Your privacy choices: We and our partners use cookies for analytics and ads. Decline all turns them off.
Privacy Policy · Do Not Sell or Share My Personal Information
Need Help?
Call
Broken agitator fins or loose upper agitator? This complete assembly restores proper wash action. DIY-friendly 5-10 minute repair with our video guide.
By watching your video and following the instructions Read more
Washer thrust ring acts as a bearing spacer between the outer tub and basket drive, controlling end-play and reducing friction. Replace when worn to restore smooth, quiet operation and prevent premature wear.
Purchased parts from your site and did a self repair. Excellent quality , speedy delivery and easy to install. Now our 13 year old washer works as good as new. Read more
Washer door boot seal creates a watertight barrier between door and drum. Replace if torn, moldy, or leaking during cycles. Verify fit with your model.
Replaced with new bellows from appliance parts pros. Read more
Interior door frame that holds the window glass and mounting points. Replace if cracked, warped, or broken to restore proper door alignment and latching.
New door hinge &inside &outside door rims new inside &outside door flanges &hinge take pictures of the door inside &out before taking it apart Read more
Fix a washer that fills but won't spin or agitate. This motor start capacitor stores electrical energy to help start your washer motor. DIY repair.
I was actually getting an error code for the shifter and speed sensor. I ordered a shifter, which included the speed sensor, and replaced that part but the washer still didn't work. After doing some more research online, someone mentioned that the capacitor may be bad. After talking to my dad, who is an electrician, he said it sounded like my problem could very well be the capacitor. Knowing that we'd been without a washer for almost two weeks at this point, I went ahead and ordered the... Read more
Rubber grommet for motor mount stud.
Replaced dog ears. Read more
This door switch senses whether the appliance door is closed and signals the controls to run only when it's safe. Replacing a worn or intermittent switch restores dependable starts and proper shutoff when the door opens. What it does:
This lower wire harness routes power and signals between the control and the components beneath the tub on select 4.7/4.8-cu ft top-load washers. Replacing a damaged harness restores reliable connections and helps resolve intermittent motor or pump operation. What it does:
Connects the detergent dispenser to the wash tub in your washer. Replace if cracked, leaking, or causing water damage to other components during cycles.
First of all, I want to say that this is not the first time that I have used AppliancePartsPros. They give you everything you need in the most simplified manner to repair your appliances at home. I ran my washer until I started to see the leak coming from underneath. After verifying that the intake hoses, drain hose and pump were not leaking, I opened up the washer from the top by unscrewing the two screws on the back brackets and lifting up and out. Because the leak was displaying at the... Read more
Adjustable leveling leg threads into the washer base to support and stabilize the unit. Replace if cracked, stripped, or missing to level cabinet.
Fix a washer that won't drain or makes buzzing sounds during drain cycle. This pump assembly removes water from the tub. DIY-friendly repair restores draining.
Replaced Drain pump. Read more
Replacement water fill hoses for washing machines. Connect home water supply to washer. Replace when cracked, leaking, or showing rubber wear or corrosion.
Motor control board was flashing 4 times, indicating that the mode shifter had an error. I disconnected the mode shifter's wire from the controller and measured the resistance between the 2 leads with an ohmmeter. Since the reading was infinite, that meant that the mode shifter coil or in-line thermal sensor was electrically open, i.e. bad. As this fix is near a complete tear-down of the washing machine, here are a few tips I discovered. 1) the hub nut is difficult to remove and you need a... Read more
Adjustable leveling leg that screws into the washer cabinet to stabilize and level your appliance. Replace if broken, damaged, or missing to prevent rocking.
After watching YouTube videos on possible cause, went to appliancepartspros and order seal and leveling legs since the had been missing since machne was given to us. Parts came in within the week and replaced . No more leaks!! Read more
Washer motor won't start or stops mid-cycle? This motor start capacitor stores electrical energy to start your washer motor. Moderate DIY repair.
I found your site which was most helpful. I saw on your forum, that others had replaced a motor & capacitor with + results. I was willing to spend what I thought was a reasonable amount & your guarantee was the clincher. I knew that if I called the appliance store where we had purchased the washer in 1998, it would be very expensive & even more important, it would take many days as they would have to order the part & then schedule a service call. I installed the motor & capacitor & was... Read more
Leaking from the water inlet connection? This vacuum break prevents backflow and maintains the air gap at the inlet. Easy DIY fix in under 30 minutes.
Removed cover from Whirlpool washer (~20 years old) and found water to be leaking from hose connection at Break Vac. Obviously the hose had to be replaced but the Break Vac looked corroded and partially plugged, too, possibly inhibiting water flow. While the cabinet was off I noticed the Suspension Spring was rusted off so I ordered 1 of those, too. Total of all parts was under $45 so looks like we won't be getting a newer, more efficient washer anytime soon. Everything arrived in 3 days and... Read more
Sump hose connects the washer tub to the drain pump. Replace if cracked, leaking, deteriorated, or has holes causing water leaks during wash cycles.
I changed the pump and also discovered the coin trap was wearing thin because it was rubbing against the sheet metal. So I replaced that as well. It took about 15 minutes to remove the coin trap and pump and about 20 minutes to install. The shipping was amazingly fast. I received the parts the next morning. I'm talking I ordered the parts before noon, chose the "fast shipping" option and received parts the next morning around 8:30 AM. Read more
Opt-Out Request Honored
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.