Crosley Parts

• Will not agitate
• Spins slowly

I had previously replaced the pump about 1 year ago. That was not the problem. Still leaked the same way - intermittently, but always in the center of the washer onto the floor. None of the hoses were leaking - no evidence of corrosion or water mineral residue at any of the hose fittings. So, it must have been something else. I studied the parts diagram for the washer tub assembly and concluded the source of the leak almost had to be the outer tub's Centerpost Gasket. It was really the... Read more

• Doesn't shut off
• Won't start
• Will not tumble

I realized my load of laundry was still wet after a normal drying cycle. My first action was to turn the dryer on (2010 gas Maytag centennial) and open the front port to look at the ignitor coil. It never turned orange so I knew there must be a problem with the primary circuit. I shut off the dryer, disconnected the power, pulled it away from the wall, shutoff the gas, and removed the back panel. I then disconnected the wires for the thermal fuse and checked its resistance with a multimeter.... Read more

• Pumps but will not spin
• Will not agitate
• Burning smell
• Touchpad does not respond

My whirlpool washer was no longer spinning, so my first stop was YouTube where I found the video from AppliancePartsPros showing how to replace the motor coupling. In addition to the replacement guide, Matt also shows you how to diagnose the problem by looking for rubber shavings under the washer. Seeing the rubber shavings under the washer, combined with the fact that the washer still drained meant that the motor was still working, so something else in the drive train was bad. I took the... Read more

After looking up the model number of my washing machine on AppliancePartsPros.com I ordered the suspension rod kit, two sets of tub centering springs (one spring per corner), a Ring-Tub (mine was breaking apart due to banging around) and a spare suspension bearing kit in case I need it later. I spoke to a very helpful customer service rep on the phone just before placing my order. They have customer service representatives answering the phone late at night. I was surprised. All of my parts were... Read more

The dishwasher is 4 years old, so I figured since it was leaking from the bottom, replacing the Tub Gasket PN: AP5690109, Splash Shield Kit PN: AP4338941 , and the bottom Door Seal/Gasket PN: AP5809675 was a good idea; the machine probably has around 1200 cycles in 4 years. There's no telling how much the door had opened and closed!? The bottom Door Seal/Gasket was badly worn, and the entire job took me around 30 minutes which included the detailed cleaning of the mating flanges. Take your... Read more

The bar retainers just snapped in and the door handle can be replaced with three screws. Took about 5 minutes total. Read more

Maybe 6 or 7 years ago I had a fridge conk out on me just before Christmas. It was loaded with food for the holiday, including a prime rib roast that was the hope and dream of the holiday for every red-blooded non-vegan in the house. In order to save the day I bottom-dollared a Frigidaire replacement. It performs well temperature-wise, but when it was only a couple years old the door handle cracked wide open. It was so delicate, you'd think that it was a movie prop "Break-Away Refrigerator... Read more

• Will not tumble
• Takes too long to dry

I am very glad to find the AppliancePartsPros.com website! Their instructional videos and easy parts reference made all the difference. I had originally planned to have someone come to fix my dryer, but no one was available for at least a week. I checked out their site, and after watching the videos I felt confident I could repair my appliance. I determined that a drum roller wheel had gone bad. Apparently it was going bad over the last five years since the dryer always seemed to rattle a... Read more

I replaced the belt, belt tension pulley, both dryer drum roller axles and both drum support rollers. Although I bought 2 tumbler bearing kits, because those still look good I am saving them for when they go bad. The videos were fantastic! I also took pictures as I went of wiring so there would be no question where things went when reassembling. It should be noted some models have extra terminals near the sensor terminals... just be aware and look closely/take pics as you are taking things... Read more

This door gasket presses into slot around door pull off old and press in new a five minute repair Read more

• Ice maker dispenses too little ice
• Ice maker not making ice
• Ice maker won't dispense ice
• Leaking

My first hour: I investigated first by pulling out refridgerator to see if the water line hose was kinked. I started under the kitchen sink where it begins, coming from faucet water supply. Then I followed it to the back of the fridge to see if anything looked odd. Next I went to the ice maker itself. I investigated the ice maker by removing the freezer food sliding tray and hanging tray, and then unscrewing the door off the slides. When I looked inside at the ice maker, I saw the tube where... Read more

Upon receiving replacement rails snapped them in place and job was done. Couldn't have been any easier. Read more

I watched a video on YouTube that showed my exact problem. It had a link to this part AP5665171 Hub and it showed how to fix it. It was a fairly simple fix. I did not even have to remove the tub. I popped the cap on top of the agitator plate (AGP), removed the bolt hold the AGP on. I tapped on the bolt several time to loosen it. Using an angled screw driver, carefully and slowly lifted up the edges of the AGP until I could use my fingers to carefully pull the AGP off the splined drive... Read more

• Too hot
• Shuts off too soon

I am not an electrician, just a housewife with limited funds and a desire to DIY. I used the provided videos for knowing how to replace everything except the heating element which I just guessed based on other reviews and seeing how the other parts worked. Our dryer is 11 years old Whirlpool Gold HE and I have only ever cleaned the lint tray. My husband replaced the belt about five years ago and he did clean out the inside of the dryer. Started by ordering a thermal fuse because it was... Read more

My discharge would not empty after a wash cycle and I always had gross gray water left in the bottom approx 3" deep? After doing the obvious things of checking the simp for garbage, and checking that the discharge hose wasn't blocked, I removed my discharge pump ( not too hard to do) and tested. My pump which did run and turn the impeller. However, the pump evidently had weakened with time and weakened and could no longer pump the waste water up hill to the "T" connection under the sink. A... Read more

Well, I got online and found several YouTube videos on how to check what was happening. I have a multimeter and tools. I first replaced the external water filter just to make sure it wasn't that, and it needed it. That wasn't the problem. I then removed the water inlet valve which was really easy. I didn't disconnect the water lines but I did unplug the power plug. Using the ohms setting on the meter, I tested the coil of the valve solenoid. It wasn't open. I checked the voltage at the plug... Read more