Amana Washer Parts

I had replaced the Agitator cams a couple of times already due to my brother-in-law overloading the machine which stripped the teeth off of the cams. I also noticed the agitator seemed to 'wobble' and made 'knocking' noises quite a bit. I reviewed the video on the Appliance Parts Pros web site, disassembled the agitator and cleaned everything up, which helped a little, but not enough. Figuring the agitator itself was worn out also, I looked up and ordered all the parts for the upper agitator on... Read more

Originally the dryer was squeaking a lot, so I purchased a new belt tensioner, but the original tensioner was an old-style no wheel tensioner, so that wasn't the source of the squeaking. I saw a lot of lint had built up inside the unit where there shouldn't have been that much. So I viewed a few videos on the Appliance Pros site and saw that the rear wheel guides were the cause of the squeaking and the rear felt drum and blower housing seal needed to be replaced. The rear blower housing was... Read more

I replaced the washer plate and new screw/washer part. Easy fix and back up and running in ubder 10 minutes. Read more

The part is so new no video so I went onto a similar part and watched video that got me about 80%. Then, called and customer service sent me a service Manual but this still was not specific so I broke the old to get it out and in the process figured out how to do it correctly. So I installed the last bit of it which was the bezel through the machine top by myself correctly. So you take the old one out by pushing out to the right from the bottom side using a screw driver for leverage. It will... Read more

Disassembled washer and replaced gearcase and reassembled. Read more

I contacted AppliancePartsPros and gave them my symptoms and failure codes and they were able to diagnose the problem and send the correct parts to resolve the issue. This is the 3rd or 4th time I've used their service since 2012 and they have been correct on each and every repair issue I've had. Many thanks for the professional advice and help! Read more

• Burning smell

All's well that ends well, but the getting there was a bit of a pain. The web site suggests 3 possible causes for my problem (incl. the burning smell). I began with the first two since they were inexpensive compared to the motor, which was the third cause (and also the least often cause). There is no way to visibly tell if the motor is bad or not. After replacing the clutch assembly, which did have some plastic pins broken off) and the motor coupling (which actually looked fine, but the... Read more

• Shakes and moves
• Noisy
• Pumps but will not spin

18 year old Maytag Atlantis top load washer had a load knocking and rattle sound with excessive vibration when the tub was spinning, but not when it was agitating. They was no water leaking. I took the front panel off and carefully listened while I ran a cycle and the loud sound sounded like it was coming from the drain pump. So I took off the drive belt and noticed that it was glazed and that there was belt material on the drain pump and tub transmission pulleys. I removed the drain pump and... Read more

Replaced the bellow. Read more

Replaced suspension rods. Read more

I had to replace the drive shaft and the lower agitator. The motor coupling was also worn out. The repair was challenging because I had to rebuild the gear box. This step was really messy and I had to wait for the liquid gasket to set prior to completing the repair. Cleaning and prep of all of the parts tripled the repair time. Read more

Pulled the washer apart (using your videos as a refresher) and found that the plastic coupling between the motor and the transmission had failed. Searched for parts vendors and found your site. Ordered the coupling on-line and went back down to clean up the machine. In the cleaning process I found a damaged thrust washer for the upper agitator and broken drive dogs for that same agitator. I went to the website to see if I could augment my initial order. I did not want to pay shipping costs... Read more

It was a fast fix. its a Maytag Centennial Top load washer. it took me about 20mins to remove the pump and instal the new one.Most of the time was spent moving the washer. Read more

First went through the troubleshooting guide on the website and read the various stories and watched the repair videos for replacing the springs and suspension pads. Then before ordering any parts disassembled the machine only to the point of removing the cabinet to see if there were any obvious issues. The springs appeared OK but I couldn't tell of they were fatigued or not and all were in place but the tub suspension pads were definitely worn out. I then put the machine back together and went... Read more

• Will not drain

It was a relatively easy fix. Removed the small access panel at the back of the washing machine after unplugging the unit. The pump is right there. Disconnected the two hoses to the pump, catching some water with towels. Removed three retaining screws, then realized I had not disconnected the belt from under the unit. Easy fix, tilted the unit and disconnected the belt. Put in the new pump , connected the hoses, then reconnected the belts. Works like new! Read more

Ordered the valve body from Appliance Parts Pro. It was very easy to find the part on their website. Ordering was simple. The part actually got here the next day. I received an email about 2 hours after I received the part that contained the tracking number. That is what is known as quick and reliable service. Part was a little hard to replace since I have big hands. There are 2 metal screws that hold the valve body to the washer that are in a small confined area. Unless you want to dismantle... Read more