Whirlpool Dishwasher Dispenser Parts

This dispenser assembly replaces a refrigerator's door-mounted ice and water dispenser to restore normal dispensing and reduce leaks or delivery issues. It provides the core housing and user-facing dispenser opening for door-based dispensing systems. What it does:

• Directs water and ice from the door dispenser to the user, forming the visible dispensing opening and housing.
• Helps stop common dispenser symptoms such as water dripping from the dispenser opening or ice/jam buildup at the dispenser chute.
• Supports normal push-lever or paddle operation and routes water/ice to the exterior dispense area.

• Disconnect power and shut off the water supply before starting any work.
• Removal typically requires taking off the refrigerator door panel or trim to access mounting fasteners—retain all hardware and note fastener locations.
• Handle the dispenser housing carefully to avoid cracking plastic or damaging seals; inspect gaskets and fittings and replace if brittle.

This dispenser stores the detergent and rinse aid and releases them at the proper time during the cycle, helping your dishwasher clean effectively and reduce spotting. Replacing a faulty dispenser restores consistent soap release and rinse performance. What it does:

• Holds detergent and rinse aid, then opens to release them at the correct stage of the wash
• Helps prevent detergent remaining in the cup after a cycle
• Restores proper latching and sealing of the dispenser door
• Common fix for a cracked housing, broken latch, or rinse aid leaking/over-dispensing

• 1 dispenser assembly

• Disconnect power to the dishwasher before servicing
• Remove inner door panel fasteners to access the dispenser; disconnect the electrical connector
• Release the locking tabs, remove the old dispenser, and seat the new one evenly to ensure a proper seal
• Reassemble the door, restore power, and run a short cycle to check for leaks and proper operation

This dispenser is the door-mounted assembly that delivers ice and/or water from the refrigerator. It replaces a worn, cracked, or malfunctioning dispenser to restore normal dispensing and stop leaks. What it does:

• Provides a finished dispenser opening and support for the actuator and chute so water and ice flow correctly.
• Stops leaks and prevents food or debris from entering the dispenser area when cracked or damaged.
• Restores proper activation when the dispenser lever or paddle no longer engages the valve or auger.
• Helps eliminate jams or misalignment that can cause intermittent dispensing or noisy operation.

• Disconnect power and shut off the water supply before starting any work.
• Remove the inner door panel or trim to access the dispenser mounting screws and wiring.
• Handle gently to avoid cracking surrounding trim; test operation before reassembling the door.

This is the lid assembly for the dispenser. It covers and protects the dispenser compartment, helping keep debris out and ensuring the dispenser opens and closes properly.

• Covers the dispenser compartment to prevent spills and contamination
• Helps ensure proper dispenser operation
• Common fix when the dispenser lid is cracked, broken, loose, or won't stay closed

• Disconnect power and shut off water before servicing
• Open the dispenser area and remove any retaining screws or tabs
• Transfer any reusable hardware from the old lid to the new assembly
• Test operation before returning the appliance to service

This replacement cover restores the appliance's exterior protection and appearance by shielding internal components and helping maintain safe operation. Designed to match the original form and mounting points for a direct-fit replacement. What it does:

• Shields internal parts from dust, spills and accidental contact.
• Helps keep wiring and controls securely enclosed to reduce risk of damage.
• Restores a flush, finished exterior when the original cover is cracked, broken or missing.
• Prevents rattling or snagging caused by loose or damaged panels.

• Disconnect power (unplug or shut off breaker) before starting any work.
• Installation typically requires basic hand tools (screwdriver/socket); follow factory service instructions for fastener locations.
• Handle edges carefully—parts may have sharp edges; support the panel during removal/installation to avoid scratches or dropped hardware.
• Reinstall all fasteners snugly but avoid over-torquing; verify panels align and clear moving parts before restoring power.

This bi-metal is the thermal actuator that releases the detergent dispenser at the proper point in the wash cycle. Replacing a weak or failed actuator restores reliable detergent cup opening and consistent detergent delivery for better cleaning. What it does:

• Heats and flexes when energized by the control to trip the dispenser latch
• If failed, the detergent cup may not open or may open inconsistently
• Can leave detergent in the cup and lead to poor cleaning results
• Often suspected when the cycle runs but the soap door stays closed

• 1 bi-metal actuator assembly

• Disconnect power at the breaker before servicing
• Remove the inner door panel to access the dispenser area
• Note wiring positions and orientation; transfer connectors securely to the new actuator
• The dispenser latch/linkage moves freely and test door release before reassembly

This wet agent dispenser replaces the washer's liquid fabric softener dispenser to restore proper dispensing during the rinse cycle. It helps keep softener contained until the machine is ready to release it, improving rinse-time performance. What it does:

