Whirlpool Dishwasher Parts

Color: Black. Instruction sheet included.

This is the upper spray arm that distributes wash water to the top rack. Replacing a cracked, warped, or clogged arm restores even spray coverage and helps the arm spin freely so glasses and bowls come out consistently clean.

• Directs high-pressure jets to the upper rack and rotates under water pressure for full coverage
• Maintains even water distribution to improve cleaning performance
• Common symptoms of a failed arm: top-rack items not getting clean, arm not spinning, uneven spray, cracks or clogged nozzles

• Disconnect power and water supply before servicing the dishwasher
• Remove or lower the upper rack if needed; release the retaining nut/clip and pull the old arm straight off
• Seat the new arm fully on the hub/manifold and secure the retainer; verify it spins freely
• Run a short test cycle to ensure proper spray and operation

This is the dishwasher upper spray arm that delivers water across the top rack for effective cleaning. It replaces a worn or damaged spray arm to restore proper water distribution and rinse performance. What it does:

• Spins and sprays water across the top rack to help remove food and detergent residue
• Restores proper spray pattern when the original arm is cracked, clogged, or not turning
• Helps prevent poor cleaning, spots, or missed areas on top-rack dishes
• Works with the dishwasher's water delivery system to maintain rinse and wash coverage

• One upper spray arm

• Turn off power and water to the dishwasher before beginning any service
• Inspect and clear any debris from the spray arm and the mounting area before installation
• Hand-tighten or snap the arm into place per your model's instructions; avoid overtightening

This vent fan motor drives the exhaust blower to move air through the appliance, helping clear steam and heat while protecting internal components. Replace a failed or noisy fan to restore proper ventilation and consistent performance. What it does:

• Spins the blower to pull air through the vent path or recirculation filters
• Helps maintain airflow to prevent overheating of internal parts
• Common symptoms: fan won't run, hums but won't spin, weak airflow, or loud/rattling noise

• Includes 1 vent fan motor

• Disconnect power at the breaker and allow the unit to cool before servicing
• If servicing a microwave, be aware high-voltage components can retain a charge even when unplugged—use proper discharge procedures
• Remove the grille or panels to access the blower; note wire locations and the blower's orientation before removal
• After reassembly, verify unobstructed airflow and correct discharge direction (recirculating or vented)

This adjustable leveling leg threads into the appliance base to set height and stabilize the cabinet. Replacing a worn or missing leg helps stop rocking and vibration and helps maintain proper alignment for reliable operation.

• Provides adjustable support at one corner of the appliance
• Helps level the unit for correct alignment with floor or cabinetry
• Reduces rocking, vibration, and rattling noises
• Replaces stripped, bent, cracked, or missing leg

• Disconnect power and, if applicable, shut off water before servicing
• Carefully support or brace the appliance to access the base safely
• Start the new leg by hand to avoid cross-threading; adjust height gradually
• Use a level to check side-to-side and front-to-back, then recheck after positioning

This stud is a small mounting fastener that provides a secure anchor point for attaching appliance components. Replacing a worn or missing stud restores a tight, aligned fit and helps prevent looseness, rattles, or shifting.

• Provides a fixed, threaded anchor for mounting a handle, bracket, or panel
• Helps keep parts aligned and secure during normal operation
• Common replacement for studs that are stripped, bent, broken, or missing
• Symptoms can include a loose or wobbly component, difficulty tightening, or visible damage/corrosion

• Disconnect power and, if applicable, shut off water or gas before servicing
• Wear cut-resistant gloves and handle panels carefully
• Hand-start threads to avoid cross-threading; tighten snugly without over-torquing
• Reinstall any covers or related hardware in their original positions

Color: White. Includes insulation. Other colors: For almond use WP3384157, for biscuit use WP3384157, for black use WP3379920.

This bi-metal is the thermal actuator that releases the detergent dispenser at the proper point in the wash cycle. Replacing a weak or failed actuator restores reliable detergent cup opening and consistent detergent delivery for better cleaning. What it does:

• Heats and flexes when energized by the control to trip the dispenser latch
• If failed, the detergent cup may not open or may open inconsistently
• Can leave detergent in the cup and lead to poor cleaning results
• Often suspected when the cycle runs but the soap door stays closed

• 1 bi-metal actuator assembly

• Disconnect power at the breaker before servicing
• Remove the inner door panel to access the dispenser area
• Note wiring positions and orientation; transfer connectors securely to the new actuator
• The dispenser latch/linkage moves freely and test door release before reassembly

This factory washer is used in appliance assemblies to distribute load under a fastener and maintain a secure, accurate fit. Replace a missing or damaged washer to restore proper stack-up and reduce vibration, noise, or loosening.

• Distributes load and provides proper spacing in the fastener assembly
• Helps keep bolts, screws, or nuts tight to minimize vibration and rattling
• Direct replacement when the original washer is worn, bent, cracked, or missing
• Typical signs include loose panels/brackets, recurring looseness after tightening, or new vibration after service

• Unplug the appliance; shut off water supply if working near hoses or valves
• Note the original hardware stack-up and reassemble in the same order
• Inspect mating surfaces and companion hardware; replace any damaged parts
• Tighten fasteners snugly per service guidance; avoid overtightening

Includes left and right tracks.

This manifold is the OEM gas valve assembly that routes propane or natural gas from the regulator to the oven and burner valves so the appliance can ignite and heat properly. Designed as a direct-replacement service part. What it does

• Channels gas from the regulator to individual burner/oven valves so each burner can ignite.
• Replaces a worn or damaged manifold that can cause weak or no ignition.
• Addresses symptoms such as burners that won't light, oven failing to heat, or inconsistent flame across burners.
• Works with the appliance's existing regulator and control valves when installed correctly.

• Turn off gas supply and electrical power before attempting removal or service.
• Inspect fittings and gaskets; replace any damaged seals to prevent leaks.
• After installation, perform a gas-leak test and verify proper ignition and flame patterns.

Oven light switch.

This tower protector is a small plastic cover that fits over the dishwasher's spray tower. It helps keep dishes and utensils from obstructing the tower's spray outlets so water can circulate properly for consistent cleaning.

• Shields the spray tower to prevent items from blocking water flow
• Helps maintain proper spray pressure and coverage to upper areas
• Replaces cracked, melted, or missing protectors that can lead to poor cleaning
• Common signs it's needed: protector is broken/loose, deformed, or repeatedly falls off; dishes aren't getting clean due to blocked spray

• Disconnect power and water before service
• Allow the dishwasher interior to cool
• Open the door, remove the lower rack, and snap the protector into place per the tower/rack design
• Verify it seats securely and does not interfere with the spray tower movement

Color: white. Measures about 3 inches wide by 4 inches high by 10 inches deep.

Console assembly replaces the appliance's front control panel, restoring a secure housing for the buttons and user interface so you can operate the machine reliably and protect internal electronics. What it does:

• Houses the user controls, button pads and display and provides the mounting location for the control board.
• Replaces cracked, broken or faded panels that make buttons hard to use.
• Addresses symptoms such as missing, sticky or hard-to-press buttons and visible console damage.
• Protects internal electronics from dust and impact while keeping controls accessible.

• Disconnect power to the appliance before beginning work to avoid electric shock.
• Follow the OEM service manual for disassembly and reassembly steps; console removal typically requires removing trim and fasteners.
• Handle display ribbons, connectors and the control board with care to avoid damage.

Made by Whirlpool. This kit includes 15 feet of copper tubing, saddle valve, teflon tape, and tubing connector. Use this kit to connect your refrigerator ice maker to water supply (usually your water shut off valve under the kitchen sink).