Bosch Parts

This front door panel replaces the outer frame of the washer door, restoring appearance and proper alignment. It frames the window and interfaces with the handle/latch components so the door closes and latches as designed.

• Forms the exterior frame around the door glass and completes the door assembly
• Provides alignment for door components to help ensure smooth closing and latching
• Replaces cracked, broken, or discolored outer door trim/panel
• Can help resolve issues like loose-feeling doors or doors not aligning with the latch

• Disconnect power before servicing
• Open the door, support the assembly, and remove the perimeter screws securing the outer panel
• Transfer any components attached to the old panel, position the new panel, and tighten screws evenly
• Check door alignment and latch operation before returning the appliance to service

This door seal fits into the dishwasher's tub channel around the door opening. It compresses when the door closes to contain wash water and steam, helping prevent front-door leaks and maintain quiet, efficient operation. What it does:

• Creates a watertight seal between the dishwasher door and tub during cycles
• Helps keep water and steam from escaping; reduces operational noise
• Wear may show as drips at the door, moisture on the floor, or visible cracks/flattening
• Contributes to the door not sealing evenly

• 1 door seal

• Disconnect power and turn off the water supply before service
• Open the door, pull the old seal straight out of the channel, and clean the groove
• Warm and straighten the new seal; start at the top center and press evenly into the channel without stretching
• Close the door to help seat the seal and check for leaks on the next cycle

The Handle-Cap is an OEM part for Bosch dishwashers. It provides a contact point to open and access the dishwasher. As the cap wears through repeated use, it can impact usability.

Causes of a bad handle cap include typical wear over time. Harsh chemicals or impact can also damage this exterior part.

Symptoms of a bad handle cap are:

• Loose or improper fit that's uncomfortable
• Sharp edges or broken surfaces that could cut
• Discoloration or corrosion reducing aesthetic
• Difficulty opening the dishwasher door

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This halogen light bulb restores bright, reliable illumination in your appliance so you can clearly see the cooking area or interior. Replace a burned-out or flickering bulb to maintain visibility and safe operation. What it does:

• Provides illumination inside the appliance or over the cooking surface
• Replaces a failed halogen lamp to restore proper lighting
• Typical symptoms: light won't turn on, is dim or flickers, or works intermittently
• Helps you monitor food and check progress without guesswork

• 1 halogen lamp

• Disconnect power/unplug and allow the bulb and surrounding area to cool completely before service
• Access the lamp per your model's instructions; remove any lens or cover carefully
• Handle the new halogen bulb with gloves or a clean cloth; avoid touching the glass capsule
• Match the bulb type and rating specified for your model; do not exceed the rated wattage

The Control Board is an OEM part for Bosch dishwashers. It is the central electronic component responsible for operating and controlling all dishwasher functions. The control board receives input signals, processes commands, and directs the operation of wash cycles, motors, heating elements, and other electrical systems. 

Symptoms of a bad control board can include:

• The dishwasher is not starting or finishing cycles properly
• Lights, displays, or touchpads not working correctly 
• Strange noises coming from the dishwasher interior
• Inability to change programs or select desired cycle settings

Causes of control board failure may be due to electrical issues such as power surges, shorts, or general circuit malfunctions that can interfere with board operation over time. 

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.
 

The Drum Drive Motor is an OEM part for Bosch washing machines. This motor powers the drive system that rotates the wash drum and tumbles clothes during cycles.

Causes can be normal wear and tear over time spent rotating heavy loads daily. Failure of motor windings from years of continuous use is also common.

Symptoms of a bad drum drive motor include:

• The wash drum failing to turn or tumble clothes
• Abnormally long cycle times
• Strange noises coming from the motor area
• The machine not advancing through cycles

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

The Push Button is an OEM component specifically designed for select Bosch dishwashers. Installed on the control panel, its durable silicone-coated switch reliably operates cycles. Smooth travel withstands repeated use while maintaining tactile feedback. 

Causes of push-button failure commonly involve contact degradation from steam exposure. Cracks in the silicone introduce debris requiring periodic replacement.

Causes of a bad push button can involve:

• Unresponsive or stuck on cycles 
• Flashing error codes without cause
• Difficulty changing selected options

Symptoms of a faulty push button include intermittent operations as the controller struggles to interpret signals. Replacement ensures trouble-free functionality.

This OEM Bosch part is also compatible with some Thermador, Blomberg, and Miele dishwashers. Replace to retain convenient cycle selection through heavy usage over the appliance's lifetime.
 

The Detergent Dispenser Assembly is an OEM part for Bosch dishwashers.  The detergent dispenser assembly works with the control system to release detergent during the wash cycle.  

Causes of a bad detergent dispenser assembly can include broken or loose mounting points, a dispenser that no longer locks into place, or a damaged latch mechanism preventing the dispenser from opening.

Symptoms of a bad detergent dispenser assembly include:

• Detergent not dispensing or distributing as intended
• Dispenser door unable to close or remains open
• Excess clutter inside the dishwasher
• Ineffective cleaning or dirty dishes after cycles

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This door seal restores a tight barrier between the oven door and cavity. Replacing a worn gasket helps your oven reach and hold temperature, reduces heat escaping at the door edges, and supports more consistent baking and roasting results.

