clicking from the board, lights out, compressor or fans not running, and poor/no cooling

• Disconnect refrigerator from power before servicing; do not work on live circuits
• Use ESD protection and handle the board by its edges
• Photograph and label all connectors; transfer any jumpers, brackets, or covers from the original board as needed
• Ensure all harnesses are fully seated and covers reinstalled before restoring power

The electronic control board is the central circuit board that governs temperature settings and coordinates cooling-system operations. Replacing a failed board can help restore accurate temperature regulation, normal cycling of components, and responsive controls.

• Interprets temperature sensor input and maintains the selected setpoint
• Controls compressor and evaporator fan run times to regulate cooling
• Coordinates the defrost system in frost-free models
• Common symptoms of a failing board: no cooling, erratic temperatures, unresponsive or flickering display/buttons, or intermittent operation

• Disconnect power before servicing to avoid electrical shock
• ESD-sensitive component; handle by the edges and avoid touching circuitry
• Photograph wiring and transfer connectors one at a time to the new board
• Access and fasteners vary by model; refer to the unit's tech sheet or service manual

This electronic control board replaces the appliance's main control module to restore reliable cycle control and user-interface functions. It manages timing, sensor inputs, and commands so the appliance operates as intended. What it does:

• Receives inputs from buttons/sensors and directs motors, valves, and heaters
• Controls cycle timing, displays, and program selection
• Common symptoms: no display or erratic displays, touchpad/buttons not working, or cycles that stop or won't advance

• Disconnect power (unplug or shut off breaker) before servicing
• Handle the board by its edges and avoid contact with circuit traces
• Verify connectors seat fully and match original harness orientation

This encoder board assembly interprets user input from the range/oven control console and sends the correct signals to the appliance control system, restoring reliable button/knob response and control selection behavior. What it does:

• Converts knob/button movements into electronic signals the main control can read
• Helps ensure accurate selection of temperature, modes and timers
• Common symptom: controls are unresponsive or selections don't register
• Common symptom: erratic or intermittent control behavior when using the console

• Disconnect power at the breaker before starting any work
• Handle the board carefully and avoid static discharge; ground yourself or use an anti-static strap
• Keep track of screws and mounting hardware; label harnesses or take photos before disconnecting
• Reconnect harnesses fully and test function before reassembling the console

A replacement PUR-BETA control module that restores control for the refrigerator's PUR water/dispense/filter functions so the dispenser, filter status and related signals operate properly. What it does:

• Manages electronic signals for the PUR filtration and dispenser circuitry
• Communicates filter status and reset information to the fridge control system
• Controls/coordinates water and dispenser-related functions tied to the PUR system
• Common symptoms of a failing module include unresponsive water/ice dispenser, persistent filter-status light, or intermittent dispenser operation

• Always disconnect power (and water supply when applicable) before servicing to avoid shock or water damage
• Handle the module carefully and avoid static discharge; use a grounded wrist strap if available
• Some panel removal and connector unplugging is required; keep track of screws and connectors

This electronic control board manages your refrigerator's core functions. It processes sensor inputs and directs cooling, defrost, and fan operations so temperatures stay consistent and the unit responds to the controls.

• Coordinates compressor, evaporator, and condenser fan operation for proper cooling
• Controls the automatic defrost cycle based on sensor feedback
• Can cause no-cool, intermittent cooling, or unresponsive controls when it fails
• May help with erratic temperatures, frequent cycling, or clicking from the control area

• Disconnect power before servicing; this is a sensitive electronic component
• Handle by the edges and use anti-static precautions
• Note/photograph wire connections and transfer one connector at a time
• Mount the board securely; restore power and verify normal operation per the service instructions

Color: White

This electronic control board is the appliance's main logic module, managing cycles, timing and the user interface to restore responsive controls and proper operation. Ideal when pushbuttons, displays or automatic functions fail. What it does:

• Controls cycle selection, timing and program sequences for the appliance's functions.
• Sends signals to motors, valves and heaters so components run at the correct times.
• Interfaces with the user controls and display; helps interpret button presses and touch inputs.
• Common symptoms this part can cause: unresponsive controls or display, stuck or non-advancing cycles, random errors or failure to start.

• One electronic control board

• Disconnect power before beginning work to avoid electric shock.
• Handle the board by the edges and avoid touching components; use an anti-static strap if available.
• Compare the replacement board to the original to ensure matching connectors and mounting points.
• Reassemble panels and verify operation.