Washer Accessories

The Drain Hose is an OEM part for Whirlpool washing machines. It is responsible for directing and carrying away water that is pumped out of the washer tub during drain cycles. The drain hose connects from the bottom of the washtub to the household plumbing or out the back of the machine. This washer drain hose includes the retaining clips to hold in place.

Causes of a bad drain hose can include mineral deposits from hard water building up inside the hose, cracking from flexing during use, rodent damage, or general degradation from years of service.

Symptoms of a faulty drain hose include:

• Water not completely draining from the washer tub after cycles
• Puddles or flooding under the appliance
• Strange noises or vibrations during drainage

This part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

STACK KIT FOR LONG VENT DRYER

Includes 2 adhesive pads, 2 brackets, 4 screws, and installation instructions.

This nozzle connector links a water hose to the washer's nozzle/dispenser assembly, creating a tight, leak-resistant connection. Replacing a worn connector helps stop leaks and restores consistent water flow during fill and spray functions. What it does:

• Couples the hose to the nozzle/dispenser assembly and maintains a watertight seal
• Directs water into the dispenser or tub as designed
• Typical failure symptoms: leaks near the top panel or dispenser, loose hose, weak or erratic spray/fill
• Cracking, hardening, or deformation can lead to drips and connection issues

• 1 nozzle connector

• Disconnect power and shut off water supplies before servicing
• Remove the top cover to access the dispenser/nozzle area; protect the work area with a towel
• Release hose clamps, seat the hose fully on the new connector, and secure clamps firmly
• Run a brief fill/rinse to check for leaks before reassembly

Includes two 6 foot fill hoses, 2 Washers, 2 Screens. For a single hose order WP76314

This accessory assembly is the factory-specified kit used to attach or secure designated parts on your appliance. Replacing missing or worn pieces restores a solid, factory fit and finish.

• Provides the original mounting/attachment components specified for your model
• Replaces lost or damaged hardware after installation, moving, or service
• Helps correct loose, misaligned, or rattling parts caused by missing fasteners
• Maintains proper alignment and appearance of exterior parts such as trim or handles

• Disconnect power; also shut off water and/or gas supplies before servicing
• Protect finished surfaces; start fasteners by hand to avoid cross-threading or damage
• Follow your model's service or installation guide for correct order and placement
• After assembly, verify everything is secure and test operation before returning to service

This door reversal kit provides the hardware needed to change the door swing to the opposite side on compatible appliances. Reverse the hinge and strike positions to improve access in tight spaces or match your layout.

• Reverses door swing by relocating the hinge and door strike to the opposite side
• Helps prevent interference with nearby walls, cabinets, or adjacent appliances
• Useful when rearranging a laundry pair or installing in a narrow alcove
• Not intended to repair damaged hinges, latches, or warped doors

• Disconnect power and, if applicable, gas supply before servicing
• Support the door during removal; a second person is recommended
• Move hinge/strike and reinstall fasteners per instructions; avoid overtightening into metal or plastic
• After conversion, verify latch engagement and door seal before use

This stacking kit secures a dryer on top of a compatible washer to save floor space and stabilize the stacked units. It helps keep the dryer aligned and reduces shifting or rocking during use. What it does:

• Provides a secure connection between dryer and washer to create a stable stacked laundry configuration.
• Helps prevent the dryer from sliding, tilting, or shifting during spin cycles — common signs a stack kit is needed.
• Uses brackets and mounting hardware to fasten the dryer to the washer and maintain alignment.

• Disconnect power to both appliances and follow all safety precautions before starting installation.
• Have a second person assist when lifting or positioning the dryer to avoid injury or damage.
• Follow the OEM installation instructions and torque guidance for mounting hardware; ensure both appliances are level and stable after installation.

The Installation Kit is an OEM part for Frigidaire washing machines. It is a kit that provides all the necessary installation hardware to securely mount a washing machine on a pedestal. Having a properly installed and level pedestal is important to ensure stability during the wash cycle and reduce vibration and noise.

Causes may include missing hardware, damaged or worn parts in the existing pedestal, or inadequate installation. This replacement kit from Frigidaire includes mounts, brackets, screws, and leveling components to facilitate a straightforward and proper installation.

Symptoms of a bad or improperly installed pedestal can include:

• Excessive shaking and movement of the washer during operation
• Drain leakage or hose connections coming loose over time
• The washer developing alignment or leveling issues
• Noise and sounds that worsen over repeated use

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This stacking kit secures a compatible dryer to a matching washer to create a safe, space-saving stacked laundry configuration. It helps stabilize the dryer and reduces movement during use for a more reliable setup. What it does:

• Provides brackets and mounting hardware to fasten the dryer to the washer
• Helps prevent the dryer from shifting or tipping when the washer is running
• Improves overall stability of stacked laundry appliances during normal operation
• Reduces vibration-related movement that can cause noise or misalignment

• Disconnect power to both appliances before installing and follow all manufacturer instructions
• Use only on compatible washer/dryer pairs
• Tighten hardware securely but avoid overtightening; follow torque guidance in OEM instructions

This standpipe adapter connects the appliance drain hose to the household standpipe or waste outlet, helping ensure a secure drain path and reduce the risk of leaks or poor drainage. Simple replacement for damaged or worn connectors. What it does:

• Provides a sealed connection between the appliance drain hose and the standpipe or drain outlet
• Prevents water leaks at the hose-to-standpipe junction
• Helps maintain proper drainage and reduces gurgling or slow-draining symptoms
• Durable plastic construction designed to resist cracking and wear under normal use

• One standpipe adapter

• Turn off and unplug the appliance and stop water flow before replacing the adapter
• Remove the old adapter and clean the mating surfaces; ensure the hose and standpipe are free of debris
• Slide the drain hose onto the adapter fully and secure with the proper clamp or retainer
• If you find cracks in nearby hoses or fittings, replace those parts as needed and test for leaks after installation