Parts for Ge GMR05BLHCSCA: Cabinet Parts

Dissolves limescale, mineral deposits, and odor-causing residues from dishwasher tub and spray system. Use monthly to maintain peak cleaning performance.

Replaces the protective top cover for your dishwasher control box housing. Needed when the original is cracked, broken, or missing to keep electronics enclosed.

Converts older 3-piece washer support apron to one-piece design. Replaces sagging, bent, or broken apron brackets that cause motor clearance issues.

Replacement vent and condenser fan assembly for dishwashers. Installs in the base to circulate air for drying. Replace if broken, cracked, or missing.

Replacement end cap for washer left-side assembly. Secures cabinet alignment and protects internal components. Needed when original is cracked or missing.

Replaces a short wireform hinge that secures your washer lid or access panel. Order a new hinge if yours is rusted, bent, cracked, or missing.

Grounding stud for top-load washers. Connects electrical ground wire to washer frame. Replace if stripped, corroded, or missing for proper grounding.

Size: 1/4 - 20 b.

Size: 8-18 b.

Self-leveling bracket for top-load washers. Mounts to the base to stabilize the unit. Replace if broken, bent, or missing to restore proper leveling.

Hex washer head screw for washer pedestals. Secures pedestal components and panels. Replace if screw is stripped, missing, or damaged during assembly.

Protective conduit sleeve for washer electrical wiring. Installs between control panel and base. Replace if cracked, worn, or missing to protect wires.

Left apron bracket for washers. Secures the apron panel to the washer cabinet. Replace if cracked, broken, or missing to restore proper panel support.

Right side apron bracket for washers. Secures the apron panel to the washer cabinet. Replace if cracked, bent, or broken to restore proper panel support.

5/16-18 tpt ihw s n

This zinc-plated screw secures the power control board and other electrical components inside your washing machine. The specific threading and length ensure proper mounting and electrical grounding of control circuits. Replace this fastener if the control board is loose, vibrating, or if the original screw is stripped or missing.

Stainless steel hex washer head screw for securing appliance panels, brackets, and trim. Replace missing, stripped, or corroded fasteners during repair.

Protects the washer's inner drum edge and prevents clothing from snagging on the tub lip. Replace if cracked, broken, or missing to avoid fabric damage.

Alignment pin keeps washer door hinge positioned so the door closes evenly. Replace if cracked, bent, or missing to restore proper door fit and seal.

Secures washer tub and hoses to prevent leaks and noise. Replace if worn or broken to maintain proper alignment and seal. Verify fit with your model.

Right-side cabinet end cap for washers. Replaces cracked, broken, or missing trim piece. Restores proper fit and protects internal components.

This washer front panel assembly replaces a cracked, worn, or damaged console face. Restores appearance and provides housing for control buttons.

Push-in plug button for top-load washers. Snaps into trim openings to cover unused holes and restore a clean finish. Replace if cracked or missing.

Size: 8 - 18 ab.

Snap-in plastic clip cover that conceals fasteners and secures panels on your top-load washer. Replace if broken or missing to restore appearance.

A single replacement screw used to secure appliance panels, trim, and internal brackets so components stay aligned and reduce rattling. Simple, direct-fit fastener for restoring proper mounting and stable operation. What it does:

• Secures panels, mounting brackets, trim pieces and other appliance components
• Helps stop rattling, vibration, or loose panels caused by missing or stripped fasteners
• Restores proper alignment of doors and access panels when original screw is lost or damaged
• Matches the OEM fastening point for a straightforward hardware replacement

• Disconnect power to the appliance before working on electrical components or access panels
• Use the correct screwdriver to avoid stripping the head; match drive type to the screw
• Tighten firmly but do not overtighten—stop when snug to avoid damaging threads or parts
• Keep removed fasteners organized and compare with the replacement to ensure correct fit

Routes exhaust air from your dishwasher through the proper ventilation channel. Replace if damaged, crushed, or disconnected. Verify fit with your model.

