Your privacy choices: We and our partners use cookies for analytics and ads. Decline all turns them off.
Privacy Policy · Do Not Sell or Share My Personal Information
Need Help?
Call
Adjustable leveling foot that supports and stabilizes your refrigerator. Replace if worn, broken, or missing to eliminate wobbling and vibration.
The bracket that held the leveler was stripped. Replaced it and while I was at it, replaced the leveler, too. Read more
Shield cap for laundry center washers. Covers and protects internal components. Replace if cracked, broken, or missing to maintain proper enclosure.
Noise filter (line filter) that suppresses electrical interference on the washer power line. Protects electronic controls from power surges and reduces EMI. Replace if washer has intermittent operation or won't start.
Popped the back control panel and checked where the power comes in. Had power. On the other side of that component there was no power. Found the problem. The hardest part was finding where they hid the model number. Up and under the back of the lid. Nice hiding place. Read more
Washer won't spin or agitate? A failed drive motor is often the cause. This motor assembly restores drum rotation and agitation for reliable washing.
Plastic door cover
Removed from dryer with screwdriver and opened door to access outer glass panel. Replaced with new one and reassambled. Read more
Connects washer drain hose to extension hose. Includes coupling and clamps. Replace if cracked, broken, or when extending drain hose length to reach pipe.
I ordered the drain extension kit and the hose connector kit. Read more
Dryer stops early on auto cycle but works on timed? The moisture sensor control board monitors dryness levels. DIY-friendly repair, 15-20 minutes.
Did some research via the internet and figured the problem was likely the moisture control board. Watched a video of the repair of a similar unit in order to locate the moisture control board. Used the chat feature with one of the Appliance Parts Pros to get a schematic of the dryer and advice about where to use the putty knife to release the springs for access to the board. Thanks to the lady I chatted with for expert advice. Once the actual task was started, the repair took 15 or 20... Read more
Size: 8 foot long. This external washer drain hose is needed when there is more distance between the washer and the drain. Note: comes with 1.5" diameter clamp but hose is 1.25" in diameter; therefore you may need to order the 1.25" diameter clamp separately: WP356138
Just took off the old vacuum break and put the new one on. It was very easy because the site had a video showing how and I watched it first. Read more
This water valve kit regulates the flow of hot and cold water into your appliance during fill. Replace a weak, leaking, or stuck valve to restore consistent fills and proper shutoff, resolving common no-fill, slow-fill, or seeping issues.
Removed old water valve and replaced it with new one. Reconnected wiring and water lines. Everything is working fine now. Read more
Fix washer overflowing or not stopping fill cycle. This water level pressure switch senses tub water and signals control to stop filling. DIY repair.
Filled tub to about 6 inches and inspected washer. Noticed that the tube leading from the air entrapment bubble on the exterior side of the drum had a small leak in it. Clipped off the part of the tube that had the hole in it(it was very close to the connector nipple) reconnected and problem was solved. Read more
This adjustable buzzer kit replaces a failed or noisy mini buzzer to restore audible alerts for cycles, timers and notifications. Compact design lets the appliance signal you reliably when cycles finish or need attention. What it does:
I was looking for a parts sight and found yours. I started to watch all the video tutorials on each part and the "check these connections first video". Well by doing this I was able to find the source of my problem. What I thought was the heating coil not working right, ended up being the timer that was bad!!! I am so very happy with your sight and the step by step videos that were the success to being able to do this on my own. Read more
Replaces cracked, broken, or missing drum baffle that lifts and tumbles laundry inside your washer. Prevents fabric snags and restores proper movement.
Three new vanes. Installation was easy, removed one stainless screw on each vane, slid the broken vanes toward the front of the machine, compressed the old vane slightly and came right out. They have to be slid about 1 to 2 inches forward for removal. This was an easy fix. Read more
Washer won't start, shows error codes, or cycles incorrectly? The control board manages all wash cycles and safety functions. Moderate DIY repair.
After taking the top off the washer I found the Tech Data Sheet ( for repair person ) The E53 code was listed as Low Voltage to the motor board and referred me to test #15. Which stated to check the "drum water NTC" ( Negative Temperature Coefficient or Thermistor). What was misleading was that there are 2 NTC's. If your washer has a "Sanitize" feature , then there is a drum water NTC as well as one on the fill valve body. IF you have the sanitize feature then you need to replace the drum water... Read more
This is a push button switch used to start and stop the wash cycle on a washing machine. It mounts on the control panel and engages the machine's control circuit when pressed. Replace this button if it feels loose, does not click properly, or the washer fails to start or stop when pressed.
Replaced the rubber button. Read more
21-inch drain hose extension for washers. Extends existing drain hose when original is too short to reach standpipe. Includes clamp for secure fit.
Ordered a new drain hose and extension part. The prices including shipping were more reasonable than driving back and forth to the store just to piece meal parts together. Very frustrating. I ordered the parts that were specific to our washing machine, it took maybe 5 minutes to install, and everything fit perfectly. Now we're washing again and no leaks! Read more
This is a small tube of silicone-based gasket sealer used to bond and seal gaskets during washer repairs. It creates a watertight seal between mating surfaces to prevent leaks around tub components or pump housings. Use this adhesive when replacing gaskets or resealing joints where the original sealant has deteriorated and water is leaking.
Opt-Out Request Honored
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.