Whirlpool Gasket & Seal

This heat-resistant fiberglass oven door gasket seals the oven cavity perimeter, helping keep heat inside for consistent temperatures and efficient cooking. Replace a worn, frayed, or flattened seal to restore proper door sealing performance. What it does

• Forms a heat-resistant seal around the oven opening to minimize heat loss
• Helps maintain set temperature and overall cooking performance
• Can help address long preheat times, uneven baking, and hot air leaking around the door
• Replace if the gasket is frayed, brittle, compressed, or falling out of its channel

• Includes: 1 fiberglass door gasket

• Disconnect power and allow the oven to cool completely before service
• Remove the old gasket from its mounting slots or clips; clean the channel of debris
• Install the new gasket without stretching; seat it evenly around the perimeter with ends routed as originally positioned
• Close the door and check for uniform contact all around; adjust seating if needed

This freezer door gasket seals the door to the cabinet to keep cold air in and humid air out. Replacing a worn gasket restores a proper seal, helping maintain temperature and reducing frost and condensation around the door.

• Creates a continuous perimeter seal between the freezer door and cabinet
• Helps stabilize freezer temperatures and limits warm-air leaks that can lead to frost/ice buildup
• Common failure signs: torn or hardened gasket, visible gaps, moisture or ice near the door
• Almond color to match compatible units

• Disconnect power to the refrigerator before servicing
• Warm the new gasket in hot water or with low heat to relax folds, then start at the corners and work evenly around the door
• On screw-retained styles, loosen perimeter screws and tuck the gasket lip under the retainer; tighten evenly
• After installation, check seal with a dollar-bill test and allow up to 24 hours for the gasket to fully conform

This seal restores a tight barrier between two mating parts in your appliance to prevent leaks and contamination. Replacing a worn or cracked seal helps stop drips, drafts, and noise so the unit can run reliably.

• Forms a tight seal between components to contain fluids or air
• Helps prevent leaks, drips, condensation, or unwanted airflow at joints
• Maintains efficient performance and reduces noise or vibration from loose fits
• Common failure signs: visible cracks/flattening, moisture where parts meet, odors, or louder operation

• Disconnect power and shut off water before servicing
• Note the seal's orientation; remove the old seal and clean all mating surfaces
• Install without stretching; lightly moisten if specified by your service manual (avoid petroleum products unless directed)
• Reassemble and test for proper operation and any leaks

Color: Grey

This oven door gasket creates a tight, heat-resistant seal between the door and the oven frame. It keeps hot air inside, helps the oven reach and hold temperature, and protects nearby surfaces from escaping heat. What it does

• Seals the gap around the oven door to reduce heat loss
• Supports accurate temperatures and more even baking performance
• Replaces gaskets that are brittle, flattened, torn, or frayed
• Common symptoms: heat felt escaping around the door, longer preheat/cook times, temperature swings, visible damage to the gasket

• One door gasket

• Disconnect power at the breaker and allow the oven to cool completely
• Open the door and pull the old gasket straight out of its retaining holes/clips
• Start at the top center; press the new gasket's tabs into place without stretching, ensuring corners are fully seated
• Close the door to confirm uniform contact all the way around the seal

This oven door gasket restores a tight seal between the door and the oven front frame. A proper seal reduces heat loss, supports accurate temperatures, and helps food bake and roast more evenly.

• Creates a heat-resistant seal at the door-to-cavity opening to contain heat and airflow
• Helps maintain stable oven temperatures and normal preheat times
• Replace if the seal is torn, frayed, brittle, flattened, burned, or leaking
• Helps resolve heat escaping around the door, uneven baking, or longer cook times

• Disconnect power; for gas appliances, also shut off gas. Allow the oven to cool completely
• Remove the old gasket by releasing end retainers or pulling it from the channel; clean the groove
• Install the new gasket without stretching; seat it evenly around the perimeter with corners aligned
• Close the door and check for uniform contact all around; adjust as needed per your model instructions

This adhesive-backed foam tape seals small gaps and cushions mating parts inside your appliance. Replacing worn or missing foam helps reduce noise and vibration while preventing air leaks and condensation that can lead to performance issues.

