Whirlpool Dishwasher Parts

The Rotating Handle is an OEM part for Whirlpool mixers. It allows you to raise and lower the mixing bowl for convenient access during the mixing process.

A bad rotating handle can be caused by regular use, accidental damage, or excessive force applied during operation. If you notice cracks, a loose or wobbly fit, or difficulty in rotating the handle smoothly, it may indicate a problem with the handle itself.

Symptoms of a bad rotating handle include:

• Cracked or damaged handle surface
• Loose or insecure fit of the handle on the mixer
• Inability to raise or lower the mixing bowl 

Replace your faulty handle with this genuine OEM part to restore your mixer. 

This Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

This is the lid assembly for the dispenser. It covers and protects the dispenser compartment, helping keep debris out and ensuring the dispenser opens and closes properly.

• Covers the dispenser compartment to prevent spills and contamination
• Helps ensure proper dispenser operation
• Common fix when the dispenser lid is cracked, broken, loose, or won't stay closed

• Disconnect power and shut off water before servicing
• Open the dispenser area and remove any retaining screws or tabs
• Transfer any reusable hardware from the old lid to the new assembly
• Test operation before returning the appliance to service

Fits most Kitchen Aid dishwashers. Replaces old 2 coil valves.

This manifold channels wash water within the dishwasher's spray system. Replacing a damaged or clogged manifold helps restore proper water flow and cleaning performance while reducing the chance of leaks at internal connection points.

• Routes high-pressure wash water through the dishwasher's spray system
• Maintains a sealed path to help prevent internal leaks
• Supports consistent spray pressure for effective cleaning coverage
• Helps resolve symptoms such as poor cleaning, weak spray, leaks, or visible cracks in the manifold

• Disconnect power and turn off the water supply before servicing
• Access from inside the tub; remove racks or panels as needed to reach the manifold
• Release retaining clips/screws and note the manifold's orientation; inspect any related seals/O-rings and replace if worn
• Reassemble and run a short cycle to check for proper spray and leaks

This dishwasher drain hose channels wastewater from the pump to your home drain or air gap. Replacing a cracked, kinked, or clogged hose restores proper draining performance and helps prevent leaks or water backing into the tub. What it does:

• Routes wastewater from the dishwasher to the household drain or air gap
• A damaged, kinked, or blocked hose can cause slow/no drain, standing water, or leaks
• Visible splits, soft spots, or persistent odors/backflow are common signs the hose should be replaced
• Restores reliable draining and helps protect surrounding cabinets and flooring from water damage

• 1 drain hose

• Disconnect power and shut off water before servicing
• Pull the dishwasher forward and place a towel or pan to catch residual water
• Match the original routing and maintain a proper high loop or air gap per local code to prevent backflow
• Secure connections with clamps, ensure the hose isn't kinked, and run a test cycle to check for leaks

Color: Black

This rack track assembly guides the dishrack as it slides in and out, keeping it aligned and stable. Replacing a worn or broken track restores smooth rack movement and helps prevent derailing and uneven loading.

• Supports and guides the rack for smooth sliding action
• Maintains rack alignment to prevent wobbling or tipping
• Replaces cracked, warped, or broken rack tracks
• Common symptoms: rack binds, won't extend fully, falls off/derails, or sits unevenly

• Disconnect power to the appliance before servicing
• Pull the rack forward and release any rack end stops per your model
• Remove the old track, position the new track, and fully engage mounting tabs/clips
• Reinstall stops and verify the rack slides smoothly

This replacement cover restores the appliance's exterior protection and appearance by shielding internal components and helping maintain safe operation. Designed to match the original form and mounting points for a direct-fit replacement. What it does:

• Shields internal parts from dust, spills and accidental contact.
• Helps keep wiring and controls securely enclosed to reduce risk of damage.
• Restores a flush, finished exterior when the original cover is cracked, broken or missing.
• Prevents rattling or snagging caused by loose or damaged panels.

• Disconnect power (unplug or shut off breaker) before starting any work.
• Installation typically requires basic hand tools (screwdriver/socket); follow factory service instructions for fastener locations.
• Handle edges carefully—parts may have sharp edges; support the panel during removal/installation to avoid scratches or dropped hardware.
• Reinstall all fasteners snugly but avoid over-torquing; verify panels align and clear moving parts before restoring power.

This tub wheel mount secures the rack support roller to the dishwasher tub wall so racks roll smoothly. Replace a cracked or loose mount to restore smooth rack movement and prevent binding or sagging during loading and unloading.

