Whirlpool Gasket & Seal

This replacement seal keeps liquids and food particles out of the blender motor housing to protect internal components and help prevent leaks. Fits the motor assembly where the shaft passes through the housing. What it does

• Seals the motor shaft opening to help prevent liquid from entering the motor housing.
• Reduces risk of motor damage or shorting caused by leaks into the base.
• Helps stop leaking at the blender base or around the blade assembly when worn.
• Replace if the seal is cracked, flattened, swollen, or shows visible wear.

• Always unplug the appliance before disassembly and removal of the jar or motor housing.
• Remove the blade and jar assembly per the service diagram to access the shaft seal; inspect mating surfaces and replace damaged components.
• Ensure the new seal is seated evenly around the shaft and in its groove; do not force or over-stretch the seal.
• After reassembly, run a short water test (with the unit unplugged from any direct water source) to check for leaks before normal use.

Service tub gasket that creates a watertight seal between the washer tub and cabinet. Replaces a worn or damaged seal to help stop leaks and limit water damage around the appliance. What it does:

• Seals the tub opening to prevent water from leaking onto the floor during fill, wash and drain cycles.
• Restores the seal that keeps moisture confined to the tub and reduces mildew buildup at the tub edge.
• Helps eliminate spray and dripping that can occur with cracked, torn or hardened gaskets.
• Supports normal drum/tub operation by maintaining the intended tub-to-cabinet seal.

• Disconnect power and shut off water supply before starting any repair.
• Inspect and clean mating surfaces before installing the new gasket; ensure proper orientation and seating into the groove or mounting channel.
• Use original clamps or fasteners and tighten evenly; replace any missing or damaged mounting hardware before testing for leaks.

This replacement refrigerator door gasket restores a tight seal between the door and cabinet to help maintain proper temperature and reduce frost and moisture. Use it when the existing seal is torn, warped, or not sealing evenly.

• Creates an airtight barrier around the door to limit warm air infiltration and cold air loss
• Helps minimize frost/ice buildup and condensation at the door opening
• Replaces cracked, shrunken, or deformed gaskets that leave gaps or air leaks
• Common symptoms include visible tears, moisture on or around the seal, temperature fluctuations, or a door that won't seal fully

• Unplug the refrigerator; allow the new gasket to warm to room temperature. Gentle warming (hot water bath or low heat) can help relax kinks.
• Clean the door's sealing surface. Remove the old gasket carefully to avoid damaging any retaining channel.
• Fit corners first, then work along the sides for an even, uniform seal. Design and attachment method vary by model.
• Close the door and check for even contact (dollar-bill test). Readjust gasket seating or door alignment as needed.

This freezer door gasket creates a tight seal around the door to keep cold air in and humid air out. Replacing a worn gasket restores proper temperature control, reduces frost, and helps the door close and seal correctly.

• Seals the gap between the freezer door and cabinet to maintain cold temperatures
• Blocks warm, moist room air that can cause frost and ice buildup
• Helps prevent sweating/condensation around the door perimeter
• Addresses issues from torn, shrunken, brittle, or deformed gaskets that won't seal

• Disconnect power before servicing; clear items from the door
• Lay gasket flat and warm gently (hot water or low heat) to relax kinks before installation
• Loosen inner-liner screws/retainer, press gasket fully into the channel, then tighten screws evenly
• Perform a dollar-bill test around the perimeter; gently warm stiff areas to smooth and adjust door alignment if needed

This refrigerator door gasket for foam-in-place doors creates a tight seal around the door opening to keep cold air in and moisture out, helping maintain stable temperatures and reduce frost and energy waste.

