Wall Oven Parts

Removed the top and replaced 2 of the electrodes. Read more

First off thanks AppliancePartsPro.com... Another project in the books... I ordered a new switch harness and spark module because I just decided the why not do them both. They arrived very promptly, uses very simple tools most people have I would think. After unplugging it and shutting off the propane. I removed valve knobs. Then the burners with a nut driver and two sizes of sockets. The stove top and valve cover six Philips head screws. Gained complete access to the stove top. Removed... Read more

• Gas igniter glows, but will not light
• Won't start
• Element will not heat

After many years of excellent service the burner I use most often on the top of my JenAir range rusted through. After trying to remove the burner, which was firmly rusted into place, I decided to replace the cooktop pan, both burners and igniters. It was an easy repair to swap out the new parts for the old, and the only tool necessary was a #2 phillips screw driver. The only difficulty was that although the cooktop pan appears symmetrical, the screw hole pattern on each side is different. I did... Read more

1) ordered new boiler element after searching for oven/stove model # online 2) unplugged oven 3) removed 2 screws holding element in place 4) pulled out the element and a length of wires attached to the element (enough that the wires wouldn't pull back into the hole after detached) 5) used needle-nosed pliers to detach wire clamps, noting which wire attached to which side of the old element 6) removed old element and its pieces from the bottom of oven 7) attached wires to new element,... Read more

We sent an email to AppliancePartsPros.com asking for their help in fixing our range. We gave them the model number (NE58F9500SS) of our Samsung Electric Range and told them about the faulty/dangerous two dual burners. We hated to get close to the range because the burners would turn on if you barely brushed by the range or if you would reach across it and accidentally touch the burner knobs all of a sudden you would feel heat or just see the light indicating the burner was on. We were... Read more

I purchased a new elelmnt and fixed it myself!! Read more

• Gas igniter glows, but will not light
• Little to no heat when baking
• Won't start

The oven would not heat up but the broiler and stove top burners all worked so I replaced the igniter. The part arrived quicker than I expected - one day with regular shipping - and the repair also went much quicker than expected. After accessing the igniter I was able to unplug the plastic modular connection. Instead of pulling the oven out from the wall - which would have been a huge pain - I was able to reach the plug by removing the bottom storage drawer under the oven. From there it was... Read more

• Little to no heat when broiling
• Element will not heat
• Little to no heat when baking

I ordered the bake unit from appliancepartspro.com; while ordering, I decided to go ahead and replace the oven broiler burner as well. Appliancepartspros.com's videos helped me replace the parts with ease. It took barely 30 minutes to install both. Plus, very fast shipping and correct parts. Now, I do not have to worry about baking during Thanksgiving! Cheers, Sean Read more

First i called sears parts direct to order this part, because that is where i purchased my electric range. they had an outrageous price of $98. unbelievable to think that such a small piece of rubber could cost that much. i also called a few other parts dealers on other websites. they also had high prices. when i called appliance parts pros they cut the cost by 50%. i am not sure if i could have found a better price because i stopped there. it is exhausting and time consuming to have to compare... Read more

First, I took an ohm reading across the elements and determined the bad one, which was failed, open circuit. (Zero continuity) I then replaced the lower heating element of the upper oven. Although the design of the oven and element make it appear that it will just drop down and slide out the front, this is not quite the case. There is not enough clearance for it to drop all the way down. You have to pull the entire double-oven unit out of the wall, separate the upper and lower halves a few... Read more

Replacing the Door Gasket is very easy and will take about 2-3 mins per door. Simply remove the Gasket Retainer (1 screw), and pull off the old Gasket. Install the new gasket by simply pushing the gasket clips into the holes where the old clips came out from. Be sure to start gasket at the first hole either side of the Gasket Retainer and work your way around. Reinstall Gasket retainer. The Door Insulation is a very involved repair, and best to follow specific repair manual instructions. Door... Read more

Removed bottom flame cover in lower oven to find the ignitor was actually broken into pieces. We assume it exploded because the bottom side of the cover had a hole blown in it and had to be hammered flat. Before it totally stopped working we had experienced a number of instances where the GFI kicked out when the oven was preheating. Order the GE specific replacement part from Appliance Parts Pros which arrived promptly. The replacement was fairly simple...being careful not to damage the new... Read more

With the help of Wendee and Karen, we finally figured out my model numbers and which parts where correct. I ordered the parts and all arrived the next day except for the Broiler element which arrived in 2 days. I installed the new Baking Element myself. Took longer to figure out which curcuit braker to turn off. In about 30 minutes I had a brand new Baking Element in my oven working perfectly. On the following day, I installed the Broiler Element. That took a bit longer as it sits in a metal... Read more

Replaced burner control switch Read more

Replacing the bad harness switches with the new set fixed the problem. Read more