Refrigerator Ice Maker & Related

1. Viewed YouTube video twice to learn how to change out the Samsung ice maker 2. Followed the instructions So easy to do yourself. I would not spend anytime hiring someone to replace this part for you. Read more

Take off freezer door and tried to take off top shelf. Never got shelf off. Made it more difficult but got it replaced. Read more

• Ice maker dispenses too much ice

Item delivered to my door in 1 1/2 days, priced $40 below other sites I had checked. Installed in 15 minutes. Just know that when installing an ice maker they don't start to make ice immediately. It can take several hours Read more

I found that the Ice Maker in my GE side by side made ice but would not kick out the ice when it had formed, the heating element or the switch that controls it didn't work. I ordered a new ice maker switched it out took less than 3 minutes. The cord was very stiff and just long enough but I got it to connect and in 35-40 minutes I had fresh ICE!! Read more

Purchased the kit, followed instructions, within 30 minutes had the new ice maker installed. Works wonderfully. We were quoted over $350 to fix it from a repair agent, but it only cost $150 including shipping from you guys. Very happy. Read more

Replaced entire ice maker. A couple of important points. (1) The ice maker module does not include all parts. The door flap for example is not included. So save all plastic parts from the old unit including screws. The biggest installation problem was the power cable. There was little room on the side of the ice maker for the cable and connectors to fit. Make sure the connector that mates with the refrigerator cable is seated onto the plastic housing and does not stick out or dangle out.... Read more

• Ice maker won't dispense ice

I first thought it was the auger in the ice container so I changed it and it was not the problem. I then talked to ApplianceParts customer service that it might be the yoke on the motor that turned the auger or even the motor itself even though it worked. I ordered the parts, the yoke was supposed to be able to be changed by itself but mind would not come off the motor shaft so I had to cut it off just to remove it from the unit so I had to change the motor anyway because of this. So I advise... Read more

Well, I took it out (it slides out) to get a good look at it,so i could ref pictures on your site..naturally I had serial/model of refrig,and thats mandatory to get the right part. It came in 2 days,,and being just the bucket, it took only a few minutes to transfer the auger assembly/cube/crusher.... into the new one, 6 screws total..Your site has excellent vids on DIY.......I HIGHLY reccomend. Whole process was'nt over 15 minutes, piece of cake....And NOW i can go back to my nightly 'scotch... Read more

It was a snap. All I had to do was unsnap one end of where the ice tray attached to the ice maker and fit the tray into the two sides and then resnap the end back onto the icemaker. Very easy. Read more

Although the solenoid I purchased did not fix the problem, nor the "mother electronic board", or the motor, my experience with Appliance Parts Pros has been excellent. Extremely easy to look-up parts for my model refrigerator. Best part is their video instruction that gives you step-by-step hands-on how to remove and install. I would highly recommend these folks. If a lady such as myself can do repairs based on their instruction, anyone can. Thank you for providing such an informative... Read more

Replaced fill tube and ice maker Read more

• Ice maker dispenses too much ice
• Leaking
• Ice maker not making ice

Watched online video and worked along - it was easy and quick - I was amazed! Read more

Removed old seal and installed new seal. I laid down the new seal in the sun for about 20 minutes and it went in the grove extremely easy. Read more

I broke the ice bucket when the problem first started as I kept trying to get the ice out of the dispenser. I replaced the Icemaker Asembly in less than 5 minutes, 1 screw and that was that. Everything works great and my dispenser is back in action. I did have a repair man come out to correctly diagnose the issue as the parts were expensive and I wanted to make sure it was not a leak somewhere, but indeed the mechanism. He charged me 40 to confirm the issue and I ordered the parts. Could... Read more

Ordered new tray. Read more