• Holds and releases liquid fabric softener (wet agent) into the rinse cycle
• Ensures softener is delivered at the correct time for even distribution
• Stops leaking or premature release when the dispenser housing is intact
• Commonly replaced when the dispenser cracks, clogs, or fails to dispense

• Disconnect power to the appliance before starting any repairs
• Access method varies by model; remove dispenser drawer or top panel per your model's service instructions
• Inspect surrounding seals and clips; replace if damaged to prevent leaks

This replacement housing restores the appliance's structural enclosure, protecting internal components and helping panels and controls align properly. Use it to replace cracked, warped or damaged housings so the unit fits and functions as intended. What it does:

• Provides the main structural enclosure and mounting surface for internal components and exterior panels
• Replaces cracked, dented or broken housings that can allow misalignment or rubbing of parts
• Helps reduce vibration and movement by restoring proper fit between panels and internal assemblies
• Keeps internal components shielded from debris and wear that can lead to downstream issues

• Disconnect power (and water, if applicable) before starting any repair
• Handle edges carefully; housing edges and sheet metal can be sharp
• Basic hand tools are typically required; follow the appliance service manual for disassembly/reassembly steps

This wet agent dispenser assembly holds and releases liquid wetting/conditioning agents into the wash at the correct cycle, helping deliver fabric conditioner or similar additives when needed. It replaces a worn, clogged, or damaged dispenser for reliable delivery. What it does:

• Holds liquid fabric conditioner/wetting agent and releases it into the tub during the rinse cycle
• Ensures timed dispensing so conditioners are added at the proper point in the cycle
• Helps prevent over-dispensing and visible residue in the washer tub or on clothes
• Commonly replaces dispensers that leak, fail to release liquid, or have broken mounting tabs

• One wet agent dispenser assembly

• Disconnect power to the appliance before beginning any work
• Remove and reinstall using basic hand tools
• Rinse any remaining liquid from the area and avoid skin/eye contact with chemicals
• Test a short cycle after installation to ensure proper dispensing and secure mounting

Also order retainer part number WP3400918

The Thermostat Housing is an OEM part for Whirlpool dishwashers. It encases the thermostat responsible for accurately monitoring water temperatures throughout cleaning cycles. 

Symptoms of a faulty housing include:

• Inconsistent or improper water heating  
• Delayed or incomplete cycles from temperature control issues
• Error codes or failure detection by the control board

Causes may involve cracks allowing steam penetration, loose mounting points compromising seals, or damaged seals leaking interior thermostat components. 

This OEM replacement fits Whirlpool, KitchenAid, Jenn-Air, and some Kenmore models as well.

This dispenser is the front housing that channels ice and water from the refrigerator to the user, restoring proper dispensing and a finished appearance. It fits into the refrigerator door and works with the dispenser controls. What it does:

• Directs and channels ice and water from the internal supply to the exterior dispenser opening
• Provides the mounting surface and openings for dispenser controls, actuator/lever, and chute
• Helps prevent leaks and misdirected water when the dispenser is working correctly
• Commonly replaced for cracked housing, broken mounting tabs, or cosmetic damage that affects dispensing

• One dispenser housing assembly

• Disconnect power and turn off the water supply before starting any repair
• Handle plastic clips and tabs carefully during removal to avoid breakage
• Reuse any electronic components only if compatible; replace damaged clips or seals
• After installation, turn on water and power and check for proper operation and leaks

The Tank is an OEM part for Whirlpool washing machines. It properly dispenses detergent during the wash cycle.

Causes of a bad detergent tank can include: cracks, holes or other damage that cause leakage or improper detergent dispensing. Scaling or mineral buildup inside the tank over time may also lead to detergent dispensing issues.

Symptoms of a bad detergent tank include:

• Detergent not being fully dispensed or released during the wash
• Residue or leftover detergent remaining in the tank after cycles
• Clothes not getting properly cleaned due to insufficient detergent release

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Detergent Dispenser Assembly is an OEM part for Whirlpool dishwashers, designed to store and release detergent and rinse aid at the appropriate times during the wash cycle. This component ensures that your dishes are cleaned efficiently by dispensing the correct amount of detergent for optimal washing performance. 

Causes of a malfunctioning dispenser can include mechanical failure of the latch or spring mechanism, clogging due to detergent buildup, or electrical issues preventing the dispenser from operating correctly.

Symptoms of a bad Detergent Dispenser Assembly include:

• Detergent not being dispensed correctly, leading to poorly cleaned dishes.
• The dispenser door not opening during the cycle or failing to latch properly before starting.
• Leakage of detergent from the dispenser, indicating a seal failure.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.