This top attachment strip secures the appliance's top panel and provides the mounting point for the door strike, restoring a stable, properly aligned front. It prevents panel movement and reduces rattles for a snug fit and reliable door engagement. What it does:

• Secures the top/front panel to the cabinet to maintain alignment and fit
• Serves as the mounting point for the door strike or latch components
• Helps eliminate rattling, vibration, and gaps at the top of the door area
• Restores reliable door engagement and prevents the strike from shifting

• Disconnect power to the appliance before beginning any repair
• Remove the top panel or access screws to reach the attachment strip; a screwdriver set is typically required
• Handle mounting tabs and edges carefully to avoid bending or damage
• Verify alignment of the door strike and test door closure after installation

Replaces the inner-facing panel of your dishwasher door. Restores a clean barrier and protects the outer assembly from damage, cracks, or heavy staining.

Protective lower housing for dishwasher control electronics. Replaces cracked, broken, or missing base covers. Shields wiring and components from debris.

Secures your dishwasher door to the cabinet as a stable pivot point. Replace this bracket if cracked, broken, or worn to restore proper door alignment.

Secures and aligns the dishwasher door hinge assembly. Replace if your hinge bracket is cracked, bent, or broken to restore proper door fit and movement.

Dark grey exterior vent cover that replaces a cracked, faded, or missing dishwasher vent. Restores appearance and protects the vent opening.

Size: 8-32 t. Includes 12 screws.

8-18 hi/lo 5/8

Fix a washer that won't spin or hums but doesn't start. This single-speed motor replacement restores spin cycles when the motor windings fail.

Restore your appliance's factory look with this badge assembly. It replaces a missing, cracked, or faded logo on the refrigerator exterior, delivering a clean, professional appearance without affecting performance or operation.

• Decorative nameplate/logo for the refrigerator exterior
• Replaces cracked, faded, loose, or missing badge
• Restores a clean, factory appearance
• Cosmetic component; does not impact cooling or function

• Disconnect power before servicing the appliance
• Protect the finish; use a plastic trim tool to remove the old emblem if needed
• Clean and dry the mounting area; align with locating marks/holes and secure per your model diagram

Fix squealing noises during the drying cycle or moisture buildup. This vent fan assembly removes humid air and helps dishes dry properly in your dishwasher.

The Wire Tie is an OEM part for GE dryers. It is used to secure and organize internal wiring, ensuring that wires remain properly positioned and do not interfere with the operation of the dryer. This part plays an important role in preventing wires from becoming tangled, pinched, or damaged during the dryer’s cycles.

Over time, the wire tie can become worn out, broken, or damaged due to prolonged exposure to heat, vibrations, or wear from normal use. A compromised wire tie can lead to loose or unsecured wiring, which may impact the performance of the dryer or cause electrical issues.

Symptoms of a bad Dryer Wire Tie include:

• Loose or unsecured internal wiring
• Interference with dryer components during operation
• Electrical malfunctions or short circuits
• Wires appearing frayed or damaged due to improper support

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Replace your missing or damaged dishwasher toe kick insulation panel. Blocks drafts and protects internal components. Easy DIY installation repair.

This machine screw secures panels, brackets, and internal components in compatible washers. Replacing a missing or stripped fastener restores a tight fit to help reduce vibration and keep parts properly aligned.

• 10-32 thread; 5/8-inch length; Torx T25 drive
• Fastens components and panels to resist loosening from vibration
• Replaces lost, corroded, or stripped screws
• Helps address loose or rattling panels, misalignment, or hardware that won't tighten

• Unplug the appliance and turn off water supply before servicing
• Use a T25 Torx driver; start threads by hand to avoid cross-threading
• Tighten snugly; do not overtighten
• Repair or replace the bracket/panel for a secure hold

Secures the drive pulley to the transmission shaft in top-load washers. Replace if the original nut is backing off, stripped, or missing.

Plastic bushing that fits inside your washer's lid hinge for smooth pivoting. Replace if worn, cracked, or causing lid misalignment and squeaking.

Secures your washer's drain hose to the standpipe or laundry tub. Replace if cracked, broken, or missing to keep hose positioned and prevent dislodging.

Detergent not dispensing during wash cycle? This dishwasher detergent dispenser plate holds and releases detergent at the right time for proper cleaning.

Cushions where the washer lid meets the top panel to soften closure and protect the finish. Replace worn, cracked, or missing bumpers to reduce noise.

