Refrigerator Hose Or Tube

This drain hose carries water away from your appliance during draining to help prevent backups and leaks. Replace a cracked, clogged, or kinked hose to restore reliable water removal and protect surrounding floors and cabinets. What it does:

• Directs drain water from the outlet or pump to the designated discharge point
• Maintains proper flow; kinks or blockages can cause slow or no draining
• Helps prevent leaks from splits, pinholes, or loose connections
• Common signs: standing water, water under/around the unit, drain-related error codes, or odors

• Includes 1 drain hose

• Disconnect power and shut off water supply before servicing
• Place towels or a shallow pan to catch residual water when removing the old hose
• Note the original routing; seat connections fully, secure with clamps, and avoid sharp bends or kinks
• Run a brief drain/rinse and check all joints for leaks

This refrigerator water leakage repair kit improves defrost drain heat transfer and routing so meltwater can flow to the drain tube. It helps reduce water pooling or ice sheets in the fresh food section from a frozen or restricted drain. What it does:

• Directs heat toward the drain opening to help prevent ice buildup that blocks drainage
• Promotes proper meltwater flow from the evaporator area into the drain tube
• Often installed to address water/ice on the bottom of the refrigerator compartment or puddles on the floor after defrost
• Helps reduce recurring defrost drain freeze-ups and overflows

• One water leakage repair kit

• Disconnect power and turn off the water supply before servicing
• Empty the compartment and remove shelves/drawers, then take off the rear evaporator cover to access the drain
• Clear all ice and debris from the drain and drain tube before installing the kit
• Install components exactly as directed for your model and water drains freely before reassembly

This water outlet tube routes water within the appliance's water system, maintaining a secure, leak-resistant path to its outlet. Replace a cracked, kinked, or leaking tube to restore proper water flow and prevent leaks. What it does:

• Directs water from internal plumbing to the designated outlet/assembly
• Maintains a sealed connection to help prevent drips and leaks
• Typical failure symptoms: water leaking inside or onto the floor; weak or no water flow; visible cracks, kinks, or a loose fit at connections

• 1 water outlet tube

• Disconnect power and shut off the water supply before servicing
• Note tube routing and connection points; remove any clips/fasteners as needed and pull the old tube free
• Fully seat the new tube into each port; ensure any existing seals or clips are positioned correctly
• Run a short test cycle and check all joints for leaks

This refrigerator water tube carries fresh water between the valve, reservoir, dispenser, and/or ice maker. Replacing a cracked or kinked tube restores proper water flow and helps stop leaks inside or behind the refrigerator.

• Directs pressurized water between components in the refrigerator's water system
• Common failure signs: leaks, visible cracking, kinks, or pinhole sprays
• May cause no or slow dispenser flow, or an ice maker that doesn't fill
• Restores correct routing after tubing becomes brittle or damaged with age

• Unplug the refrigerator and shut off the household water supply before servicing
• Place a towel under connections and dispense water to relieve line pressure
• Depress quick-connect collars or loosen clamps to remove the old tube; route the new tube exactly like the original
• Fully seat tubing in fittings, perform a gentle tug test, restore water, check for leaks, and flush several cups to clear air

This straight 1/4-inch water line coupler joins two sections of 1/4-inch OD refrigerator tubing, restoring a secure connection in dispenser and icemaker supply lines. Use it to splice, repair, or extend existing tubing.

• Creates an inline union for 1/4-inch OD refrigerator water tubing
• Helps address leaks, cracks, or breaks by replacing a damaged connector or splicing a cut line
• Useful when rerouting lines or adding inline components such as filters
• Common symptoms: water dripping at a tubing joint, loose/disconnected line, reduced or no water to dispenser/ice maker

• Unplug the refrigerator and turn off the water supply; dispense water to relieve pressure
• Cut tubing ends square and clean; ensure both tubes are 1/4-inch OD
• Make secure connections per the coupler design (push-to-connect or compression); ensure tubing is fully seated/assembled and gently pull to verify
• Restore water and check thoroughly for leaks

This water supply tube connects at the inlet water valve, routing water through your appliance's water system. Replacing a brittle, cracked, or kinked line helps restore reliable, leak-free operation and proper water flow. What it does:

