Washer Endcap Parts

This trim piece finishes and protects an opening or edge on your appliance's cabinet or console. Replacing a cracked or missing trim restores a clean, factory look and helps nearby components sit and operate as intended. What it does:

• Provides a clean, finished edge and covers sharp cabinet/console edges
• Helps keep adjacent parts aligned and secured around the opening
• Restores appearance when original trim is cracked, warped, discolored, or missing
• Common symptoms: loose or rattling piece, cosmetic damage, snagging edges, or poor fit of nearby parts

• 1 trim piece

• Disconnect power; if applicable, shut off gas or water. Wear cut-resistant gloves.
• Remove the existing trim by releasing clips or removing screws; note orientation and retain hardware.
• Transfer any reusable clips/inserts from the old trim to the new part.
• Align and snap/screw the new trim into place; do not overtighten.

Replacement end cap that restores the appliance's finished edge and helps protect internal components from debris. A simple, low-cost repair to replace cracked, broken, or missing end caps and reduce trim wear. What it does:

• Covers and protects an exposed edge or end of the cabinet/trim.
• Helps prevent snagging, dirt buildup, and contact damage where the cap is missing or cracked.
• Restores the appearance and alignment of surrounding trim pieces.
• Common symptom: visible crack, loose or missing trim, rubbing or catching at the edge.

• Disconnect power and/or water supply to the appliance before beginning work when applicable.
• Inspect the mating surface and remove old adhesive or fasteners before installing the replacement cap.
• Install by aligning the cap and snapping or fastening into place; do not force—use correct fasteners if applicable.
• If surrounding trim is damaged, consider replacing affected pieces to ensure proper fit and finish.

Note: END CAP KIT CONTAINS (1) RH. & (1) LH. CAP

This right-side end cap is a replacement trim/closure piece designed for the washer cabinet to restore proper fit and finish and help keep internals protected from debris. It replaces a damaged, cracked or missing end cap. What it does:

• Covers and protects the washer's right-side edge or mounting area from dust and moisture
• Restores a flush appearance where the original end cap was cracked or broken
• Helps prevent snagging on clothing or towels from a damaged trim piece
• Can reduce rattles or vibration caused by a loose or missing end cap

• Disconnect power to the appliance before beginning any work
• Usually secured with screws or clips; basic hand tools are typically all that's required
• Align the part to the right-side mounting location and fasten securely without over-tightening

White. Right had side

Black. Right hand side

This left-hand end cap is a direct-fit replacement part that helps secure the washer's left-side assembly and restores proper cabinet/drum alignment for smoother operation and reduced vibration. What it does:

• Caps and protects the left-side end of the washer assembly to prevent wear and debris entry
• Helps maintain proper alignment of the washer drum/cabinet on the left side
• Reduces noise, rubbing, or wobbling caused by a damaged or missing end cap
• Matches OEM fit and mounting points for straightforward replacement

• Disconnect power and water to the washer before starting any repair
• Basic hand tools may be required; some disassembly of the cabinet or front panel could be needed
• Inspect adjacent components (gaskets, seals, fasteners) for wear while replacing the end cap

This right-side end cap fits the dryer's drum assembly and restores proper alignment and support for smooth, quiet operation. It replaces a worn or damaged end cap to reduce drum wobble and related noise. What it does:

• Supports and positions the drum at the right end to maintain proper rotation
• Helps prevent rubbing, scraping, or metal-on-metal contact that can cause noise
• Restores secure mounting for associated rollers/bearings at the right side
• Can be replaced when the end cap is cracked, broken, or visibly worn

• One right-side end cap

• Disconnect power to the appliance before beginning any repair
• Access typically requires removing the dryer front panel or bulkhead
• Inspect related rollers, bearings, and mounting hardware; replace any worn parts to prevent repeat failure
• Reassemble panels and verify the drum spins freely and without unusual noise

White. Left hand side