Roper Parts

• Marks left on clothes

Our 19 year old Whirlpool dryer quit heating. After checking the thermal fuse, I found the ignitor electrically open. I bought an ignitor at a local store as there was a national holiday the next day and I did not want the dryer inoperative waiting several days for shipping. I can say AppliancePartsPros is MUCH cheaper for the identical Whirlpool genuine part. While changing the ignitor, I noticed there was an excessive amount of lint in the dryer, which was caused by worn drum seals. I ordered... Read more

• Little to no heat when broiling
• Little to no heat when baking
• Won't start
• Gas igniter glows, but will not light

There are two igniters in oven, one for top broiler and one for bake oven at bottom. Your website help me troubleshoot the problem and locate the part. ordered part was delivered the next day. Following the instructions that others on your website had provided, the repair was quick and SUCCESSFUL. No need to pull out oven as power cord can be accessed from removing bottom storage drawer. Step 1: Remove the storage drawer from below the oven and disconnect the power cord from inside. No need... Read more

When I removed the cabinet, all of the springs appeared in tact, I had already replaced the counter balance spring so I knew that was not the issue. None of the suspension springs or brackets were broken but they did look worn/rusty so I replaced all of the brackets (2 in front and 1 large in back), all of the suspension spring retainers, and all of the suspension springs and it fixed the issue! I plan to also replace the Self leveling leg spring which is an easy fix since it's on the back of... Read more

• Little to no heat when baking
• Oven not heating evenly
• Element will not heat

The first thing I did was call appliance pros. The tec told me it was a good chance it was the thermostat. He told how to test it with my ohm meter and what range it should be in. I pulled it out and tested it, which was out of the limits he told me it should be in. So I ordered the part. When it arrived in two days, I installed it. The oven now works perfect. Thank you so much. I was just about to go spend $800 on a new oven, and instead fixed it for $75. Awesome website. It was... Read more

Installed replacement drawer Read more

• Shuts off too soon
• No heat or not enough heat
• Takes too long to dry

I used Fixya as an initial source describing my problem. I got two responses which were very helpful. One that the "coils" were probably the problem. Two, that the problem could be the thermostat or a thermistor in the dryer. I verified that AC was coming from the timing control, that both the two terminal and three terminal coils,the igniter and shut off thermostat all had continuity. I then applied AC directly to the coils: the two terminal coil ""clanked" and I interpreted that as the coil... Read more

• Won't start
• Timer will not advance
• Will not drain

First I checked the circuit breakers and power to the outlet, then next wanted to check the lid switch, but it wasn't where I had found it on older models. I could hear it clicking on and off as I raised and lowered the lid, but it wasn't visible. I drained the tub through a siphon hose to lighten the machine, so I could slide it away from the wall to better see. Couldn't see the switch anywhere and decided it must be hiding in the raised console, but was unsure of how to attack it without... Read more

• Gas igniter glows, but will not light
• Won't start
• Little to no heat when baking

I watched a video by AppliancePartPros, and it showed the exact problem that I was having as well as what part that I would need for the repair. So I ordered the part which was and oven igniter, that also turned out to be the exact replacement for my old igniter.The part came in the mail in a about 3 days and I was able to install it myself in about 20 minutes give or take, with simple hand tools, then I did a quick test and everything worked fine. THANKS APPLIANCE PARTS PROS FOR ALL OF YOUR... Read more

After extremely poor support from WhirlpooI and researching numerous U-Tube videos, I fully troubleshot potential failed components and connections. All appeared to function properly, so I reassembled the unit and experienced the same problem as before. I then narrowed down the problem to either the Touchpad ($57+$8 shipping) or the control board ($295+shipping). If those did not work, then a new Microwave of better quality, reliability and support than original microwave, Unfortunately,... Read more

• Lid or door won't close
• Won't start

Not wanting to spend hundreds of dollars on an appliance technician's service call, I searched online to troubleshoot the problems with my particular Maytag Washer Model Number MVWX500BW0. I stumbled across AppliancePartsPros.com and investigated there the most likely causes for my Maytag Washer's not agitating properly and not spinning at all. In order to acquire some additional information, I telephoned AppliancePartsPros.com and spoke with an extremely professional, knowledgeable and helpful... Read more

• Will not drain

I've opened sump housing to check for clogging but it was clean. When I removed check valve to inspect it I've found out that the round part of the valve was missing so I figured it might've blocked the water exit at drain hose or something like that. So I pulled the dishwasher out to get a full access to drain hose connector and the pump. Upon disconnecting the drain and checking its connector I indeed found the round piece totally blocking the hose and acting as a seal. I removed the piece... Read more

• No hot or cold water
• Will not stop filling with water
• Will not fill with water
• Fills and drains at the same time

I watched the how-to video on your website to learn how to get at the valve to replace it. Before watching the video, I did not know how to take the washer cabinet apart to replace the valve. I searched on your website for my washer model, but the exact model number was not listed. I chose a very similar model number and looked up the info for that machine's replacement valve . It looked like it would work in my washing machine so I decided to take a chance and order the valve. I placed my... Read more

• Frost buildup
• Freezer not defrosting
• Freezer section too warm
• Fridge too warm

Condenser was encased in solid block of ice due to automatic defrost not working. Replaced thermostat and ADC control board. Working fine now. Most tedious part was using a heat gun to melt all the ice off the condenser coils. You will need a couple small wire nuts to splice the new thermostat into the existing harness (they are not included). Service tech wanted over $400 to repair, fixed it myself for half that. Thanks ! Read more

• Little to no heat when baking
• Oven not heating evenly
• Oven is too hot
• Won't start

My wife was using the oven and she shouted "emergency, oven fire" as i was half asleep in the reclining chair (I will be 86 in Oct.) As I dashed, well not quite, into the kitchen mentioning the fire extinguisher, she exclaimed "no, electrical fire, throw the circuit breaker"....which I very promptly did and the fire was no more; just a lot of bad odor. Removing the severed 32 year old bake oven element was somewhat delayed due to corrosion of the element mounting screws and electrical... Read more

• Door sweating
• Door won't open or close
• Clicking sound
• Fridge too warm

Replaced both sets of door cams on my Kenmore Elite Refrigerator. The most important thing to know is that you DO NOT have to remove the doors from the refrigerator to replace BOTH sets of cams. You just have to remove the lower grill which is a snap fit (I also turned off the water and unplugged the unit). My fridge has an ice and water dispenser where the water and electrical lines go through the cams on the left side. Be sure to order the correct parts as the cam holes on the freezer side... Read more

Took broken bin out and replaced with new one. No tools were required ( for the next section since it won't allow me to only select other). Read more