• Seals joints and gaps to help maintain proper airflow and temperature control
• Cushions panels and components to reduce rattles, buzzing, and vibration
• Helps prevent moisture intrusion that can cause condensation or frost
• Restores secure fit where original foam has compressed, torn, or fallen off

• Disconnect power (and water supply if applicable) before starting
• Remove all old foam/adhesive and clean surfaces; allow to dry fully
• Measure, cut to length, peel backing, and apply without stretching the tape
• Press firmly along the length for good adhesion; keep clear of moving parts and vents

This replacement seal restores a tight barrier between mating parts inside your appliance to prevent leaks and keep the assembly performing as designed. Swapping a worn or brittle seal helps stop drips and protects nearby components. What it does:

• Creates a reliable seal between components or around a shaft to prevent leakage
• Helps maintain proper pressure/flow within the system
• Typical failure signs: cracks, flattening, swelling, brittleness, or leakage/residue at the joint

• 1 seal

• Disconnect power; shut off water supply if applicable
• Allow hot components to cool before servicing
• Access the sealed joint; capture any residual water if working on a wet system
• Clean mating surfaces; seat the new seal evenly. Use only manufacturer-approved lubricant if specified, then reassemble and test for leaks.

This inlet/outlet seal creates a watertight barrier where two water passages meet in your appliance. Replacing a worn seal helps stop leaks at the connection and maintains proper water flow and performance.

• Forms a tight seal at an inlet/outlet connection to prevent water leaks
• Helps maintain correct water flow and pressure through the system
• Common signs of failure: drips or pooling water near the unit, visible cracks, flattening, or deformation of the seal
• Can resolve recurring leaks after reassembly of water-line connections

• Disconnect power and shut off the water supply before servicing
• Access the connection point and note the seal's orientation
• Clean mating surfaces; seat the new seal evenly without twisting
• Reassemble, restore water/power, and check carefully for leaks during a test run

Color: clear. It measures about 3-1/2 inches in diameter.

This door gasket is the replacement seal that fits around an oven door to help contain heat and maintain cooking temperature. Replacing a worn gasket improves oven efficiency and reduces heat loss for more consistent results. What it does

• Seals the oven door to retain heat and maintain set temperatures.
• Helps prevent heat and smoke from escaping during use.
• Can reduce uneven cooking and long cook times caused by leaks.
• Helps limit high exterior temperatures around the door area.

What's included One door gasket. Install notes

• Disconnect power and allow the appliance to cool completely before starting work.
• Seat the gasket evenly into the door channel or retainer per OEM instructions; do not force or overstretch.
• Do not use adhesives unless the manufacturer specifies them; check door alignment and the seal after installation.

Size: 1-1/16 x 5/8 inch. Used for fill hose. For a 4 pack order 285448A

This washer bellow, also called the door boot seal, forms the watertight gasket between the front door opening and the outer tub. Replacing a worn or torn bellow helps stop front leaks and keeps wash water inside the machine.

• Creates a watertight seal between the door opening and outer tub on front-load washers
• Helps prevent water on the floor from leaks at the door area
• Common failure signs: water leaking from the front/door, visible tears or cracks, persistent mildew/odor on the gasket, or the seal pulling loose

• Disconnect power and turn off water supply before service
• Remove the outer retaining clamp, then access and remove the inner clamp as required by your model
• Note orientation marks/drain openings on the bellow and seat it evenly on both the tub and front panel
• Reinstall clamps securely and run a brief test fill to check for leaks

This felt door vent seal fits around the dishwasher's door vent to help contain steam and moisture within the inner door. Replacing a worn seal helps prevent minor leaks and condensation around the vent area during cycles.

• Creates a gasket between the vent assembly and inner door panel to keep steam directed through the intended vent path
• Reduces moisture escape that can cause drips or water spots on the outer door or nearby countertop
• Helps limit condensation or musty odors from trapped moisture inside the door panel
• Indicators of failure include visible wear or separation of the felt and moisture around the vent during operation

• Disconnect power and turn off water supply before servicing the dishwasher
• Remove the inner door panel to access the vent assembly
• Note the seal's orientation; clean mating surfaces; seat the new felt evenly around the vent with no gaps
• Reassemble and run a short test cycle to check for leaks at the vent area

Located between the console and door

Fiberglass-reinforced door seal that restores an appliance door's airtight closure to help maintain consistent temperatures, reduce energy waste and minimize frost or moisture buildup around the door. What it does:

• Forms a continuous gasket around the door to keep cold air in and warm air out.
• Helps prevent frost buildup and uneven temperatures caused by air leaks.
• Common symptoms that indicate replacement: visible gaps, cold-air leakage, frost/ice at the door, or a door that won't seal flush.
• Fiberglass construction helps the seal retain shape for a more reliable long-term closure.

• Disconnect power to the appliance before beginning any service.
• Remove the old seal and clean the door channel; press the new seal evenly into place, checking for full contact around the perimeter.
• Some models may require partial door or liner removal—before disassembly.
• If the seal is stiff, follow OEM-recommended conditioning (allow to warm to room temperature or use manufacturer guidance) to help it seat properly.