• Creates a heat-resistant seal around the oven opening
• Helps the oven preheat and maintain set temperature
• Limits heat, steam, and odors from escaping at the door
• Typical signs it needs replacement: visible tears or flattening, heat felt around the door, longer preheat/cook times, or uneven baking

• Disconnect power at the breaker and let the oven cool completely
• Open the door, pull the old seal from its channel, and clean the groove
• Press the new seal evenly into the channel without stretching; ensure corners seat fully
• Close the door to verify uniform contact all around and adjust as needed

This active carbon filter refreshes the air when your range hood is set to recirculate. Replace a saturated filter to restore effective odor reduction and maintain a more comfortable cooking space. What it does:

• Adsorbs cooking odors in recirculating operation
• Helps maintain fresher indoor air when venting back into the room
• Restores odor-removal performance when the old filter is saturated
• Typical signs it's time to replace: persistent cooking smells or diminished odor reduction

• One activated carbon filter

• Disconnect power to the hood before servicing
• Remove the metal grease filter(s) to access the charcoal filter
• Release the old filter from its clips/bayonet mount and install the new filter in the same orientation until it locks
• Charcoal filters are not washable; replace when saturated

• For hoods configured for recirculation; not used when vented to the outdoors

Restore smooth, secure door movement with this door hinge. It supports and guides the door through opening and closing, helping ensure proper alignment and consistent sealing so the appliance operates safely and efficiently.

• Supports the door's weight and pivots for smooth opening/closing
• Helps maintain correct door alignment and gasket contact
• Wear or damage can cause sagging, misalignment, noisy operation, or incomplete closing
• Replacing a worn hinge can improve door seal and overall performance

• Disconnect power and allow the appliance to cool before service
• Support the door during removal to prevent strain on the remaining hinge
• Transfer any original fasteners to the new hinge if re-used
• Check door alignment and operation before restoring power

The Foot is an OEM component specifically designed for select Bosch dryers. It securely elevates the appliance above the floor for ventilation purposes. Rigid plastic construction supports weight distribution evenly during cycles.

Causes of a bad foot can involve normal wear from long-term appliance positioning. Exposure to moisture or impacts posing cracking and weakening risks over time necessitate replacement.

Causes of a bad foot include:

• Dryer is unstable and rocks or sways more than usual
• Scratches or damage to flooring surfaces it contacts
• Uneven drying performance from improper elevation

Symptoms of a bad foot include collapsed or unstable base structure inhibiting dependable operation. Timely replacement ensures correct height positioning.

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore dryers. Replace to properly elevate your unit and maximize airflow circulation.
 

The Fan is an OEM component specifically designed for select Bosch built-in ovens. As a critical convection element, it circulates internal air currents for optimal heat distribution throughout baking and broiling cycles.

Powerful yet precisely balanced centrifugal motion agitates spacious oven cavities with homogeneous warmth. Aerodynamic fan blades expedite even cooking without hot or cold spots. 

Causes requiring replacement relate to bearing seizure or broken blade attachments disrupting designed circulation. Prolonged heat exposure may cause premature motor failure or cracked housings to no longer sustain needed speeds.

Symptoms signaling the need for a new fan include:

• Inability to effectively circulate air for simultaneous multi-rack cooking  
• Louder than average operation noise accompanied by vibration
• Erratic or ineffective temperature management within cycles

This OEM Bosch replacement fan is also compatible with Thermador, Gaggenau, and some Kenmore built-in ovens employing convection methods. Proper reinstallation restores designed air transfer capabilities for perfect results.
 

The Hook is an OEM part for Bosch microwave doors. Manufactured from heat resistant composite materials, it firmly holds the door closed during cooking cycles.  

Causes of a faulty latch/hook include failures of being worn down from repetitive opening/closing motions over time. Exposure to high heat or abrasive cleaners also leads to decreased functionality.

Symptoms of a damaged latch/hook involve:

• Doors not sealing fully or locking properly
• Failure to open after cooking
• Degrading latch fittings allowing moisture or debris entry

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

The Drain Pump Cover is an OEM part for Bosch dishwashers. This cover protects the drain pump mechanism from debris while draining dirty water after each cycle.

Causes of a bad drain pump cover include cracks or breaks from heavy impacts over time.

Symptoms of an improperly functioning cover include:

• Leaks in the area around the drain pump
• Decreased drain and pump performance over time
• Potential clogs from broken pieces inside

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

Restore your dishwasher's top loading area with this upper dishrack. Replacing a damaged or rusted rack helps keep glasses, mugs, and small plates secure and properly positioned for smooth sliding and consistent wash coverage.

• Holds and organizes cups, glasses, bowls, and small plates on the upper level
• Slides along the upper rails for easy loading and unloading
• Maintains correct spacing for effective spray coverage and drying
• Common replacement for rusted wire, broken/missing tines, or a rack that falls off the rails or binds

• Turn off power at the breaker and let the dishwasher interior cool before servicing
• Open the door; release/flip the upper rail end caps or stops per your model
• Slide the old rack out; transfer any removable accessories if needed
• Slide the new rack into the rails and reinstall the stops; verify smooth travel