Adjustable leveling leg threads into washer base to stabilize cabinet and reduce vibration. Replace if cracked, broken, or missing for proper support.

Replaces a cracked or leaking wash tub to restore water containment and drum support. Fixes leaks, rubbing noises, and vibration. Confirm fit by model.

Left-hand attachment strip secures trim and panels on your dishwasher for a clean, finished appearance. Replace if cracked, broken, or missing.

Dissolves limescale, mineral deposits, and odor-causing residues from dishwasher tub and spray system. Use monthly to maintain peak cleaning performance.

Double-style bushing supports the washer lid hinge pin. Replace worn or cracked bushings to restore smooth, quiet lid operation and proper alignment.

This locking clip secures a mating part—often a control knob—onto its shaft on select laundry appliances. Replacing a worn or missing clip restores a tight fit so controls stay in place and operate as intended during use.

• Locks a knob, lever, or similar component onto its shaft/post to prevent it from slipping off
• Maintains a firm fit to reduce wobble and intermittent control engagement
• Replace if the clip is bent, fatigued, corroded, or missing
• Typical symptoms include a knob that falls off, feels loose, or spins without engaging

• Disconnect power to the appliance; turn off water supply for washers
• Pull the affected component straight off to access the clip
• Use needle-nose pliers to remove/install the clip; avoid deforming it
• Ensure the clip is fully seated; test for a snug fit before reassembly

Secures hoses to fittings for leak-free operation. Replace when worn or corroded to stop drips on fill, drain, or circulation lines. Confirm fit.

Size: 10-32 GXTT FLP.595 S

Secures washer hoses at pump, tub, and valve connections to prevent leaks and hose blow-offs. Replace worn or missing clamps for a tight seal. Confirm fit.

Secures hoses and tubing in your dishwasher to prevent leaks and ensure proper water flow. Replace if you notice water dripping or leaking around connections. Verify fit with your model number before ordering.

Seals the flood/overflow hose connection to your washer tub. Replace if water seeps from the tub area or the gasket feels soft. Confirm fit by model.

Holds tub dampening straps in place on your washer. Replace if cracked, broken, or worn from heavy loads. Includes installation video guide.

This is a screw and flat washer set used to secure the drum baffles (lifters) inside a dryer drum. The baffles tumble clothing during the drying cycle, and these fasteners keep them firmly attached. Replace if the screws are stripped, missing, or corroded, which can cause baffles to come loose and create rattling noises during operation.

Front lower trim panel that covers the dishwasher base. Replace if cracked, damaged, missing, or to refresh appearance. Direct-fit cover piece.

Secures your washer's drain hose to standpipe, maintaining proper air gap to prevent siphoning and backflow. Replace if clip is broken or missing.

Mounting screw for washer components. Secures drain hose clamps, panels, and internal parts. Replace if missing, stripped, or lost during repair.

Suspension rod and spring assembly for washing machines. Installs between the tub and cabinet frame. Replace when cracked, broken, or worn to restore stability.

Plastic support bracket that secures suspension rods to the washer cabinet. Replace when cracked, broken, or worn to restore proper drum suspension.

Fix washer overfilling or not filling properly. This pressure switch controls water level for proper washing. DIY-friendly, takes about 5-10 minutes.

Guides water from the inlet valve into the wash tub. Replace if cracked, broken, leaking, or causing uneven water distribution in your top-load washer.

The screw is an OEM replacement component for GE dishwashers. It is used to securely fasten parts inside the dishwasher tub assembly.

Causes of a damaged or defective screw usually involve wear from continuous mechanical stresses and vibration during dishwasher usage. Loose parts affect machine balance and performance.

Symptoms of a compromised screw placement include:

• Noises or abnormal sounds coming from inside the tub  
• Intermittent error codes related to moving components
• Detached or misaligned spray arms or filters
• Insecure tub fixtures that can be jarred with normal operation 

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 

The GE screw is an OEM replacement part responsible for securing various components or parts together on a washing machine. Its main function is to connect and hold together various parts, panels, or brackets, ensuring that they remain securely in place during the appliance's operation. The screw comes in the size 1/4-20 MCH HXW 5/8 S, indicating its thread size, head type, and length.

