Need Help?
Call or text
Oven not heating or preheating slowly? This lower bake element restores even baking when burned out or damaged. DIY-friendly, 5-minute install.
Turned off 40 Amp breaker. Removed shelves from oven. Removed two screws in back panel holding element in place. Slowly pulled element free making sure wires stayed attached and not lost in oven insulation. Removed two wires from old element. Attached wires to new element. Pushed wires back into oven rear wall. Reinstalled the previously removed two screws. Turned on breaker. Total time less than 10 minutes. Read more
Oven not heating or baking unevenly? This lower bake element restores consistent bottom heat. Simple DIY repair—clips in and tightens in 5-10 minutes.
Replaced bake element. Read more
Burner not heating? This radiant surface element restores heat output beneath your glass cooktop. Straightforward repair with basic tools.
Need to open because no parts’ numbers can be identified through their website. But the rest “order and put in” are very easy steps. Will come back if I do need other parts Read more
This 8-inch surface coil element restores a burned-out or damaged heating element on an electric cooktop. It delivers consistent 2100W heat for everyday boiling, frying, and simmering, so your range burners perform like new.
We had ordered and installed the drip pans and when we took a look, we knew we needed new elements. Those were perfect; exact replacement. The problem was on the eight inch units, the rim of the drip pan touched the element. It was a simple matter of removing a small bit of the drip pan where the element enters. Aircraft snips and a little polishing with a Dremel tool, and all is well. Wife loves the new elements. Read more
Oven not heating evenly or convection mode not working? This rear convection element restores even baking and roasting. 20-minute DIY repair.
Whirlpool convection oven. Access to convection element from inside. Three screws to remove plate covering fan blade. Then one screw to remove element bracket. I placed tape over the holes with the wires so they wouldn’t pull back into the panel. Remove old element at tabs and replace. Very easy fix. Removing door to oven made it easier to get to but not necessary. Read more
Oven not heating or baking unevenly? The bake element provides bottom heat for baking and roasting. Easy DIY repair when coils deteriorate from heat cycling.
A replacement baking element - easy to replace. Read more
This part is a grill element that is used on a cooktop. The element is responsible for supplying heat to the cooking area of the cooktop. If the element is not lighting up orange or red when it is turned on, it will need to be replaced. This part may need to be replaced over time due to normal wear and tear on the appliance. Some users may also notice that the element is not heating evenly or works intermittently. If this is the case, this is a genuine OEM replacement part that is made out of high-quality materials. Unplug the range from the electrical outlet and allow the cooktop ample time to cool down before trying to replace it. Wear work gloves for safety during this process.This part is compatible with cooktops that are manufactured by Jenn-Air and Maytag. It is sold individually and comes from the manufacturer.
Ordered all the parts needed, replaced them and the Jenn Air worked just fine. Read more
Dryer not heating or taking too long to dry? This heating element generates heat to dry clothes. DIY repair typically takes 30-60 minutes with basic tools.
Used multimeter to diagnose no continuity through heating element. Took out element and found underwire from a bra (C-cup I think...) had shorted it and caused a break. Replaced heating element and ... still no heat. Found that one of the fuses had no continuity also. Replaced the fuse and everything working fine. Read more
This 8-inch surface element restores reliable heating on an electric range or cooktop. Replace a failed burner to bring the cooking zone back to proper operation and consistent cooking performance. What it does:
We ordered the part it arrived within a couple of days and my son installed it without any trouble. Read more
This radiant surface heating element restores proper burner performance on electric glass cooktops/ranges. It replaces a failed element so cookware heats evenly and reliably beneath the ceramic glass. What it does:
Parts came in and they were exact replacements so no problem changing them out. The stove works great. Read more
Burner won't heat or has cold spots? This surface heating element restores reliable, controllable heat to your cooktop. Direct-fit replacement.
The replacement element included extensions to make the wires long enough. Read more
Dryer not heating? This heating element restores warmth to both high and low heat cycles. DIY-friendly repair takes about 30 minutes with basic tools.
After watching several u tube videos I borrowed a friends multi meter and tested element , high level thermostat and the thermistor. Ordered parts from applianceparts pro , at a significant lower price than the local parts warehouses around my area!! Dryer is working great! Read more
Broil element not heating or sparking? This top heating element restores radiant heat for broiling and browning. DIY repair takes 15-30 minutes.
I am extremely happy to say that I ordered my replacement part from Appliance parts Pros.com. This is the 3rd time I have done business with them and like each time before I looked at a video they have showing how the repair is to be properly done. Best website hands down for appliance parts! Read more
Fix a broiler that won't heat or a melted element. This range broil element delivers direct radiant heat at the top of your oven during the broil cycle.
Replaced the element. Read more
Washer water heater element raises water temperature during wash cycles. Replace if cracked, corroded, or no longer heating properly in your machine.
Burner not heating or heating unevenly? This 8-inch surface element restores reliable cooktop performance. Simple plug-in installation in minutes.
REPLACED NEW RIGHT FRONT POWER BURNER. THIS DID NOT FIX THE PROBLEM. I THEN REPLACED THE BURNER CONNECTING SWITCH BY FOLLOWING THE INSTRUCTIONS ON YOUR VIDEO. BURNER HEATS UP NORMALLY, BUT I DON'T KNOW YET IF IT WILL SUDDENLY GO TO THE HIGH SETTING. IT WAS A SPORADIC PROBLEM I WAS HAVING...SO I'M HOPING THIS SOLVES THE ISSUE. FINGERS ARE CROSSED....BUT IN EITHER CASE....I NEEDED A NEW BURNER. REPAIR WAS SIMPLE....THE INSTRUCTIONAL VIDEO WAS VERY EASY TO FOLLOW. Read more