• Seals the door perimeter to prevent warm air leaks
• Helps maintain correct cooling performance and humidity levels
• Reduces frost and condensation caused by poor sealing
• Common signs it's needed: tears, warping, gaps, persistent frost/condensation, door not sealing or popping open

• Disconnect power before servicing
• Warm and relax the gasket in hot water or with a hair dryer on low to ease installation
• Remove the old gasket from the retainer/channel; install the new gasket starting at the corners and press fully into place
• Check the seal all around and adjust the door/hinges as needed; allow time for the gasket to set

Replace a worn or leaky seal with this refrigerator door gasket. It creates an airtight barrier between the door and cabinet to keep cold air in, reduce frost and moisture, and help your refrigerator run efficiently.

• Forms the perimeter seal so the door closes tightly against the cabinet
• Helps maintain stable temperatures and humidity, reduces frost/condensation, and limits energy loss
• Replace if the gasket is torn, cracked, deformed, or not sealing evenly
• Common symptoms: warm spots, moisture around the door, frost along the liner, or the door popping open

• Disconnect power before servicing
• Warm the new gasket in hot water or with low heat to relax shipping folds for easier fit
• If your model uses a retainer, loosen screws, remove the old gasket, press the new lip fully into the channel, then tighten evenly
• Check the seal all around and adjust hinges if needed; use a "dollar-bill test" to ensure even tension

This mounting gasket creates a tight, cushioned seal where a component attaches to its housing or bracket. Replacing a worn seal helps stop leaks and rattles while restoring a secure, reliable connection at the mounting point.

• Forms a seal between two mounting surfaces to help prevent leaks or seepage
• Cushions and isolates vibration for quieter operation
• Helps maintain proper alignment of the mounted component
• Replace if the gasket is cracked, flattened, brittle, or no longer sealing

• Disconnect power and shut off water or gas, if applicable
• Note the gasket's orientation before removal
• Clean and dry both mating surfaces; remove all old gasket material and residue
• Seat the new gasket evenly; reassemble and tighten fasteners snugly without overcompressing; test for leaks/operation

This vinyl door seal lines the perimeter of the appliance door to help block air and moisture leaks, cushion the close, and maintain proper operation. Replace a worn seal to restore a tight, quiet, reliable door closure.

• Creates a continuous seal around the door opening to reduce leaks
• Helps contain air and moisture and dampens door vibration
• Replace if the seal is torn, cracked, flattened, or coming loose
• Symptoms include gaps or drafts at the door, noise, or visible wear

• Disconnect power; for gas appliances, also shut off the gas supply
• Remove inner door panel/trim as needed to access the seal area
• Remove the old seal and clean the mounting surface of residue
• Install the new seal without stretching; if your model uses adhesive, apply per instructions and allow proper cure time

This oven door gasket fits select 30-inch models and restores a tight, heat-resistant seal between the door and oven cavity. Replacing a worn gasket helps contain heat, support accurate temperatures, and protect surrounding surfaces from excess heat.

• Maintains a thermal barrier to keep hot air inside the oven cavity
• Helps the oven reach and hold the set temperature
• Reduces heat escaping around the door for more consistent baking
• Replaces gaskets that are cracked, frayed, flattened, or leaking; common symptoms include long preheat times, temperature swings, or feeling heat escaping at the door edge

• Disconnect power at the breaker and allow the oven to cool completely
• Remove the old gasket from the frame, noting the orientation of any end clips or pins
• Clean the frame/channel to remove debris for a proper seal
• Install the new gasket without stretching; seat clips/pins fully and check for even contact all around

This oven door gasket restores a tight seal between the door and oven cavity so your appliance can hold set temperatures. Replacing a worn seal helps reduce heat loss for more consistent preheating and baking results.

• Seals the gap between the oven door and frame to keep heat and moisture inside
• Helps maintain accurate oven temperatures and reduce energy loss
• Replace if the gasket is torn, hardened, flattened, frayed, or falling out of its channel
• Common symptoms: heat escaping around the door, long preheat, uneven baking, odors or smoke leaking from the oven

• Disconnect power and allow the oven to cool completely before servicing
• Gently pull the old gasket from the channel or unhook its retainers; note clip locations/orientation
• Press the new gasket evenly into the groove without stretching; align any corner pins/clips to match the original
• Close the door and check for uniform contact around the seal

This factory washer is used in appliance assemblies to distribute load under a fastener and maintain a secure, accurate fit. Replace a missing or damaged washer to restore proper stack-up and reduce vibration, noise, or loosening.