• Carries water from the inlet valve to the designated component (such as dispenser, icemaker, or filter housing, depending on model)
• Helps maintain proper water pressure and uninterrupted flow
• Common symptoms include leaks at the back/bottom, slow or no water at the dispenser, or an icemaker not filling
• Addresses visible cracks, brittleness, or kinks in the existing tubing

• 1 water supply tube

• Disconnect power and shut off the household water supply; relieve line pressure by dispensing water
• Place a towel to catch residual water and note the original routing before removal
• For push-in/quick-connect fittings, insert fully and tug back to verify engagement; if using compression fittings, tighten snugly without overtightening
• Turn water on and check all connections for leaks before restoring power

This water tube routes the household water supply from the inlet valve to the refrigerator's water filter. Replacing a cracked or kinked line restores proper dispenser and ice maker flow and helps prevent leaks around the filter assembly.

• Carries water from the inlet valve to the filter housing
• Helps maintain proper, unrestricted flow to the dispenser and ice maker
• Typical failure symptoms: leaks, visible cracks or kinks, reduced dispenser flow, no water at the dispenser, slow or no ice production

• Disconnect power and shut off the water supply before servicing
• Dispense water to relieve pressure and place a towel to catch residual water
• Note the routing; release the tube from retainers and fittings carefully
• Fully seat the tube in push-to-connect fittings, avoid sharp bends, restore water, and check for leaks

This plastic tube carries water within your refrigerator between internal components. Replacing a brittle, kinked, or leaking line restores dependable water flow and helps prevent drips that can damage interiors, cabinetry, or floors. What it does

• Routes water between internal components (such as valves, filters, reservoirs, and dispensers)
• Helps maintain proper water flow and pressure when intact and unkinked
• Typical failure symptoms: water leaks, slow or no water flow, visible cracks, flattening, or kinks
• Age- or heat-related hardening can cause stress cracks near bends or fittings

• One plastic tube

• Unplug the refrigerator and shut off the water supply before servicing
• Note original routing and clip locations; avoid sharp bends, abrasion points, and hot surfaces
• Insert tube ends fully into their fittings (quick-connect or compression, per design) and gently tug to confirm they're seated
• Restore water, purge air as needed, and check all joints for leaks before pushing the unit back

This refrigerator water inlet tube routes water from the supply/valve into the appliance's water system. Replacing a cracked or kinked tube restores proper flow to the dispenser and ice maker while helping prevent leaks.

• Directs water from the inlet valve to internal components for dispensing and ice production
• Maintains a sealed, food-grade water path
• Replace if you notice leaks under/behind the unit, visible cracks/kinks, reduced or intermittent dispenser flow, or ice maker not filling
• Normal wear, brittleness, or damage during moves can lead to failures

• Disconnect power and shut off the water supply before servicing
• Place a towel or tray to catch residual water when disconnecting lines
• Note the original routing; release any retaining clips and disconnect the tube from fittings
• Route the new tube exactly like the original and fully seat tube ends in connectors; restore water and check for leaks

This drain hose extension kit increases the reach of your appliance's drain line so it can connect to a farther standpipe or sink, supporting proper drainage and reducing stress on fittings that can lead to leaks. What it does:

• Extends the existing drain hose to accommodate installations where the drain connection is farther away
• Helps maintain a secure, leak-resistant connection when routed correctly
• Useful when relocating the appliance, changing cabinetry, or updating plumbing
• Common signs you may need it: hose won't reach, kinks when stretched, or occasional water near the drain line

• One drain hose extension kit

• Disconnect power and shut off the water supply; have a towel or pan ready for residual water
• Join the extension to the existing drain hose with the proper coupling/clamps; tighten securely and avoid kinks or sharp bends
• Route and support the drain line per your model's installation guide and observe any maximum total hose length
• Run a short test cycle and check all joints for leaks

This is a replacement ice maker fill tube. This is a genuine OEM part made by LG and has been sourced directly from the manufacturer. This part is intended to replace broken or detached ice maker fill tubes in a variety of refrigerators. This piece of plastic tubing supplies the in-built refrigerator ice maker with water so it can make ice. If the ice maker is not working properly and is not making ice, there may be an issue with the tubing. Always make sure that the refrigerator is entirely disconnected from power and water before starting the any repair work. Please ensure that the appropriate safety precautions are followed when attempting to fix any appliances. For more accurate information on how and where to install this ice maker fill tube, the appropriate owner's manual and included diagrams should be referenced.As an authentic replacement part, this ice maker fill tube is suitable for use on several different models of refrigerators manufactured by LG and Kenmore. This is a genuine part made of high-quality, durable plastic and is sold individually.

