Parts for Ge PTAN6250M0WT: Controls Parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Sound dampening insulation pack for washers. Installs inside cabinet to reduce noise and vibration. Replace if torn, compressed, or missing pieces.

This right-side end cap is the molded exterior trim piece that finishes the appliance cabinet and protects internal edges. It restores a clean, finished appearance and helps keep door and panel seams sealed from dirt and moisture. What it does:

• Covers and protects the outer edge on the right side of the cabinet, preventing exposure of internal components
• Restores a flush, factory-finish look when a cracked or missing end cap causes gaps or rough edges
• Helps maintain proper panel alignment and visual symmetry on the appliance exterior
• Reduces dirt and moisture intrusion where panels meet, supporting overall cabinet integrity

• One right-side end cap (white), as shown

• Designed for snap- or screw-fit installation; remove power and follow manufacturer disassembly steps before replacing
• Verify orientation (right side) and matching color before starting; handle trim pieces gently to avoid cracking
• Use basic hand tools; keep fasteners and any retainer clips for reuse or replace if damaged

Converts older 3-piece washer support apron to one-piece design. Replaces sagging, bent, or broken apron brackets that cause motor clearance issues.

Secures the counterweight to the washer drum assembly. Replace this bracket if it's cracked, broken, or causing rattling during wash cycles.

6-20 x 3/8 in. screw secures panels and brackets inside washers. Replaces missing, stripped, or damaged fasteners to restore proper fit and stability.

Replacement plug insert for washer control panels and cabinet surfaces. Snaps into pre-drilled holes to cover openings or secure components. Needed when original plug is missing, cracked, or broken.

Protective conduit sleeve for washer electrical wiring. Installs between control panel and base. Replace if cracked, worn, or missing to protect wires.

Left apron bracket for washers. Secures the apron panel to the washer cabinet. Replace if cracked, broken, or missing to restore proper panel support.

Right side apron bracket for washers. Secures the apron panel to the washer cabinet. Replace if cracked, bent, or broken to restore proper panel support.

Concrete counterweight that attaches to the washer tub to stabilize the drum during spin cycles. Replace if cracked, broken, or missing pieces.

Wire tie retainer for refrigerators. Secures and organizes internal wiring. Replace if cracked, broken, or missing to keep wires properly bundled.

Hex washer head screw for washer pedestals. Secures pedestal components and panels. Replace if screw is stripped, missing, or damaged during assembly.

Self-leveling bracket for top-load washers. Mounts to the base to stabilize the unit. Replace if broken, bent, or missing to restore proper leveling.

Size: 1/4 - 20 b.

Size: 8-18 b.

Replaces a short wireform hinge that secures your washer lid or access panel. Order a new hinge if yours is rusted, bent, cracked, or missing.

Grounding stud for top-load washers. Connects electrical ground wire to washer frame. Replace if stripped, corroded, or missing for proper grounding.

Secures washer tub and hoses to prevent leaks and noise. Replace if worn or broken to maintain proper alignment and seal. Verify fit with your model.

Alignment pin keeps washer door hinge positioned so the door closes evenly. Replace if cracked, bent, or missing to restore proper door fit and seal.

Stainless steel hex washer head screw for securing appliance panels, brackets, and trim. Replace missing, stripped, or corroded fasteners during repair.

This zinc-plated screw secures the power control board and other electrical components inside your washing machine. The specific threading and length ensure proper mounting and electrical grounding of control circuits. Replace this fastener if the control board is loose, vibrating, or if the original screw is stripped or missing.

1/4-20 hex washer head screw for washers. Secures panels, brackets, and internal components. Replace missing, stripped, or damaged mounting hardware.

5/16-18 tpt ihw s n

This washer front panel assembly replaces a cracked, worn, or damaged console face. Restores appearance and provides housing for control buttons.

Snap-in plastic clip cover that conceals fasteners and secures panels on your top-load washer. Replace if broken or missing to restore appearance.