• Distributes load and provides proper spacing in the fastener assembly
• Helps keep bolts, screws, or nuts tight to minimize vibration and rattling
• Direct replacement when the original washer is worn, bent, cracked, or missing
• Typical signs include loose panels/brackets, recurring looseness after tightening, or new vibration after service

• Unplug the appliance; shut off water supply if working near hoses or valves
• Note the original hardware stack-up and reassemble in the same order
• Inspect mating surfaces and companion hardware; replace any damaged parts
• Tighten fasteners snugly per service guidance; avoid overtightening

This replacement seal restores a tight barrier between mating parts in your appliance, helping maintain proper performance. It replaces a worn or deformed factory seal that can no longer hold a reliable fit due to age, heat, or chemical exposure.

• Creates a tight barrier between components to prevent leaks or air intrusion, as designed for the assembly
• Helps maintain correct pressure/flow and overall performance
• Common signs of failure: cracks, flattening, brittleness, or residue at the joint
• Helps address moisture seepage or performance loss at the sealed connection

• Disconnect power and, if applicable, turn off water supply before servicing
• Access the sealed joint; note the original seal's orientation
• Clean and dry mating surfaces thoroughly; install the new seal evenly and squarely
• Do not use sealants or lubricants unless specified by the manufacturer; test for leaks/fit before reassembly

FIP door gasket in black. This perimeter seal installs on a refrigerator or freezer door to keep cold air in and humid room air out, restoring proper closure and helping cut down on frost, condensation, and temperature swings.

• Creates a tight seal between the door and cabinet to maintain interior temperatures
• Helps reduce frost/ice buildup and moisture around the door opening
• Supports efficient operation by limiting warm air infiltration
• Common failure symptoms: tears or cracks, warped corners or gaps, brittle rubber, door not closing or staying shut, condensation around the gasket

• Unplug the appliance and clear items from the door being serviced
• Warm the new gasket in hot tap water or with a hair dryer on low to relax packaging bends; do not overheat
• Start the corners, then press the gasket fully into the channel/under retainers along each side
• Allow the gasket to settle/form over the next day

Oven door gasket forms the heat seal around the oven door opening to keep heat inside for even cooking and efficient operation. Replaces worn or torn seals to reduce heat loss and improve bake performance. What it does:

• Seals the oven cavity to maintain proper cooking temperature and improve efficiency.
• Helps prevent heat and smoke from escaping around the door.
• Commonly used to address long bake times, uneven cooking, or visible gaps/damage at the door edge.
• Flexible design fits into the door channel to restore a snug seal.

• Disconnect power (and gas supply, for gas ovens) and allow the appliance to fully cool before starting.
• Inspect the door channel and remove old gasket; some models require partial door removal.
• Press the new gasket into the channel evenly; ensure any retaining clips or tabs are fully seated.
• Wear gloves to protect hands from sharp edges and avoid using sharp tools that could damage the new gasket.

Replacement gasket that restores a tight seal to the appliance door and helps prevent water or air leaks. Replaces worn, cracked, or compressed seals so the door closes properly and reduces moisture or heat loss. What it does:

• Seals the door opening to stop leaks of water, steam, or heated air.
• Helps maintain proper temperature and efficiency by preventing air exchange.
• Reduces condensation, odors, and cycling caused by a poor seal.
• Common signs you need this part: visible gaps or damage, leaks around the door, excess moisture, or poor heating/cooling performance.

• Disconnect power and water (if applicable) and allow the appliance to cool before starting.
• Clean and dry the mating surface to ensure a proper fit; remove old adhesive or debris.
• Align the gasket into the door channel or groove and press evenly; avoid stretching the material.
• If the door or mounting hardware is bent or damaged, repair those parts before installing the gasket.