Roper Parts

• Frost buildup
• Freezer not defrosting
• Freezer section too warm
• Fridge too warm

Condenser was encased in solid block of ice due to automatic defrost not working. Replaced thermostat and ADC control board. Working fine now. Most tedious part was using a heat gun to melt all the ice off the condenser coils. You will need a couple small wire nuts to splice the new thermostat into the existing harness (they are not included). Service tech wanted over $400 to repair, fixed it myself for half that. Thanks ! Read more

• Fridge too cold
• Fridge runs too long
• Won't start
• Freezer section too warm

The 20 year old unit still serves us well, looks good and has been kept in good repair. The condenser fan had stopped so I removed, cleaned and oiled that motor. The decision was made to make an upgrade to the evaporator motor and control units so that the appliance could reasonably be expected to have extended service life. The Ice maker module had been replaced 7 years ago. I ordered the parts and have made the upgrade for temperature controller and the defrost control. If you are in a... Read more

Installed new agitator Read more

• Shakes and moves

I had previously replaced the pump about 1 year ago. That was not the problem. Still leaked the same way - intermittently, but always in the center of the washer onto the floor. None of the hoses were leaking - no evidence of corrosion or water mineral residue at any of the hose fittings. So, it must have been something else. I studied the parts diagram for the washer tub assembly and concluded the source of the leak almost had to be the outer tub's Centerpost Gasket. It was really the... Read more

• Leaking

I followed your step by step instructional online video. That is one great tool you are providing for your customers! Read more

• No heat or not enough heat
• Too hot

Since the dryer was 24 years old I opted to replace all the possible problem components, instead of just the bad one. The parts aren't that expensive and do to their age I figured it was worth it to avoid having to go back into the dryer in a few months. The repair was surprisingly easy and went pretty much as the video instruction AppliancePartPros provided with one exception. Because, my model was much older than that used in the video, I had a more difficult time replacing the Heating... Read more

I watched your video and had it fixed in less than 1 minute! Read more

Slid in new screen. Read more

• Leaking

I had previously replaced the pump about 1 year ago. That was not the problem. Still leaked the same way - intermittently, but always in the center of the washer onto the floor. None of the hoses were leaking - no evidence of corrosion or water mineral residue at any of the hose fittings. So, it must have been something else. I studied the parts diagram for the washer tub assembly and concluded the source of the leak almost had to be the outer tub's Centerpost Gasket. It was really the... Read more

• Takes too long to dry
• No heat or not enough heat

Our 19 year old Whirlpool dryer quit heating. After checking the thermal fuse, I found the ignitor electrically open. I bought an ignitor at a local store as there was a national holiday the next day and I did not want the dryer inoperative waiting several days for shipping. I can say AppliancePartsPros is MUCH cheaper for the identical Whirlpool genuine part. While changing the ignitor, I noticed there was an excessive amount of lint in the dryer, which was caused by worn drum seals. I ordered... Read more

• Will not tumble
• Takes too long to dry
• Noisy

I FOUND the website on t internet, found my part ordered it and watched the how to video ,repaired the dryer myself. Awesome Website. Read more

Remove upper and lower baskets for access. Remove 4 Torx screws holding drain/filter assembly, accessing last screw by rotating the water duct clockwise. Be sure to first un-clip the water duct at top and rear of dishwasher so that it can be moved. (Take the opportunity to remove accumulated deposits behind the water duct). Remove the drain/filter assembly and then remove the single screw holding the food chopper housing. Then remove the chopper assembly which is likely to be in pieces if it... Read more

• Not drying dishes properly

My Whirlpool dishwasher (wdf520padm3) started leaving food on dishes and not drying dishes as well as it used to, even when I ran the 'high temp' and 'heavy' cleaning options. This started happening after about 3 years of operation. To try to diagnose the issue, I started the diagnostics cycle (see below for instructions on how to do this). However, the 'Clean' LED is also not working on my dishwasher, so I was unable to read the error code after the service cycle finished. I decided to... Read more

• Will not stop filling with water
• No hot or cold water
• Will not fill with water

Replacing the water inlet valve fixed the problem. For many months we noticed cold water was just dribbling into the washer during the rinse cycle, and "warm" washes were hot not warm. It seemed like the cold water wasn't able to enter the machine. Then one day the cycle just stopped when it reached "rinse" and wouldn't go any further. I first tried solving it by cleaning the filter where the cold water hose enters the machine at the back. It was coated in sediment (the water comes from a... Read more

• Element will not heat

Replaced the burner Infinite switches for the burners having the issue. Here are the latest part numbers for this model Maytag. Left rear (LR) and right rear (RR) burners are both 6" and use the same switch. Part # WP3149404. Left front (LF) is an 11 1/2" burner Part# W10167742. The right front (RF) burner is a double burner 6" center and 9 1/2" outside burner Part #WPW10149355. Very simple repair. Unplug the stove, remove the rear panel, remove the switch knob, remove the 2 switch screws,... Read more

• Door won't open or close
• Door sweating
• Fridge too warm
• Noisy

Replaced both sets of door cams on my Kenmore Elite Refrigerator. The most important thing to know is that you DO NOT have to remove the doors from the refrigerator to replace BOTH sets of cams. You just have to remove the lower grill which is a snap fit (I also turned off the water and unplugged the unit). My fridge has an ice and water dispenser where the water and electrical lines go through the cams on the left side. Be sure to order the correct parts as the cam holes on the freezer side... Read more