Need Help?
Call
Plastic bearing that mounts to the wash tub and supports smooth lid movement. Replace if cracked, worn, or missing to restore proper lid operation.
Watched a YouTube video. Read more
If your washer won't start or the lid won't unlock, the lid lock switch may have failed. This DIY repair typically takes 10-15 minutes with basic tools.
1) Ordered part. 2) Removed front panel by loosening the two screws at the bottom front. 3) Removed old Safety Switch/Lid Lock by disconnecting wires (plug and 2 female disconnects) 4) Reconnected all wires and reinstalled switch. 5) Replaced front panel. 6) Tested Unit. 7) FYI - I found that the locking mechanism stays locked until cycle completely finishes on its own. DO NOT force the cycle to end. Lid will NOT unlock. Read more
This is a water inlet valve with a built-in thermistor that controls the flow of water into the washing machine while monitoring water temperature. The valve opens and closes electronically to fill the tub with the correct amount of hot and cold water based on the selected cycle. Replace this part if the washer is not filling with water, filling slowly, not stopping the fill, or if the water temperature is incorrect during wash cycles.
Purchased replacement fill valve. Read more
White decorative bezel that covers the lid lock mechanism on top of your washer. Replace if cracked, scratched, discolored, or missing from wear.
The lid hinge bearing is used for the lid hinges on washers and dryers. When functioning properly, it allows the lid to open and close properly. If this is a problem with the bearing, it could make the lid difficult to move. In some cases, when the lid will not close, it means that the machine will not function correctly. Damaged lid hinge bearings should be replaced as soon as possible.The lid hinge bearings see a lot of work since they are in use whenever the lid of the washer or dryer opens and closes. They could become cracked and broken over time. Replacing the bearings is a relatively simple repair that owners can make on their own.This lid hinge bearing is for use with many models of washers and dryers from Whirlpool, KitchenAid, Roper, Estate, Inglis, Maytag, Admiral, Amana, Crosley, and Magic Chef. This is a genuine OEM replacement part that has been sourced from the manufacturer. The piece is sold individually, so if owners need to replace more than one hinge, they will need to buy multiples.
With the parts supplied from your company. The lady that took my order was good at her job. All the parts were correct and fit. I thank you for the service that recieved. Read more
Washer won't stop spinning smoothly or makes loud jerking noise when stopping? The brake shoe stops the tub during spin cycles. DIY repair in 1-2 hours.
First I looked at the many you tube vids, and there are many. appliance parts pros pretty much shows you how to deal with the parts. I changed the brake shoes and the clutch assembly which also comes with the driver cam. I also changed the metal brake operating cam. I think that brake lockup or improper brake release was the problem that broke the plastic cam driver. This was the broken plastic part making all the ticking noise. I first changed the coupling on the motor but that wasn't bad. in... Read more
Prevents leaks and seals your washer door during wash cycles. Replace if torn, moldy, or causing water leakage. Verify fit with your model number.
I replaced the door boot with a new one from AppliancePartsPros.com. The most difficult part was starting at the back end of the new boot onto the stationary rim, just in front of the tub. And then anchoring it in place with the existing spring from the previous boot. To start the boot I had to hook the top edge of the boot, where the arrow tab is, onto the rectangular projection on the tub rim and then roll the rubber boot edge down around the tub rim and hope the rim was going into the... Read more
Rear access cover panel for refrigerators. Shields compressor and electrical components from dust and debris. Replace if cracked, damaged, or worn.
My 16 year old son ordered the part and replaced the part. It took him less than 5 minutes to replace the part. Read more
This is a metal hinge support plate that reinforces the door hinge area on a dryer, helping to secure the hinge to the front panel or door. It distributes the stress of repeated door openings across a wider area to prevent damage. Replace this plate if the dryer door sags, feels loose at the hinge, or if the mounting area around the hinge shows signs of cracking or wear.
Replaced several hinge parts. Read more
Inner door frame for front load washers. Provides structural support for door glass and components. Replace if cracked, broken, or damaged from impact.
My teenaged son took the old washer door off and apart. He replaced our glass from our washer onto the new doors and attached it to the hinge. These doors are compatible with Kenmore washer even though it says Frigidaire. Read more
Replacement water fill hoses for washing machines. Connect home water supply to washer. Replace when cracked, leaking, or showing rubber wear or corrosion.
Motor control board was flashing 4 times, indicating that the mode shifter had an error. I disconnected the mode shifter's wire from the controller and measured the resistance between the 2 leads with an ohmmeter. Since the reading was infinite, that meant that the mode shifter coil or in-line thermal sensor was electrically open, i.e. bad. As this fix is near a complete tear-down of the washing machine, here are a few tips I discovered. 1) the hub nut is difficult to remove and you need a... Read more
Size: 5 foot long. Rubber fill hose used on most automatic washing machines. Two hoses used per machine.
Replaced flow meter and control valve Read more
Broken agitator fins or loose upper agitator? This complete assembly restores proper wash action. DIY-friendly 5-10 minute repair with our video guide.
By watching your video and following the instructions Read more
Internal drain hose that connects the washer tub to the drain pump. Replace if cracked, blocked, worn, or causing odors from debris buildup or seal failure.
I replaced the drain pump and hose which had a flapper valve that wasn’t sealing properly. Easy repair. Took about 15 minutes total and my washing machine is Soooo much quieter!!! Read more
This door switch senses whether the appliance door is closed and signals the controls to run only when it's safe. Replacing a worn or intermittent switch restores dependable starts and proper shutoff when the door opens. What it does:
Fix loud grinding noise or basket won't spin issues. This washer transmission gearcase drives the agitator and basket rotation. Moderate DIY repair.
Symptoms: Machine was spinning and spitting a dark colored oil in a circular pattern on the floor under the machine. No strange noises, just messy. Researched issue, Gear-case bad, seal deteriorated and not preventing water from entering gear-case. The additional cam, belt etc I had replaced due to the amount of oil and transmission residue attached to them. Ordered parts, EVERYTHING parts-wise that is needed is included in gear-case package. **NOTE: You WILL need to get a whirlpool spanner... Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.