Whirlpool Cap Or Cover

This replacement cover shields and finishes a designated area of your appliance, protecting internal components from dust, moisture, and accidental contact. Replace a cracked or missing cover to maintain proper operation and a clean, finished look.

• Protects internal parts from debris and moisture intrusion
• Restores intended airflow/containment and component protection
• Helps reduce rattles or vibration from loose or broken trim
• Common signs it's needed: cracks, broken tabs, loose fit, or exposed components

• Disconnect power; also shut off water supply
• Retain and reuse original screws/clips unless your model specifies otherwise
• Align tabs and mounting holes carefully to avoid stress on plastic
• Do not overtighten fasteners; snug by hand to prevent cracking

The Hinge-Sleeve Hole Plug is an OEM part for Whirlpool refrigerators. It is designed to cover the hinge sleeve holes on the refrigerator door, providing a finished look and protecting the internal components from dust and debris.

Common causes of a bad hinge-sleeve hole plug include physical damage during routine maintenance or accidental impacts. A missing or damaged plug can lead to exposure of internal hinge components, potentially causing further damage over time.

Symptoms of a bad hinge-sleeve hole plug include:

• Visible gaps or holes in the refrigerator door hinge area
• Accumulation of dust or debris in the hinge mechanism
• Loose or unstable refrigerator door hinges

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This water filter cap secures the refrigerator's water filter inside its housing and provides a handhold for easy removal. Replace a cracked or missing cap to maintain a proper seal and help prevent leaks during filter changes.

• Locks the filter into place for a tight, reliable seal
• Provides grip to twist the filter in and out of the housing
• Helps prevent drips at the filter connection
• Common symptoms: cap cracked or missing, hard-to-turn filter, filter won't stay seated, or water leaking from the filter area

• Turn off the water supply and dispense water to relieve pressure
• Place a towel under the filter area to catch any residual water
• Remove the old cap by turning it counterclockwise; attach the cap to the filter end
• Insert the filter/cap assembly, align tabs, and turn until it stops—hand-tight only; restore water and check for leaks

This protective cover shields and guides the appliance's water line at the back, helping prevent kinks, abrasion, and vibration. Replacing a damaged or missing cover helps protect the tubing and supports consistent water flow. What it does:

• Protects and routes the water supply tubing to reduce rubbing and wear
• Helps prevent kinks or pinches that can restrict water flow
• Keeps the line secured to minimize vibration and rattling
• Common signs include a cracked/missing cover, exposed/kinked tubing, leaks, or reduced water flow

• 1 water hose cover

• Disconnect power and shut off the water supply before servicing
• Pull the appliance forward for access; remove any screws/clips securing the old cover
• Note the tube routing; install the new cover without pinching the line
• Restore water and power, then check for proper flow and any leaks

This washer lid assembly replaces a cracked, broken, or misaligned lid so the washer can close and lock correctly, restoring safe operation and reducing cycle interruptions caused by a lid that won't align or latch.

• Covers the tub opening and aligns with the lid lock/strike for proper engagement
• Restores the safety interlock so wash cycles can start and run without interruption
• Helps contain splashing and keeps debris out of the washer when not in use
• Typical symptoms include visible cracks or shattering, warped or loose lid, broken hinge area, or intermittent lid-lock errors

• Disconnect power before servicing
• Protect the cabinet surface and support the lid during removal/installation to prevent damage
• If required by your model, transfer existing hinge hardware and fasteners to the new lid
• After installation, check alignment and ensure the lid lock engages smoothly before running a cycle

Restore the clean look and proper function of your washer's detergent compartment with this detergent dispenser drawer cover. It replaces a cracked or missing cover so the drawer closes correctly and helps reduce splashing at the dispenser. What it does:

• Covers and protects the front of the detergent dispenser drawer
• Helps the drawer align and close properly for consistent dispensing
• Replaces broken or missing cover tabs that prevent the drawer from staying in place
• Common symptoms: cracked/missing cover, broken tabs, drawer won't close or feels loose, splashing/leaks at the dispenser area

• 1 detergent dispenser drawer cover

• Unplug the appliance and shut off water supply before servicing
• Pull the dispenser drawer out and depress the release tab to remove it
• Release the locking tabs to remove the old cover; snap the new cover fully into place
• Reinstall the drawer and run a quick test to check operation

This replacement pusher fits the refrigerator's ice dispenser/ice-bucket assembly and helps drive the mechanism that moves ice through the chute. Replacing a worn or broken pusher restores smooth, reliable ice dispensing.

• Engages the dispenser/crusher linkage to advance ice from the bucket toward the auger and chute
• Supports crushed/cubed selection on models equipped with that feature
• Wear or breakage can cause weak or no dispensing, jamming, or being stuck in one mode
• Visible cracks, deformation, or missing plastic are common failure signs

• Disconnect power to the refrigerator; remove the ice bin
• Access the ice bucket/dispenser mechanism and note the original pusher's orientation before removal
• Reuse existing screws/clips as needed and confirm the mechanism moves freely after installation
• Reinstall the bin, restore power, and test both cube and crush dispense modes

This replacement cover restores the appliance's finished appearance and protects internal components from dust and debris. It's a direct-fit exterior trim piece designed to replace a cracked, broken, or missing cover. What it does:

• Protects internal components and wiring from debris and accidental contact
• Restores the appliance's cosmetic appearance and helps maintain sealing
• Helps reduce dust buildup in the covered area
• Replaces damaged or missing trim that can expose sharp edges or hardware

• Disconnect power (unplug or switch off circuit breaker) before beginning work
• Basic hand tools may be required; follow for panel removal/replacement
• Handle carefully to avoid scratching the finish and watch for sharp edges
• Replace with manufacturer-recommended fasteners