This part fixes the following symptoms:

• Loose or wobbly components on the washing machine
• Difficulty in assembling or disassembling parts due to missing or faulty screws
• Certain parts becoming detached or separating during use
• The washing machine vibrating excessively during use
• Doors, panels, or knobs not staying securely in place

The GE washing machine screw can also be used on Hotpoint, RCA, and Kenmore/Sears appliances.

Secure your dishwasher to the underside of countertops with this screw and button plug kit. Replace stripped, missing, or damaged fasteners.

Replaces worn, cracked, or missing side trims along the dishwasher tub opening. Restores a clean finish and allows the door to open smoothly.

Suspension rod and spring assembly for washer drum stability. Replaces worn, broken, or weakened suspension components causing drum movement or sagging.

Fix a washer that won't advance through cycles or skips fill/agitate steps. This timer controls cycle sequencing. DIY repair in about 30 minutes.

Fabric softener not dispensing or agitator loose? This washer dispenser cup sits atop the agitator. Simple DIY fix—twist off and replace in minutes.

Washer won't spin or agitate? A faulty lid switch prevents operation when the lid isn't closed. DIY-friendly repair, typically takes 10-15 minutes.

Drain pump inlet hose for top-load washers. Connects the tub to the pump assembly. Replace if cracked, leaking, or has holes causing water on the floor.

Fix a washer that won't spin or agitate. This motor capacitor stores energy to start and run the motor. DIY repair takes about 10 minutes with video help.

The Compression Ring is an OEM part for GE washing machines. This ring is essential for securing the tub within the washing machine, ensuring it remains in place during the wash and spin cycles. It helps maintain the stability and proper function of the washing machine.

You should replace the compression ring if it becomes worn, cracked, or damaged. Causes of a bad compression ring can include frequent use, high-stress loads during wash cycles, or physical damage, which can lead to instability and poor washing performance.

Symptoms of a bad compression ring include:

• Excessive shaking or movement of the washing machine during cycles
• Unusual noises during operation
• The washing machine tub appearing misaligned or loose
• Ineffective washing due to instability

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Secures your dishwasher underneath the kitchen countertop. Replace if the bracket is cracked, broken, bent, or missing from installation.

The Door Latch Strike is an OEM part for GE dishwashers. It ensures the dishwasher door latches securely, allowing the appliance to operate only when the door is properly closed.

Causes of a bad door latch strike can include wear and tear from regular use, damage from slamming the door, or misalignment due to repeated opening and closing.

Symptoms of a bad door latch strike include:

• The dishwasher door not latching securely
• The dishwasher not starting or stopping mid-cycle
• Leaks around the door during operation
• Difficulty in closing the door properly

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Controls airflow in your dishwasher door. Replace if cracked or if you see leaking from the door vent area. Confirm fit with your model number.

The Knob Clip is an OEM part for GE washing machines and dryers. This small but crucial component is designed to secure the control knob to the appliance's control panel.  

Over time, knob clips can wear out or break due to frequent use or accidental damage. When this happens, the control knob may become loose, fall off easily, or fail to engage the control panel properly, making it difficult to set the appliance to the desired cycle or function.

Symptoms of a bad Knob Clip include:

• The control knob is loose or falls off the panel easily.
• Difficulty in adjusting settings due to a loose knob.
• The knob does not stay in place or slips when turned.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

Connects the pressure switch to the tub in top-load washers. Replace if cracked, punctured, or brittle to restore proper water level monitoring.

Washer won't fill, leaks after cycles, or has no hot water? The triple water valve controls fill, rinse, and dispenser flow. DIY fix in under 1 hour.

The Drain Hose Clip is an OEM part for GE washing machines. It secures the drain hose to the back of the washer, preventing it from becoming dislodged during operation. This ensures that water is properly directed out of the washer and into the household drain system, preventing leaks and water damage.

Causes of a bad drain hose clip can include wear and tear from regular use, damage from improper handling during installation or maintenance, or breakage due to repeated stress and movement of the washer.

