Bosch Parts

This turbidity sensor detects how clear the dishwasher's wash water is so the control can adjust cycle time, rinses, and water changes. Replacing a faulty sensor helps restore proper cleaning performance and normal cycle lengths.

• Monitors soil level/clarity of the wash water
• Signals the control to extend or shorten wash and rinse phases as needed
• Helps optimize water use while maintaining cleaning results
• Failure symptoms can include unusually long or short cycles, poor cleaning, repeated draining/refilling, or cycles that won't advance

• Disconnect power and turn off the water supply before servicing
• Pull the dishwasher out as needed; access the sensor from the base area
• Place a towel to catch residual water; release the locking tab or twist-lock, unplug the connector, and install the new sensor fully seated and locked
• Restore power/water and run a test cycle; check for leaks

This upper trim strip finishes the top edge of the appliance's front opening, restoring a clean look and helping protect nearby components. Replace a cracked, missing, or loose strip to keep panels aligned and secure.

• Provides a finished edge along the upper portion of the door/face area
• Helps protect adjacent components from dust and minor splashes
• Maintains proper panel gaps and alignment
• Typical symptoms: visible cracks, warping, looseness, rattling, or exposed/sharp edges

• Disconnect power before servicing; also shut off water
• Remove the existing strip by releasing screws/clips; retain hardware for reuse
• Align the new strip and secure evenly—do not overtighten fasteners
• Check door/panel operation afterward to confirm proper fit and clearance

This O-ring is the sealing gasket between mating components, keeping fluid contained inside the system. Replacing a worn ring restores a tight, leak-free connection and helps prevent drips, moisture, and leak-related error indications.

• Creates a compressible seal between parts to prevent leaks at the joint
• Helps maintain proper system flow by stopping seepage or air ingress
• Direct replacement for rings that are flattened, cracked, brittle, swollen, or missing
• Common symptoms include dripping at the connection, moisture beneath the unit, or leak/float error alerts

• Disconnect power and shut off the water supply before servicing; wear appropriate PPE.
• Note the original ring's location; clean the groove and mating surfaces before installation.
• Apply a light coat of compatible silicone grease; avoid twisting or overstretching the ring.
• Seat evenly, reassemble, restore service, and check for leaks during a test cycle.

This metric M4 x 8 screw secures the toe-kick/lower access panel at the base of the appliance. Replace a missing or stripped fastener to keep the kickplate tight and aligned, helping prevent looseness and noise.

• Secures the toe-kick or lower access panel to the base/frame
• Restores proper fit when the original screw is lost or damaged
• Helps reduce panel rattles and vibration
• Maintains correct alignment and clearance at the bottom edge

• Disconnect power before servicing; also shut off the water supply
• Support the panel and align holes before threading the screw
• Start by hand to avoid cross-threading; tighten snugly—do not overtighten
• Verify size matches the original; replace matching hardware together if required by your model

The Pressure Chamber is an OEM part for Bosch dishwashers. This part is responsible for monitoring and controlling the water level within the dishwasher. It operates by sensing the pressure exerted by the height of the water in the tub and ensures that the dishwasher fills with the correct amount of water for optimal cleaning performance.

Causes for replacement may involve wear and tear over extended use, mineral buildup affecting the switch’s sensitivity, or electrical faults leading to inconsistent performance.  

Symptoms of a failing Pressure Chamber include:

• Overfilling or underfilling of the dishwasher, which can lead to inadequate cleaning or potential water damage.
• Unexpected changes in the wash cycle, such as sudden stops or pauses.
• The dishwasher not starting a wash cycle due to incorrect water level readings.

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

Made by Bosch. Common program control module for Bosch dishwashers SHU53/68. NOTE The manufacturer has redesigned the cover and indicator lights. Lights may be covered by the plastic case. You may have to remove the square covers over the indicator lights if needed. The same case is used for 6 and 8 indicator light models. They also no longer use the red bulb indicator lights, small surface mounted lights are used instead. If you require the Jumper Wire that goes with certain models, the part number is 00167782.

The Drive Belt is an OEM part for Bosch washing machines. This belt connects the motor to the drum, enabling the drum to spin during the wash and spin cycles. This belt measures  49.4 inches and replaces a broken or damaged original belt. With 5 ribs and 4 grooves, the high-quality belt transfers drive power to rotate the drum.

Causes of a bad drive belt include normal wear and tear over time, overloading the washer, or a misalignment of the belt and pulleys. These issues can reduce the efficiency of the washing machine and cause it to malfunction.

Symptoms of a bad drive belt include:

• The drum not spinning or agitating
• Unusual noises during operation
• Burning smell from the washer
• Washer stopping mid-cycle

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

The Water Inlet System is an OEM component specifically designed for select Bosch dishwashers. Comprising inlet valve, screens, hoses, and connectors, it precisely meters fresh water. Reliable flow prevents mineral buildups from impairing performance.