This emitter cover is the molded housing that shields and positions the infrared emitter for the refrigerator's ice level optics. Replacing a cracked or missing cover helps protect the board and keep the beam path clear for reliable ice making. What it does:

• Shields the emitter board and lens from moisture, frost, and debris
• Aligns the infrared beam path across the ice bin to the receiver
• Helps secure and position the ice level optics assembly
• Common symptoms: broken/missing cover, intermittent or no ice production due to optics misalignment or obstruction

• 1 emitter cover

• Disconnect power to the refrigerator before servicing
• Remove the ice bin to access the optics components
• Release the old cover's retaining tabs or fastener and lift it off; avoid touching board components
• Position and secure the new cover, then restore power and test ice maker operation

This pusher is a small mechanical component that transfers motion and keeps mating parts aligned within its assembly. Replacing a worn or broken pusher restores smooth travel and reliable engagement so the mechanism operates as designed. What it does:

• Transfers motion to a lever, switch, or linkage to initiate movement
• Helps maintain alignment and smooth, repeatable travel of mating parts
• Restores proper engagement to reduce sticking or binding
• Typical signs it's failing: cracked or missing piece, intermittent operation, excessive force needed, or visible wear

• Pusher only

• Disconnect power; turn off water supply before servicing
• Access the assembly and note the pusher's orientation; take a reference photo
• Transfer any springs/clips from the original and securely seat the new part
• Manually check for free movement before reassembly and test operation

This hinge cover assembly conceals and protects the door hinge area, providing a clean look while shielding wiring and moving parts from dust and moisture. It restores proper coverage if the original cover is cracked, missing, or loose.

• Covers the hinge area to protect components and improve appearance
• Helps prevent debris intrusion around the hinge mechanism
• Common fix for a broken, missing, or damaged hinge cover
• May help if the hinge area is exposed or rattling due to a loose cover

• Unplug appliance before service; shut off water if applicable
• Use a non-marring tool to release clips or tabs; avoid prying on finished surfaces
• Transfer any reusable screws or trim from the old cover
• Confirm secure engagement of tabs/screws to prevent vibration

This thermistor cover shields and positions the refrigerator's temperature sensor so it reads cabinet air accurately. Replacing a cracked or missing cover helps restore stable temperatures and normal cooling performance.

• Holds the thermistor in place and shields it from direct airflow for accurate temperature sensing
• Helps prevent erratic temperatures, overcooling/undercooling, or long run times caused by an exposed sensor
• Commonly replaced when the original cover is cracked, loose, or missing
• Supports consistent temperature control by ensuring proper sensor placement

• Disconnect power before servicing
• Remove shelves/bins as needed to access the sensor location
• Align the thermistor and seat the cover fully; engage tabs or reuse existing hardware per model
• Avoid pinching the sensor or wiring and verify the cover is snug

This cover replaces a cracked, warped, or missing cover on your appliance. It protects internal components and restores the correct fit and finish so parts stay secured and the unit operates as designed.

• Shields internal components from debris and moisture
• Helps maintain proper airflow, water path, or guarding as designed
• Restores fit/finish and keeps parts secured
• Common signs of failure: cracks, broken tabs, discoloration, or a cover that won't stay in place

• Disconnect power and shut off water/gas before servicing
• Note the original orientation and transfer any screws/clips from the old part
• Align tabs and fasteners; avoid overtightening to prevent damage
• After installation, test operation and ensure no interference or leaks

This dryer blower cover encloses the blower wheel and seals the housing so air moves efficiently from the lint screen to the exhaust. Replacing a cracked or missing cover restores airflow for consistent drying performance and helps keep lint contained.

• Covers the blower wheel and seals the blower housing
• Directs air from the lint screen through the exhaust duct
• Helps maintain proper airflow and drying performance
• Damage or gaps may cause reduced airflow, longer dry times, vibration/noise, or lint leaking inside the cabinet

• Unplug dryer and let components cool before servicing
• Access the blower housing; front or rear access varies by model
• Clean lint from housing and ducts; inspect the blower wheel and any gasket/seal
• Seat cover squarely and tighten fasteners evenly; verify the blower turns freely and no air leaks are present

This small plug seals and finishes an unused factory or service hole on the appliance cabinet or liner. It restores a clean, finished appearance and helps keep dust and splashes out of the opening. What it does

• Closes an open hole on the cabinet/liner or panel
• Helps reduce entry of debris and incidental moisture into the opening
• Maintains a neat, finished look
• Replace if the original plug is missing, cracked, or won't stay seated

• 1 plug

• Disconnect power before servicing; shut off water supply if working near water lines
• Identify the correct opening per your model's parts diagram
• Remove any remnants of the old plug; clean the area
• Align and press the plug fully into the hole until it sits flush—do not force or deform the panel

The Cap Filter is an OEM component for Whirlpool refrigerators. Located inside the back of the fresh food compartment, it helps maintain optimal indoor air quality by capturing household odors and gases.  

The precision-woven filter media effectively removes ethylene and other contaminants from circulating air without slowing airflow. Its secure mounting design installs and removes easily without tools for periodic replacement.

Causes of a faulty cap filter include clogging from accumulated particles or moisture remaining trapped over time, which reduces effectiveness.

Symptoms of a bad cap filter can include: 

• Lingering odors inside the refrigerator  
• Fresher items absorb smells faster than usual
• Decreased airflow causing warmer temperatures
• Small pieces of filter shedding inside

Replace yours today with this genuine Whirlpool filter to restore maximum odor protection. Compatible with many Kenmore, Maytag, Jenn-Air, and KitchenAid models.