Need Help?
Call
Washer only fills with hot water or stops mid-cycle? The water temperature switch controls incoming water temps for proper cycle selection. DIY repair.
I tested the Atc. mid level switch, with my multi tester and found it was not sending enough current to the cold water inlet valve, so it would not open and let cold water in. I replaced the switch, (it was a snap) literally it snapped in place. replace the front face and turned the water back on and plugged in the washer, and turned it on. It worked perfect and has been since. good and easy repair even for a novice like me.. Read more
Washer won't spin or stops mid-cycle? A faulty lid switch prevents operation when the lid is bumped or opened. Simple snap-in replacement restores cycles.
I had removed three screws behind the control board cover of the washer, to access the old lid switch. I checked the continuety of the of the switch with a multimeter and it obviously failed the the test by displaying infinity of <1, rather than being 0. I removed the old switch with a flathead screw driver, I tested the new one and installed it in no time. Problem solved!!! Read more
Washer won't start or fill with water? A faulty lid switch assembly with fuse is often the cause. DIY-friendly repair—most complete it in under an hour.
Removed front and top panels of washer, removed old switch assembly. Then mounted and hooked up new switch assembly, put panels back on, turned on power and unit now works fine. Thanks for the quick delivery on the part...our total machine down time was only 36 hours. Biggest difficulty was getting the machine out of its position to work on it! Read more
Washer won't spin or door won't lock? This door lock spin enable switch signals the control to start high-speed spin. Moderate DIY repair, 30-60 minutes.
Replaced the motor wax door lock switch and the door lock spin enable switch. Read more
Fix a burner stuck on high or won't adjust temperature with this infinite switch. Controls cooktop burner heat levels. DIY repair in under 30 minutes.
Replaced the Infinite Switch and that solved the problem. Did not need to replace the Surface Element Read more
This is the washer's water level switch that senses tub level via air pressure and provides five selectable fill settings. Replacing a failed switch restores accurate filling and lets the cycle advance properly through wash, rinse, and spin.
Replaced the water level switch and water level pressure switch hose. Video on AppliancePartsPros.com detailed the procedure. Read more
This limit switch monitors a set condition and opens or closes its contacts when that limit is reached. Replacing a failed switch restores proper safety cutoff and consistent operation of the appliance's heating or movement system. What it does:
I replaced the switch which was bad and also replaced the water inlet valve. Read more
Fix erratic or unresponsive cycle selections with this laundry center rotary encoder switch. Mounts behind the cycle knob to restore accurate settings.
Replaced with a new one. Read more
Fix washer overflowing or not stopping fill cycle. This water level pressure switch senses tub water and signals control to stop filling. DIY repair.
Filled tub to about 6 inches and inspected washer. Noticed that the tube leading from the air entrapment bubble on the exterior side of the drum had a small leak in it. Clipped off the part of the tube that had the hole in it(it was very close to the connector nipple) reconnected and problem was solved. Read more
Dishwasher won't start or stops mid-cycle? A faulty door switch prevents operation when it can't detect the closed door. Simple DIY repair.
This adjustable buzzer kit replaces a failed or noisy mini buzzer to restore audible alerts for cycles, timers and notifications. Compact design lets the appliance signal you reliably when cycles finish or need attention. What it does:
I was looking for a parts sight and found yours. I started to watch all the video tutorials on each part and the "check these connections first video". Well by doing this I was able to find the source of my problem. What I thought was the heating coil not working right, ended up being the timer that was bad!!! I am so very happy with your sight and the step by step videos that were the success to being able to do this on my own. Read more
Fix unresponsive or erratic cycle selection with this rotary encoder switch. Mounts behind the control knob to restore accurate cycle settings and indicators.
Color: White
This rotary on/off switch controls the dryer's Finish Guard (also called Wrinkle Guard/Wrinkle Shield) feature. Replacing it restores proper control of the post-cycle intermittent tumbling that helps reduce wrinkles, preventing the feature from being stuck on or off.
Burner won't adjust heat or jumps to full power? This infinite switch restores variable temperature control to surface burners. DIY install in 30 minutes.
Being cautious, I ordered new burner controls (infinity switches) for the front two burners. I installed them and was very happy with the results. The new controls allowed me to increase or decrease the amount of heat without what you might call thermal runaway (A sudden switch to full-on). Encouraged, I ordered two more burner controls and installed them for the back two burners. I have not yet tested them extensively, but I am confident that I now have four functioning burners. Read more
If your cooktop burner won't heat, stays on one setting, or heats erratically, this control switch regulates power to restore proper temperature selection.
Replaced switch on the gas valve. Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.