Size: 8 - 18 ab.

Push-in plug button for top-load washers. Snaps into trim openings to cover unused holes and restore a clean finish. Replace if cracked or missing.

A single replacement screw used to secure appliance panels, trim, and internal brackets so components stay aligned and reduce rattling. Simple, direct-fit fastener for restoring proper mounting and stable operation. What it does:

• Secures panels, mounting brackets, trim pieces and other appliance components
• Helps stop rattling, vibration, or loose panels caused by missing or stripped fasteners
• Restores proper alignment of doors and access panels when original screw is lost or damaged
• Matches the OEM fastening point for a straightforward hardware replacement

• Disconnect power to the appliance before working on electrical components or access panels
• Use the correct screwdriver to avoid stripping the head; match drive type to the screw
• Tighten firmly but do not overtighten—stop when snug to avoid damaging threads or parts
• Keep removed fasteners organized and compare with the replacement to ensure correct fit

Secures washer components with a molded sleeve that protects surfaces and reduces vibration. Replace if cracked, worn, or missing to restore secure fit.

8-18 hi/lo 5/8

Size: 8-32 t. Includes 12 screws.

Power line filter sits between household AC and washer's internal wiring. Replace when cracked, corroded, or causing breaker trips due to electrical noise.

Fix scraping noise during agitation or poor cleaning with a new washer pulsator. Directs water flow and clothing movement. Takes about 10 minutes to replace.

This machine screw secures panels, brackets, and internal components in compatible washers. Replacing a missing or stripped fastener restores a tight fit to help reduce vibration and keep parts properly aligned.

• 10-32 thread; 5/8-inch length; Torx T25 drive
• Fastens components and panels to resist loosening from vibration
• Replaces lost, corroded, or stripped screws
• Helps address loose or rattling panels, misalignment, or hardware that won't tighten

• Unplug the appliance and turn off water supply before servicing
• Use a T25 Torx driver; start threads by hand to avoid cross-threading
• Tighten snugly; do not overtighten
• Repair or replace the bracket/panel for a secure hold

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

The Wire Tie is an OEM part for GE dryers. It is used to secure and organize internal wiring, ensuring that wires remain properly positioned and do not interfere with the operation of the dryer. This part plays an important role in preventing wires from becoming tangled, pinched, or damaged during the dryer’s cycles.

Over time, the wire tie can become worn out, broken, or damaged due to prolonged exposure to heat, vibrations, or wear from normal use. A compromised wire tie can lead to loose or unsecured wiring, which may impact the performance of the dryer or cause electrical issues.

Symptoms of a bad Dryer Wire Tie include:

• Loose or unsecured internal wiring
• Interference with dryer components during operation
• Electrical malfunctions or short circuits
• Wires appearing frayed or damaged due to improper support

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Secures the drive pulley to the transmission shaft in top-load washers. Replace if the original nut is backing off, stripped, or missing.

Plastic bushing that fits inside your washer's lid hinge for smooth pivoting. Replace if worn, cracked, or causing lid misalignment and squeaking.

Secures your washer's drain hose to the standpipe or laundry tub. Replace if cracked, broken, or missing to keep hose positioned and prevent dislodging.

Cushions where the washer lid meets the top panel to soften closure and protect the finish. Replace worn, cracked, or missing bumpers to reduce noise.

Adjustable leveling leg threads into washer base to stabilize cabinet and reduce vibration. Replace if cracked, broken, or missing for proper support.

Plastic housing that secures the drain solenoid to the pump assembly. Replace if cracked, broken, or missing to properly position the solenoid mechanism.

Replaces a cracked or leaking wash tub to restore water containment and drum support. Fixes leaks, rubbing noises, and vibration. Confirm fit by model.

Double-style bushing supports the washer lid hinge pin. Replace worn or cracked bushings to restore smooth, quiet lid operation and proper alignment.

