Washer Housing Or Cover

The Pump Casing is an OEM replacement part for LG washing machines. It is a crucial component that houses the drain pump, which is responsible for removing water from the wash tub during the drain and spin cycles.

Symptoms of a need to replace the pump casing:

• Leaks or water seeping from the pump area
• Unusual noises or vibrations during the drain or spin cycles
• Pump failure or inability to drain water effectively
• Cracks or damage to the casing itself

Causes of a faulty pump casing can include physical impact or mishandling, excessive wear and tear over time, or potential manufacturing defects.

This OEM LG part is also compatible with Sears/Kenmore washing machines.

This is the drain solenoid housing for a dishwasher. It secures and aligns the drain solenoid on the pump assembly so the drain valve actuates consistently and the tub can empty at the right time.

• Positions and insulates the drain solenoid on the pump/drain mechanism
• Maintains proper alignment for reliable drain-valve actuation
• Common symptoms of a failed housing: won't drain or drains intermittently
• May present as loud humming from the solenoid or visible cracks/heat damage on the housing

• Disconnect power and water supply before servicing
• Access the pump area beneath the tub; note solenoid, lever, and linkage orientation
• Transfer the existing solenoid and any clips/brackets to the new housing; reuse fasteners
• Run a short cycle to ensure proper draining after reassembly

This duct outlet directs a dryer's exhaust from the cabinet to the external vent, helping maintain proper airflow and reduce leaks. It replaces a damaged or worn outlet flange to restore safe venting. What it does:

• Channels dryer exhaust from the cabinet to the vent hose or duct
• Helps maintain proper airflow for efficient drying
• Prevents exhaust leaks that can cause poor performance or odors
• Reduces rubbing/interference that can create noise when damaged

• One duct outlet

• Disconnect power before servicing; for gas dryers, turn off the gas supply and disconnect per local codes
• Use basic hand tools; avoid bending the outlet flange to prevent cracks
• Verify a secure seal with the vent hose after installation and test operation

A direct-fit replacement housing that secures and protects internal components, restoring proper alignment and appearance. Replaces a damaged, cracked, or worn housing to help reduce vibration and prevent moisture or debris intrusion. What it does

• Encases and supports internal components to maintain proper fit and positioning
• Helps block moisture and debris from entering sensitive areas
• Reduces vibration and noise caused by loose or damaged housings
• Restores original fit and appearance for panels or assemblies that rely on the housing

• One housing

• Disconnect power to the appliance before starting any repair
• Handle part carefully to avoid scratching or cracking during installation
• Basic hand tools are typically required; follow OEM instructions for fastener locations and torque
• Recheck fit, seals, and alignment after installation; replace any damaged fasteners or gaskets as needed

This pump access shroud is the molded access cover that houses and protects the washer pump and nearby plumbing, keeping components contained and helping direct drained water to the pump. It restores the factory routing and protection for pump area. What it does:

• Covers and protects the washer drain pump and surrounding hoses from debris and direct contact
• Helps direct water flow into the pump for proper drainage
• Reduces risk of water reaching electrical components behind the pump area
• Can resolve symptoms such as water pooling around the pump area or visible routing damage near the pump

• One pump access shroud

• Disconnect power and water supply before beginning any service
• Access may require removing the washer cabinet or rear/front service panel and lifting or tipping the machine per the model's service instructions
• Handle plastic shroud carefully to avoid breaking mounting tabs; use proper replacement clips or fasteners if original hardware is damaged
• Secure all hose and pump connections before testing the appliance

This pump access shroud is the replacement housing that protects and encloses the washer pump area, helping keep pump components aligned and shielding them from debris. It restores proper coverage around the drain pump assembly. What it does:

• Provides a protective enclosure for the washer drain pump and related fittings
• Helps prevent debris from contacting the pump and impeller
• Restores correct fit and alignment of pump components after damage or wear
• Can reduce gap-related leaks and rattling caused by a cracked or broken shroud

• Disconnect power and shut off water before beginning work
• Drain any remaining water from the tub or hoses to avoid spills
• Access typically requires removing the washer cabinet or front panel; follow your model's service manual
• Handle plastic components carefully to avoid cracking; replace damaged fasteners as needed

This diverter box top directs dishwasher wash water to the upper spray arm so dishes on the top rack get cleaned. It replaces a worn or cracked diverter to restore proper spray distribution and reduce leaks. What it does:

• Routes wash water from the pump to the upper spray arm during the cycle
• Helps maintain correct spray pressure and coverage for top-rack cleaning
• A cracked or clogged diverter can cause poor upper-rack cleaning or water spraying irregularly
• A damaged diverter may allow leaks or reduce wash performance

• One diverter box top

• Disconnect power and turn off water supply before servicing
• Remove the dishwasher tub or access panels as required to reach the diverter; basic hand tools typically required
• Inspect surrounding seals and gaskets during install; replace if they show wear