Roper Parts

Removed LP Orifice and LP Gas limiter. Orifice was easy, however the gas limiter was the tricky one because I had no instructions to what went where. I could not find anything online as to how to convert from LP to Natural Gas, but you could find several things as to how to convert from Natural to LP. I ended up finding the Dryer schematic on line for the Whirlpool Duet natural gas dryer and was able to figure out what sequence the Spring, regulator and limiter went in. The order I just... Read more

Once the parts arrived, I followed the help video that was emailed to me with my order confirmation step by step. Super useful! The video quality and editing were well done and the instructions were very specific. I felt like a pro! Read more

, shut gas valve to range, unplug from wall outlet, ordered thermostat. less then 30 minutes to install new thermostat, range back to normal function Read more

I ordered a new basket. I took out the old one and put in the new one. Pretty simple Read more

Bot both sets of roller bearings, lower ones on the appliance and the set on the trash can that rolls out. I just followed the instructions that were in the roller bearing package and only needed the tools that are recommended. Was a little tricky with the nuts, really need a person with "small" fingers to reassemble the nuts back on the lower set of bearing that are on the appliance. All in All, went well and works. Found that the new bearings are v. tight on the machine, being new, so, use... Read more

I ordered the complete assembly ice bucket and all Read more

Quick replacement by sliding out the old filters and sliding in the new filters. Read more

I knew for sure that the hinge with the large spring was damaged, but elected to replace both hinges and receivers. Replacing the parts was fairly easy and would have taken me less then an hour. This model has thin metal covers over the hinge assemblies. I found that squeezing in the sides of the covers help to hold them in place on the hinge while reassembling the door. My only difficulty was putting the door back on the oven. It took a little maneuvering but I managed to get it. Now the door... Read more

I reviewed the schematic and saw the Volute Seal, and Impeller Seal were the two that were closest my source of water. After watching the video about changing the Impeller/seal I removed the motor, impeller, and volute; I found that the impeller seal was the faulty one in my case. Since I'd ordered the volute and impeller seal kits (as I wasn't sure which it was) I installed both while I had it apart. Runs great, no water - simple to do. The seal changes took about 20 minutes. The only... Read more

Had to replace the auger. The auger on my ice maker was made of plastic and had broken pieces off it. The new one is made of metal and seems to work much better. Was a fairly simple repair. However pay close attention when disassembling, I recommend using your cell phone and snap a pic of the different stages as I became a little confused when putting it back together. Ordered the part and it was here the next day. I'm very happy to have my ice coming down the chute again. By the way, I'm a 70... Read more

• Element will not heat

Purchased a new Element surface and installed same... All Okay now... Read more

I removed the kick panel/door and confirmed there was no flame. Inspection with a flashlight revealed the igniter was damage - partly broken away. Using a 1/4" socket set I removed the burner assembly. Inspection showed the burner was rusted and the flame deflector had fallen off. I ordered both the "Dryer Igniter and Bracket" and a burner. They arrived in about three days. I had to attach the igniter to the bracket (one screw) and then the bracket to the burner (one screw). The only... Read more

Followed the instructions. Easy... Read more

Looked up parts on internet using diagrams, ordered parts, they arrived in 2 days and installed them. Read more

Watched a few of your well put together videos and could not afford a new Refrigerator right now because it was a built in so decided with the frost on the bottom of the freezer grill and the Refrigerator warming up decided to replace the Heater Element and Thermostat Defrost which took some time but so far so good lets hope that is all that is needed saved over 10,000.00 dollars for a new 48" built in for now! Thank you for your rushed order and videos I think you are a life saver got the part... Read more