Symptoms of a bad drain hose clip include:

• Water leaking from the back of the washer
• Drain hose detaching or becoming loose during operation
• Difficulty securing the drain hose in place
• Visible damage or cracking on the clip

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Note: For the entire drain hose, use part number WH41X10096.

Washer won't agitate or spins but doesn't clean clothes? The agitator coupler connects the agitator to the drive shaft. Easy DIY repair with video guide.

Timer dial knob for washers. Installs on control panel to select wash cycles. Replace if knob spins freely, teeth are worn, or it won't engage cycles.

Secures the timer knob to the shaft for accurate cycle selection. Replace if worn, broken, or lost causing knob to spin freely. Confirm fit with model.

Replacement silverware basket for dishwasher lower rack. Holds and organizes utensils during wash cycles. Order if your basket is cracked or broken.

Hub washer fits between the transmission and inner tub in top-load washers. Replace if cracked, worn, or causing leaks during operation.

Replace your washer drive belt if the drum won't spin or agitate. Connects motor to drum for proper washing cycles. Confirm fit with your model number.

Washer won't drain or leaves clothes soaking wet? This drain pump removes water from the tub after each cycle. Typical DIY repair takes 20-30 minutes.

The Hub Nut is an OEM part for GE washing machines. This component secures the inner tub to the drive mechanism, ensuring that it remains in place during the agitation and spinning cycles. This lock-down nut is reverse threaded, meaning that it is loosed by rotating it clockwise. For easier removal of the old nut, it is recommended to use the tub nut spanner wrench WX5X1325.

Symptoms of a bad Hub Nut include:

• Unusual noises like banging or grinding during the spin cycle.
• The inner tub moving excessively or becoming loose.
• Leakage around the center of the machine, indicating a seal failure possibly related to a loose hub nut.
• Inefficiency in spinning or agitating clothes properly.

Causes of a bad hub nut can include corrosion due to exposure to water and detergent, improper initial installation, or loosening over time from the vibration and movement of the washing machine.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Replaces broken or worn tub dampening straps that stabilize your washer's inner tub during operation. Restores proper suspension to reduce vibration.

Replacement drain hose for top-load washers. Connects washer to household drainage system. Replace if cracked, leaking, crushed, or missing.

Fix a washer that won't agitate or has broken fins. This agitator assembly snaps in place in under 5 minutes. Simple DIY repair, no tools required.

This is a white plastic control knob that attaches to the timer or cycle selector shaft on the dryer's control panel. It allows you to select the desired drying cycle or timer setting. Replace this knob if it is cracked, broken, or if the shaft connection has worn out so the knob spins without engaging the timer.

Replacement tub bearing for top-load washers. Fixes grinding, roaring, or loud humming noises during spin cycles. Verify fit with your model number.

Supports the inner tub for smooth rotation during wash and spin cycles. Replace if you hear loud grinding noise or see oil stains. Verify fit by model.

This Tub Seal is an OEM replacement part for GE washing machines that is responsible for preventing water from leaking from the tub. This part is located at the base of the washing machine tub and creates a seal between the tub and the transmission to prevent water from leaking out during the wash cycle. 

This part fixes the following symptoms-

• Water leaking from the underside of the washing machine.
• A musty or mildew smell coming from the machine.
• Unusual noises during use. 

Causes of a bad tub seal can range from normal wear and tear to a misaligned tub or an overloaded washing machine, which puts extra pressure on the seal. Additionally, the buildup of hard water minerals can degrade the seal's material over time.

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 

Replacement timer control knob assembly for washers. Installs on control panel to select cycles and settings. Needed when knob is cracked, broken, worn, or won't grip timer shaft.

This is the flexible rubber or vinyl gasket that lines the opening of your dishwasher tub, creating a watertight seal when the door is closed during a wash cycle. It prevents water from leaking out around the door during operation. Replace it when you notice water pooling on the floor in front of your dishwasher, or when the gasket is visibly torn, stiff, or pulled away from the tub.

Dishwasher won't start or run? A faulty door latch prevents cycles from beginning. This latch assembly secures the door and activates switches. 5-10 min fix.

Dissolves limescale, mineral deposits, and odor-causing residues from dishwasher tub and spray system. Use monthly to maintain peak cleaning performance.