Whirlpool Dishwasher Panel Parts

The Dishwasher Access Panel is an OEM part for Whirlpool dishwashers. This panel covers the lower front section of the dishwasher, providing a finished look while protecting internal components from debris and damage.

Causes of a bad access panel include accidental impacts, wear and tear over time, or exposure to moisture, which can lead to rust or corrosion.

Symptoms of a bad access panel include:

• Visible cracks or dents
• Rust or discoloration
• Loose or misaligned panel

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This replacement panel restores your appliance's original look while shielding internal components. Install a new panel to replace a dented, cracked, or missing piece and keep the assembly secure, aligned, and protected.

• Covers and protects internal parts while restoring the exterior finish and fit
• Provides the designed mounting surface for trim/handles; helps maintain alignment
• Replace when the panel is dented, cracked, warped, rusted, or mounting tabs are broken
• Helps resolve loose or rattling panels and visible gaps or misalignment

• Disconnect power; turn off water or gas supply if applicable
• Wear gloves and protect finished surfaces; handle carefully to avoid bending or scratching
• Transfer and reuse original screws, clips, insulation, and trim as directed by your service manual
• Fit and alignment before fully tightening fasteners

The Control Panel is an OEM replacement part for Whirlpool built-in dishwashers. It is the control panel located on the front façade, comprising buttons to select cycles and indicator lights showing progress. This interface allows for efficient operation through simple input of wash selections. 

Causes of a failing control panel involve damage to electronic components from moisture exposure over time. Wiring degradation or faulty circuit boards can also disrupt intended functions.

Symptoms of an inadequate control panel include:

• Unresponsive buttons that do not initiate cycles  
• Light indicators that do not illuminate properly
• Erratic or unexpected dishwasher behavior

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Water Level Switch Bracket is an OEM part for Whirlpool dishwashers. This bracket holds the water level switch in place. The water level switch is a part that monitors and regulates the amount of water inside the dishwasher.

Causes of a bad Water Level Switch Bracket can include physical damage that may occur during use or installation, corrosion over time due to exposure to moisture and detergents, or general wear that compromises its ability to securely hold the water level switch.

Symptoms of a bad Water Level Switch Bracket include:

• The dishwasher not filling with the correct amount of water
• Water leaking from the dishwasher if the switch moves out of position and fails to regulate the water level accurately.
• Unusual noises during the fill cycle

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Panel (BLK) is an OEM part for Whirlpool dishwashers. This black exterior panel is designed to provide a sleek and durable front surface for the dishwasher, enhancing its appearance and protecting internal components.

Causes of a bad panel can include physical impacts, scratches, or general wear over time. A compromised panel can affect the aesthetic appeal and may expose internal components to potential damage.

Symptoms of a bad panel include:

• Visible dents, scratches, or cracks
• The panel not fitting securely or aligning properly
• Discoloration or fading of the panel surface
• Difficulty opening or closing the dishwasher door

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Color: Black. Other colors: For white use WP3369614.

Color: White

This is the lower access panel for the appliance's base. It finishes the front opening and shields internal components, helping reduce noise and keep dust and debris away from the motor and wiring.

• Covers the lower service opening beneath the door to provide a clean, finished look
• Helps protect internal components from debris and accidental contact
• Can reduce vibration noise when properly secured
• Replace if the panel is bent, cracked, rusted, missing, or rattles/doesn't stay secured

• Disconnect power; also shut off the water supply
• Support the existing panel while removing mounting screws; retain hardware for reuse
• Position the new panel, align with mounting holes/slots, and reinstall screws—do not overtighten
• Confirm door clearance and that the panel sits flush without interference

This control panel mounts on the appliance's door and provides the push-button interface for selecting cycles and options. Replacing a cracked or unresponsive console restores reliable button operation and a clean, factory look. What it does:

• Houses the user-interface buttons and indicator windows used to select cycles/options
• Provides a rigid mounting surface for the door's UI components
• Helps protect internal wiring at the top of the door
• Typical symptoms: buttons don't respond or work intermittently, unit won't start when Start/Resume is pressed, selections change unpredictably, or the console is cracked/loose