This locking clip secures a mating part—often a control knob—onto its shaft on select laundry appliances. Replacing a worn or missing clip restores a tight fit so controls stay in place and operate as intended during use.

• Locks a knob, lever, or similar component onto its shaft/post to prevent it from slipping off
• Maintains a firm fit to reduce wobble and intermittent control engagement
• Replace if the clip is bent, fatigued, corroded, or missing
• Typical symptoms include a knob that falls off, feels loose, or spins without engaging

• Disconnect power to the appliance; turn off water supply for washers
• Pull the affected component straight off to access the clip
• Use needle-nose pliers to remove/install the clip; avoid deforming it
• Ensure the clip is fully seated; test for a snug fit before reassembly

Secures washer hoses at pump, tub, and valve connections to prevent leaks and hose blow-offs. Replace worn or missing clamps for a tight seal. Confirm fit.

1/4-20 x 5/8 hex washer-head machine screw secures brackets, panels, and internal components. Replace worn, stripped, or missing fasteners.

Seals the flood/overflow hose connection to your washer tub. Replace if water seeps from the tub area or the gasket feels soft. Confirm fit by model.

Holds tub dampening straps in place on your washer. Replace if cracked, broken, or worn from heavy loads. Includes installation video guide.

Drive pulley mounts to the washer basket shaft and routes the belt from the motor. Replace if worn, cracked, loose, or showing play on the shaft.

This is a screw and flat washer set used to secure the drum baffles (lifters) inside a dryer drum. The baffles tumble clothing during the drying cycle, and these fasteners keep them firmly attached. Replace if the screws are stripped, missing, or corroded, which can cause baffles to come loose and create rattling noises during operation.

Secures your washer's drain hose to standpipe, maintaining proper air gap to prevent siphoning and backflow. Replace if clip is broken or missing.

The Lid Assembly is an OEM part for GE washing machines. This part is the lid of the washer. It is essential for securely covering the washer drum, preventing water from splashing out during the wash cycle, and allowing safe operation by ensuring the washer does not run with the lid open.

Causes of a bad lid assembly can include general wear and tear, physical damage from heavy loads or impacts, or issues with the hinges or latch mechanisms.

Symptoms of a bad lid assembly include:

• Difficulty in opening or closing the lid
• Washer not starting or stopping mid-cycle due to a faulty lid switch
• Visible cracks or damage on the lid
• Water leaking from the top of the washer

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

Mounting screw for washer components. Secures drain hose clamps, panels, and internal parts. Replace if missing, stripped, or lost during repair.

Suspension rod and spring assembly for washing machines. Installs between the tub and cabinet frame. Replace when cracked, broken, or worn to restore stability.

Fix grinding or scraping noise during agitation with this washer pulsator coupling. Located under the agitator, connects to drive shaft. DIY repair in 10 minutes.

Plastic support bracket that secures suspension rods to the washer cabinet. Replace when cracked, broken, or worn to restore proper drum suspension.

Installation tool designed for installing washer drive belts. Provides proper leverage and positioning to seat belts correctly on pulleys and motor shafts.

The Mode Shifter & Shaft Assembly is an OEM replacement part for GE washing machines. It is a mechanical component located inside the washer tub that allows for shifting between agitation, spin, and other cycles. The mode shifter and shaft assembly receive input from the control system to precisely change the operational mode at designated points in the cycle.

Causes of a bad mode shifter & shaft assembly include worn out or damaged internal gears, stripped or broken shafts, or a loss of integrity in components that restrict smooth shifting between modes.

Symptoms of a bad mode shifter & shaft assembly include:

• Inability to start or change wash cycles
• The washer getting stuck in one mode of operation
• Grinding noises and vibrations during cycle shifts
• Premature ending of cycles

This GE OEM replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Washer won't spin or agitate? A faulty lid switch magnet may be the cause. This part signals the switch that the lid is closed. Easy 20-minute DIY fix.

