Wall Oven Heating Element

I lifted the front hood and removed the back control panel cover. I then replaced two terminal blocks with the new kits. Perfect match except wires were a bit long. So I rolled them up neatly and tucked them away at the control center. Used electrical tape to band both sets of wire and protect them from the metal edges between the range and control area. I replaced the control cover and installed two new burners. Perfect installation. Read more

Order the part to ApliancePartsPro and within 3 days I had it delivered to my front door. Looked up in their help page and was guided how to do it. It was so ease . I will recomend all my friend to get their parts at ApliancePartsPro. I am very please with the service and quality. Read more

I ordered a replacement part, which arrived in a few days. My husband removed the burned out part and put in the new one. No problems! Read more

Replaced defrost heater, temperature and defrost limiter thermostat. After taking the cover off the air chiller I found the coils frozen solid and defrosted it with a hair dryer. Once defrosted I remover the heater coil to test it it was fine, then I could see the defrost limiter was broken and as I put the unit back together I broke the heater tube (it is glass) so I ordered all the parts that might be defective and replaced them for less than the charge of having some one come to check it out. Read more

• Element will not heat

Replaced the Infinite Switch and that solved the problem. Did not need to replace the Surface Element Read more

I ordered the 8 inch Haliant Element from Appliance Parts Pro with overnight shipping (I needed to have it working for Easter weekend!) and it arrived when promised and in perfect condition! To replace, you need a couple of boards longer than the stove is wide to hold the stove above the counter. You will also need a T15 Torx head on a handle or socket wrench. It also helps to have some pliers, and a second person to slip the boards under and out from the stove when you lift it. First, shut... Read more

• Little to no heat when baking

Turned off the power to the oven, removed the old element and installed a new element that I purchased from Appliance Pros.com. The part was delivered in a timely manner and was packed securely for shipping. Thanks!!!!!! Read more

• Little to no heat when baking

Repair video was very helpful. Followed the instructions and the element was replaced easily and correctly. Read more

Ordered the replacement Bake Element and installed it. Read more

• Little to no heat when broiling
• Element will not heat
• Little to no heat when baking

I ordered the bake unit from appliancepartspro.com; while ordering, I decided to go ahead and replace the oven broiler burner as well. Appliancepartspros.com's videos helped me replace the parts with ease. It took barely 30 minutes to install both. Plus, very fast shipping and correct parts. Now, I do not have to worry about baking during Thanksgiving! Cheers, Sean Read more

First, I took an ohm reading across the elements and determined the bad one, which was failed, open circuit. (Zero continuity) I then replaced the lower heating element of the upper oven. Although the design of the oven and element make it appear that it will just drop down and slide out the front, this is not quite the case. There is not enough clearance for it to drop all the way down. You have to pull the entire double-oven unit out of the wall, separate the upper and lower halves a few... Read more

I purchased a new elelmnt and fixed it myself!! Read more

Raised ceramic top, removed old element, installed the new one. Read more

1) ordered new boiler element after searching for oven/stove model # online 2) unplugged oven 3) removed 2 screws holding element in place 4) pulled out the element and a length of wires attached to the element (enough that the wires wouldn't pull back into the hole after detached) 5) used needle-nosed pliers to detach wire clamps, noting which wire attached to which side of the old element 6) removed old element and its pieces from the bottom of oven 7) attached wires to new element,... Read more

Installed new heater element. Read more

• Element will not heat
• Won't start

Turned off power supply. Removed two screws (near the oven door) holding the ceramic top. Slid the top forward, disengaged the two power supply cables, and removed one ground wire. Removed range top, and put on a flat surface. Unclamped two power supply wires, one ground wire and one thermocouple wire from the element. Unscrewed the bracket from the element, and remove the element from the range top. Remove the two clamps from the old element, and put them on the new element at the same... Read more