White Westinghouse Washer Dryer Combo Parts

• Takes too long to dry

Get some acetone at a Hardware Store before you start. A pint will do. Unplug the dryer from 110 VAC. Pull the top off of the dryer, by lifting it from the front first. It is attached with snap metal fittings. Do not completely remove the top, just tip upright to gain access to the front interior of the dryer. Before you pull any wires from the door switch, record which color wires go to which terminals on the door switch. If you reassemble the connections incorrectly, the gas value will... Read more

Main problem was worn bearings in the motor, which was replaced. Additional issues were worn pulley on tensioner and impeller slipping on motor shaft. Pulley was replaced and hose clamp was used to secure blower on shaft. Read more

I replaced the spin bearing, tub seal, washer and drive belt since I had it all apart. The video was extremely helpful...I would have tore the whole thing apart trying to figure out how the agitator came off....but it was very simple. Read more

The blower wheel center was worn down and spinning freely on shaft. Removing front covers, controls and brackets gave access to blower, which front half came off removing screws. (One screw underneath bracket) Pushed new blower on. (It's keyed and has small tabs that line up with groove on shaft). Installed clamp, reassembled and tested. Don't forget to pull the plug out before working on any appliance. Read more

I went online, ordered the part and installed it,,, took 15 minutes to install,,,saved huge $$$ easy peasy!! :-) Read more

I used the internet and checked a dry fuse, and it tested ok. Checked the start switch, ok. So it had to be the motor. Sharon at the company agreed. Motor, and belt arrive very fast. ordered the belt because, if I had it apart why not change it. Internet also helped get the dryer apart. Found on u-tube a repairman cut a hole in the side to gain easy access. This dryer is not easy to work on, but this helped, and will make further repairs much easier. Using the internet, and... Read more

• No hot or cold water
• Will not stop filling with water
• Will not fill with water
• Leaking

This is my third repair of this type. The first was a stand-alone washer and was very easy, because there was a plate on which the inlet valve assembly was mounted, and it was easily removed. This repair was on a Frigidaire stacked washer/dryer (laundry center). Stacked washer/dryers are typically purchased to save space and are often tucked into a closet. Be sure you can pull it out to access both front and rear. Remove drain hose from drain, detach water hoses, electricity and dryer vent... Read more

• Door won't close

My dryer door would not stay shut because the door strike was stuck in the door catch. I was afraid that when I pulled the strike out, it would damage the catch, so I ordered the door strike and door catch. I got the damaged door strike out with needle nosed pliers in about 15 seconds. The door catch was in perfect condition so I didn't need to use the one I ordered. So then I proceeded to install the new door strike. That took me about 15 minutes because I did not have the manual strength to... Read more

Replaced springs and shocks. Read more

The old knob was not repairable. I ordered a new knob for the washer dryer stack unit. The order came within two days of ordering and it was the correct part. I was pleased. Read more

I went online, ordered the part and installed it,,, took 15 minutes to install,,,saved huge $$$ easy peasy!! :-) Read more

• Timer will not advance

I replaced the timer Read more

Our washer is next door the bathroom. So when, during the rinse cycle, the hose split and we found the back of the house completely flooded I initially assumed the culprit was either the toilet or the sink or possibly an interdimentional portal into a demonic netherworld of vaguely chlorine scented water. I spent the next hour mopping it all up and checking and re-checking the pipes in the bathroom with no apparent leaks. The next load of laundry left more clues as this time the flood was from... Read more

I watched the helpful diy video. It gave me what the problem was and the confidence to do it. Took my dryer apart with the helpful hints in the video repair went smooth. Works like a dream and I saved money. Thank you appliance parts pros. Read more

I looked on Appliance Parts Pros. com and read the problems that others had and replacing the ignitor made sense so I ordered one. It came by UPS within 3 days. I watched the video on how to replace it. Everything went easily, except the screw that held the ignitor in place was a philups head screwdriver and I couldn't get a screwdriver into the small space I had to work in so I went to Harbor Freight Tools and bought an inexpensive 90 degree rachet screwdriver for $2.99 and it worked great.... Read more

Pushed new knob on Read more