• One console assembly

• Disconnect electrical power; turn off the water supply if needed
• Open the door and remove the inner-door perimeter screws to separate the console from the inner panel
• Note and transfer any reusable parts from the old console as required; make secure, straight ribbon/harness connections
• Reassemble the door, restore power, and run a quick function check before final tightening

The Dishwasher Front Door Panel is an OEM part for Whirlpool brand dishwashers. Forming the outer surface of the door, this stainless panel provides a protective barrier and the surface for mounting handle components. 

Causes of a bad front door panel can include damage from repetitive closure stresses, impacts from loaded dishes, or cracks developing from regular cleaning chemicals.

Symptoms of a bad front door panel include:

• Cosmetic damage detracting from appearance
• Obstructions preventing proper latching of the door  
• Leaks forming at the door gasket sealing surface

This OEM replacement is compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore models. 

Color: White. Includes insulation. Other colors: For almond use WP3384157, for biscuit use WP3384157, for black use WP3379920.

This replacement access panel restores the finished look at an appliance service opening and keeps internal components protected from dust and debris. Use it when the factory panel is cracked, dented, loose or missing. What it does:

• Covers the appliance access/service opening to protect wiring and components from dust and accidental contact.
• Restores the exterior appearance where the original panel is cracked, dented or broken.
• Helps reduce drafts and keeps small objects out of the service cavity.
• Provides a correct replacement part for repair or cosmetic restoration when the original panel is damaged or missing.

• Disconnect power to the appliance before removing or installing the panel.
• Removal/installation typically requires basic hand tools (screwdriver or nut driver) to release screws or clips—do not force fasteners.
• Align panel tabs/clips and secure with the original hardware.

This caster support wheel helps restore smooth movement and stable support for the appliance's cabinet or drawer assembly. It replaces a worn or damaged wheel so the part rolls and aligns correctly. What it does:

• Replaces a worn or broken caster wheel that prevents smooth rolling
• Restores proper support and alignment for drawers or appliance base panels
• Reduces catching, scraping, or noisy movement caused by damaged rollers
• Helps maintain consistent front-to-back leveling when used with leveling hardware

• One caster support wheel

• Designed for basic drop-in replacement; position part where existing caster was mounted
• Turn off power and remove food/items or shelves from the cabinet/drawer area before working
• Use appropriate hand tools; avoid over-tightening fasteners which can bind the wheel

This outer dishwasher door panel restores the appliance's front appearance and provides a finished, protective surface for the door. Fits replacement needs where the original panel is scratched, dented, or cosmetically worn. What it does:

• Replaces the outer door surface to restore the dishwasher's exterior finish and color
• Covers and protects internal door components from everyday wear
• Helps maintain a flush, sealed appearance around the door edge
• Addresses symptoms such as visible dents, deep scratches, paint wear, or detached/loose outer door skin

• Disconnect power to the dishwasher before beginning any service
• Exterior trim, handle, or insulation may need to be removed or transferred during installation
• Support the door when loosening fasteners to prevent dropping or damage
• Follow the manufacturer's service instructions for proper alignment and torque of door hardware

Color: Black

This replacement mixer pedestal restores the base support and appearance of compatible stand mixers, providing a stable platform and finished look. Use it to replace cracked, chipped, or damaged pedestals that affect mixer stability. What it does:

• Replaces a worn or damaged pedestal to help stabilize the mixer and reduce wobble
• Restores the exterior finish where the original pedestal is cracked, chipped, or broken
• Provides the proper mounting surface for the mixer head and internal components
• Helps prevent further wear or damage caused by an unstable base

• One mixer pedestal (white)

• Disconnect power and remove the mixer from any mounting before attempting replacement
• Follow OEM disassembly steps for accessing and removing the pedestal; keep fasteners for reinstallation
• Use basic hand tools; avoid forcing parts and protect finished surfaces from scratches