• Secures the tub roller/wheel to the dishwasher's inner tub wall
• Provides a stable point so the rack glides smoothly on its track
• Helps keep the rack level and properly aligned
• Common symptoms: rack hard to slide, tilts or drops, scraping/grinding when moving the rack

• Disconnect power and water supply before servicing
• Pull the rack forward to access the mount on the tub sidewall
• Remove the retaining fastener or release locking tabs, then install the new mount in the same orientation
• Ensure the wheel engages the track and test rack travel for smooth operation

This motor-pump assembly replaces the washer's combined motor and pump to move water out during drain and spin cycles, restoring proper draining and helping reduce drain-related noise and standing water in the tub. What it does:

• Pumps water out of the tub during drain and spin cycles.
• Drives the impeller that clears water through the drain hose and pump housing.
• Common symptoms: washer won't drain, water remains after cycle, loud humming/grinding or vibrating during drain, or intermittent drain failures.
• Stops or limits water flow caused by pump failure or seized impeller.

• Always disconnect power and turn off water supply before beginning service.
• Follow the appliance's service manual and wiring diagram for safe removal and reconnection of electrical and plumbing connections.
• Inspect hoses, clamps, seals and mounting gaskets when replacing the pump; replace any damaged parts to prevent leaks.

Restore worn dishwasher racks and help prevent rust stains on dishes. This white rack repair kit covers chipped or exposed rack tines and caps bare metal to reduce corrosion and extend the useful life of your racks.

• Re-coats rusted or chipped vinyl on rack tines to help stop corrosion
• Caps exposed tips to reduce rust transfer, scratching, and snags
• Useful when tine caps are missing or the rack coating is flaking
• Common symptoms: rust on tines, stained dishes, sharp/rough tine ends

• Disconnect power and remove the rack before repair
• Clean and dry affected areas thoroughly before applying coating
• Apply in a well-ventilated area; allow full cure time before using the dishwasher
• Replace the rack if metal is severely corroded or broken

This circulation pump and motor assembly moves wash water through your dishwasher's spray arms to clean dishes. Replace a worn or seized wash motor to restore proper spray pressure, quieter operation, and consistent cleaning performance.

• Circulates wash water through the spray arms during wash and rinse cycles
• Restores cleaning performance when the original wash motor won't run or is weak
• Typical symptoms: no/weak spray action, dishes still dirty, loud humming or grinding during wash
• Leaks at the pump housing or shaft area can indicate the assembly has failed

• Disconnect power at the breaker and shut off the water supply before servicing
• Remove the toe panel and slide the dishwasher out to access the underside
• Have a towel or pan ready for residual water; disconnect wiring and hoses, noting their orientation
• Transfer and secure existing clamps/mounting hardware as needed; ensure seals are properly seated and test for leaks after reassembly

The Track Stop is an OEM part for Whirlpool dishwashers. It is a component located on the tracks inside the dishwasher that holds and guides rack movement during operation. 

Symptoms of a bad track stop include:

• Racks or dishes sliding uncontrollably during the cycle  
• Difficulty fully extending or retracting racks
• Noise or grinding sounds noticed from rack movement
• Damage or wear visible on the rack tracks

Causes of a bad track stop can be a failure due to normal wear and tear over repeated use. Opening and closing the dishwasher door thousands of times can degrade track stops.

This OEM Whirlpool replacement track stop ensures proper rack guiding, securing its position to deliver dependable performance cycle after cycle. This OEM replacement is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

The Upper Rack Tub Mount Roller is an OEM part compatible with Whirlpool dishwashers. It is located in the upper rack and plays an important role in providing a smooth movement of dishes across the rack. The roller enables seamless movement of dishes in and out during loading and unloading. 

Causes of a bad roller can include wear and tear from repeated use, damage from overloading or unbalanced loads, or debris buildup that prevents proper rolling.  

Symptoms of a bad Upper Rack Tub Mount Roller include:

• Dishes getting stuck or stuck in the upper rack
• Difficulty sliding dishes in and out of the upper rack  
• Noisy or grinding sounds coming from the upper rack area
• Upper rack that does not move smoothly

 This OEM replacement is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

Color: White. Includes insulation. Other colors: For almond use WP3384157, for biscuit use WP3384157, for black use WP3379920.

This vinyl door seal lines the perimeter of the appliance door to help block air and moisture leaks, cushion the close, and maintain proper operation. Replace a worn seal to restore a tight, quiet, reliable door closure.

• Creates a continuous seal around the door opening to reduce leaks
• Helps contain air and moisture and dampens door vibration
• Replace if the seal is torn, cracked, flattened, or coming loose
• Symptoms include gaps or drafts at the door, noise, or visible wear

• Disconnect power; for gas appliances, also shut off the gas supply
• Remove inner door panel/trim as needed to access the seal area
• Remove the old seal and clean the mounting surface of residue
• Install the new seal without stretching; if your model uses adhesive, apply per instructions and allow proper cure time