Causes of a bad water inlet system commonly involve bursting hoses or stripped connectors. Prolonged pressure weakens seals requiring timely replacement.

Symptoms of a faulty water inlet system include: 

- Fluctuating or absent water flow to spray arms
- Leaks forming inside or near the installation site
- Errors relating to improper water temperature or amounts  

Causes of a bad water inlet system involve typical degradation such as:

• Limescale clogging narrow valve openings
• Plumbing joint corrosion compromising integrity
• Splitting plastic tubing unable to withstand cycles

This OEM Bosch part is also compatible with some Miele, Blomberg, and Thermador dishwashers. 
 

Includes two rollers and axles for the upper dishwasher rack. Color: white. Each wheel measures about an inch in diameter, and with the axle clipped to it, it's about an inch wide.

The Screw is an OEM replacement part for Bosch dishwashers. Hundreds of screws hold the appliance panels and internal mechanisms securely in place. Consistent, protective enclosures ensure long-lasting performance.

Causes of a bad screw can include stripped threads from repeated tightening/loosening during repairs. Corrosion posing integrity risks may develop if water penetrates screw heads over time. 

Symptoms of a bad screw include: 

• Panels or racks that rattle or come loose during operation
• Gaps appear that allow residual moisture to seep within
• Internal components shifting position from the original assembly
• Loose wiring susceptible to abrasion posing electrical hazards

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

This sump screw secures the dishwasher's sump or sump cover to the tub, keeping the assembly tight and leak-resistant. Replace a missing, stripped, or damaged screw to restore a proper seal and stable mounting.

• Fastens the sump or sump cover to the dishwasher tub
• Helps maintain a watertight seal to reduce leaks
• Keeps filter/sump components aligned and secure
• Replaces missing, stripped, or damaged hardware
• Helps address leaks or rattling around the sump area

• Disconnect power and turn off water supply before servicing
• Remove the lower rack and filters to access the sump area
• Ensure mating surfaces and seals are clean and properly seated
• Tighten snugly by hand; do not overtighten to avoid stripping

The Ignition Device is an OEM component specifically designed for Bosch gas ranges. This device is responsible for generating the spark needed to reliably light the burners on the cooktop.

Symptoms of a faulty ignition device include:

• Inconsistent or intermittent burner ignition  
• Small flames that do not spread fully across burners
• Complete failure of one or more burners to light
• Burners extinguishing unexpectedly during use

Causes of ignition device problems tend to be worn over time from repeated use. Exposure to moisture, residue buildup, or physical impacts can also potentially damage sensitive electronic components. 

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore gas ranges and cooktops.

Includes door latch, strike plate and microswitch.

This automatic ice maker assembly forms and releases ice cubes into your refrigerator's bin, restoring steady ice production when the original unit fails. Install to resolve no-ice or incomplete harvest issues and keep ice ready when you need it.

• Freezes water in its mold and ejects cubes into the storage bin during each cycle
• Pauses production when the bin is full to prevent overflow
• Coordinates with the refrigerator control and water valve for proper fill and harvest timing
• Common symptoms include: no ice production, won't cycle/harvest, cubes jammed, or leaking/overfilling near the ice maker

• Disconnect power and turn off the water supply before servicing
• Remove the ice bin; unmount the old ice maker and unplug its connector; mount and connect the new assembly
• Align the fill tube with the ice maker's fill cup to prevent leaks
• Restore power and water; allow several hours (up to 24) for normal ice production to resume

This Button is the push-button cap for the control panel. It replaces a broken or missing button so you can reliably actuate the underlying switch and select settings as intended, restoring smooth operation and appearance.

• Presses against the internal switch to trigger functions on the control panel
• Restores proper alignment, travel, and tactile feedback when a button is worn or damaged
• Helps resolve issues such as a cracked, missing, loose, or sticking button that won't actuate selections
• Refreshes the look of the control area when the original is marred or deformed

• Disconnect power to the appliance before servicing
• Open or remove the console/control panel as required; release the old button from its clips or retainer
• Transfer any light guides, springs, or seals from the original if present; seat the new button fully
• Reassemble and test all controls for smooth movement and proper actuation

This valve magnet is the solenoid actuator used to open and close a dishwasher water/control valve, restoring proper water flow for filling and cycle operation. It replaces a failed or weak magnet to help the valve respond correctly. What it does:

• Converts electrical signal into linear motion to operate the dishwasher valve
• Restores valve opening and closing when a worn or stuck magnet causes fill or circulation issues
• Commonly used when dishwasher won't fill, stops mid-cycle, or shows related valve/fill errors
• Works with the valve body; does not include seals or the full valve assembly

• Disconnect power and shut off the water supply before beginning service
• Replace with the matching OEM magnet and ensure proper seating on the valve body
• Keep terminals dry and secure electrical connections; inspect gaskets and valve body for damage