Suspension rod and spring assembly for washer drum stability. Replaces worn, broken, or weakened suspension components causing drum movement or sagging.

Fix no hot water, leaking when washer is off, or weak water pressure. This triple water inlet valve controls hot, cold, and warm water flow. DIY-friendly repair.

Drain pump inlet hose for top-load washers. Connects the tub to the pump assembly. Replace if cracked, leaking, or has holes causing water on the floor.

The washer start stop switch button is the physical push button on your washing machine's control panel that signals the machine to begin or pause a cycle. It connects to the underlying switch mechanism that sends an electrical signal to the control system. Replace this part when pressing the button does nothing, the button feels mushy or broken, or the washer will not start or stop responding to that control.

Connects the pressure switch to the tub in top-load washers. Replace if cracked, punctured, or brittle to restore proper water level monitoring.

Washer won't spin or agitate? This lid switch assembly detects if the lid is closed. Moderate DIY repair—front panel removal required. Video available.

The Drain Hose Clip is an OEM part for GE washing machines. It secures the drain hose to the back of the washer, preventing it from becoming dislodged during operation. This ensures that water is properly directed out of the washer and into the household drain system, preventing leaks and water damage.

Causes of a bad drain hose clip can include wear and tear from regular use, damage from improper handling during installation or maintenance, or breakage due to repeated stress and movement of the washer.

Symptoms of a bad drain hose clip include:

• Water leaking from the back of the washer
• Drain hose detaching or becoming loose during operation
• Difficulty securing the drain hose in place
• Visible damage or cracking on the clip

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Note: For the entire drain hose, use part number WH41X10096.

Hub washer fits between the transmission and inner tub in top-load washers. Replace if cracked, worn, or causing leaks during operation.

Washer won't drain or leaves clothes soaking wet? This drain pump removes water from the tub after each cycle. Typical DIY repair takes 20-30 minutes.

The Hub Nut is an OEM part for GE washing machines. This component secures the inner tub to the drive mechanism, ensuring that it remains in place during the agitation and spinning cycles. This lock-down nut is reverse threaded, meaning that it is loosed by rotating it clockwise. For easier removal of the old nut, it is recommended to use the tub nut spanner wrench WX5X1325.

Symptoms of a bad Hub Nut include:

• Unusual noises like banging or grinding during the spin cycle.
• The inner tub moving excessively or becoming loose.
• Leakage around the center of the machine, indicating a seal failure possibly related to a loose hub nut.
• Inefficiency in spinning or agitating clothes properly.

Causes of a bad hub nut can include corrosion due to exposure to water and detergent, improper initial installation, or loosening over time from the vibration and movement of the washing machine.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Replaces broken or worn tub dampening straps that stabilize your washer's inner tub during operation. Restores proper suspension to reduce vibration.

Replace your top-load washer drive belt when you hear squealing, see the drum not spinning, or notice wear. Connects motor to drum for wash cycles. Verify fit with your model number.

Replacement drain hose for top-load washers. Connects washer to household drainage system. Replace if cracked, leaking, crushed, or missing.

Replacement tub bearing for top-load washers. Fixes grinding, roaring, or loud humming noises during spin cycles. Verify fit with your model number.

Supports the inner tub for smooth rotation during wash and spin cycles. Replace if you hear loud grinding noise or see oil stains. Verify fit by model.

This Tub Seal is an OEM replacement part for GE washing machines that is responsible for preventing water from leaking from the tub. This part is located at the base of the washing machine tub and creates a seal between the tub and the transmission to prevent water from leaking out during the wash cycle. 

This part fixes the following symptoms-

• Water leaking from the underside of the washing machine.
• A musty or mildew smell coming from the machine.
• Unusual noises during use. 

Causes of a bad tub seal can range from normal wear and tear to a misaligned tub or an overloaded washing machine, which puts extra pressure on the seal. Additionally, the buildup of hard water minerals can degrade the seal's material over time.

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.