This spigot routes water from the internal supply to the dispenser outlet, delivering a controlled stream. Replacing a cracked or worn spigot helps restore proper dispensing and reduces drips or leaks at the dispenser area.

• Directs water from the internal tubing/reservoir to the dispenser outlet
• Maintains a defined flow path to help prevent splashing and after-drip
• Common symptoms of failure: dripping at the dispenser, slow/erratic flow, leaks inside the door, or visible cracks at the outlet
• Replace if damaged, leaking, or obstructed by mineral buildup

• Unplug the appliance and shut off the household water supply
• Dispense water to relieve line pressure before replacement
• Access the dispenser; note tubing orientation and fully seat/secure connections
• Restore water and power; flush the system and check all joints for leaks

This water fill extension tube assembly directs water into the ice maker's fill cup, providing a clear path for each cycle and helping reduce leaks or ice buildup caused by a cracked, misrouted, or blocked tube.

• Routes water from the inlet toward the ice maker fill cup
• Maintains a clear, controlled water path to help minimize drips and spray in the freezer
• Replaces cracked, kinked, or frozen fill tubes that can disrupt ice production
• Typical symptoms: ice maker not filling, water dripping/pooling in the freezer, or ice/frost around the fill area

• Disconnect power and turn off the household water supply before service
• Access the fill tube at the freezer/ice maker area; thaw any ice with warm air—avoid sharp tools or excessive heat
• Match the original routing and insertion depth; seat the tube fully in the fill cup/channel
• Restore water and power, then run a fill cycle and check for leaks

This water tube connector joins sections of your refrigerator's water line for the dispenser and ice maker. It restores a secure, leak-resistant connection when the original coupling is damaged or leaking.

• Connects two segments of refrigerator water tubing
• Helps maintain proper water flow to dispenser and ice maker
• Resolves leaks caused by a cracked, worn, or loose connector
• Useful when replacing or rerouting water lines during service

• Disconnect power and shut off the water supply before servicing
• Dispense water to relieve line pressure
• Cut tubing square and insert fully until seated; tug gently to confirm a secure fit
• Restore water and check all connections for leaks; replace any damaged tubing as needed

This water connector links sections of the refrigerator's water supply tubing, maintaining a sealed path to the dispenser and ice maker. Replace a cracked or leaking connector to stop drips and restore reliable water flow and ice production.

• Connects sections of internal water tubing between components (inlet valve, filter, door, ice maker)
• Helps maintain a sealed route for proper dispenser and ice maker operation
• Common symptoms: water leaking behind/under the refrigerator, weak/no dispenser flow, ice maker not filling, visible damage at the fitting
• Direct-fit component built to OEM specifications for the intended application

• Unplug the refrigerator and shut off the household water supply before servicing
• Dispense water to relieve line pressure; place a towel to catch residual water
• Cut tubing ends square and fully insert into the connector until seated; tug gently to confirm engagement
• Restore water, check carefully for leaks, and recheck after the first dispense cycle

This water inlet tube routes incoming water inside the refrigerator, restoring a secure, leak-resistant path for the ice/water system. Replacing a damaged tube helps prevent leaks and ensures proper filling where the system needs it. What it does:

• Carries water from the supply/valve to the internal fill point
• Replaces tubing that is cracked, kinked, brittle, or leaking
• Helps resolve water drips at the rear or around the fill area
• Clears the path so blockages don't reduce or stop filling/ice production

• 1 water inlet tube

• Disconnect power and shut off the water supply before servicing
• Pull the refrigerator forward carefully for rear access and protect the floor
• Match the original routing; transfer any model-specific clips or seals if present
• Restore water, purge air, and check all connections thoroughly for leaks