Crosley Washer Parts

Fix washer overflowing or not stopping fill cycle. This water level pressure switch senses tub water and signals control to stop filling. DIY repair.

21-inch drain hose extension for washers. Extends existing drain hose when original is too short to reach standpipe. Includes clamp for secure fit.

This adjustable buzzer kit replaces a failed or noisy mini buzzer to restore audible alerts for cycles, timers and notifications. Compact design lets the appliance signal you reliably when cycles finish or need attention. What it does:

• Produces audible tones for cycle end, timers and other appliance notifications
• Replaces buzzers that are silent, intermittent, weak or emitting erratic beeps
• Helps you hear and identify completed cycles and timed alerts
• Small, mountable unit that fits behind the control panel and connects to the control board

• One adjustable buzzer kit

• Disconnect power before servicing to avoid shock risk
• Access may require removing the control panel; keep fasteners organized for reassembly
• Disconnect the buzzer wiring harness or connector before removing the old unit; connect the new buzzer the same way
• Test buzzer function with power restored before fully reassembling

Washer won't start, shows error codes, or cycles incorrectly? The control board manages all wash cycles and safety functions. Moderate DIY repair.

This is a small tube of silicone-based gasket sealer used to bond and seal gaskets during washer repairs. It creates a watertight seal between mating surfaces to prevent leaks around tub components or pump housings. Use this adhesive when replacing gaskets or resealing joints where the original sealant has deteriorated and water is leaking.

Fix unresponsive or erratic cycle selection with this rotary encoder switch. Mounts behind the control knob to restore accurate cycle settings and indicators.

Washer making noise or experiencing weak water circulation? This impeller cap secures the wash pump impeller for proper water flow and performance.

Replacement drain hose for washers. Routes wastewater from the drain pump to your household drain. Replace if cracked, leaking, clogged, or worn.

Replacement power cord for laundry centers and washers. Installs at the rear panel to restore electrical connection. Needed when original cord is damaged, frayed, or missing.

Includes suspension pads.

A hinge pin assembly that secures and aligns an appliance door to its cabinet, restoring proper fit and smooth opening and closing while reducing hinge noise. What it does:

• Secures the door pivot and maintains proper door alignment for a consistent seal.
• Can correct door sag, uneven gaps, or doors that stick, scrape, or fail to close fully.
• Can reduce grinding, clicking, or binding noises caused by worn or bent hinge pins.
• Replaces worn, broken, or bent hinge components that affect door motion.

• Disconnect power to the appliance before beginning any repair.
• Support the door (use a helper or suitable block) to prevent it from dropping when removing the hinge.
• Basic hand tools are typically required; follow the manufacturer's service instructions for safe removal and reinstallation.
• Inspect adjacent hinge mounts and fasteners during installation; replace damaged mounting hardware as needed.

Silicone lubricant conditions rubber seals and O-rings in appliances. Apply during service to ease installation and prevent leaks. Confirm fit by model.

This replacement vent manages internal airflow within your appliance, routing air through the intended path. Restoring a damaged or missing vent helps maintain performance and reduces heat and moisture buildup inside the cabinet. What it does:

• Directs and regulates airflow through the appliance's air path
• Helps maintain proper pressure balance and efficient moisture removal
• Reduces the chance of lint or debris bypassing the intended ducting
• A cracked, warped, missing, or clogged vent can contribute to weak airflow, longer cycles, excess heat, or unusual noises

• 1 vent

• Disconnect power before servicing; allow hot components to cool
• Access the vent by removing the appropriate panel; note screw and clip locations
• Transfer any mounting hardware or seals from the old vent and ensure proper orientation
• Clear lint/debris from adjoining ducts before reassembly; test run to ensure smooth airflow and no rattling

Carries water from home supply to washer inlet valve. Replace if your hose is cracked, worn, leaking, or damaged by pests or age. Restores proper fill.

This knob assembly replaces the "modifier" control knob on the console so you can adjust settings smoothly and reliably again. Restore a secure, positive-turn feel when the original knob is cracked, stripped, or missing.

• Attaches to the control shaft to select and adjust options/settings
• Replaces knobs that are cracked, broken, or missing
• Fixes a knob that spins freely, slips, or won't turn the control
• Restores proper selection and tactile feedback during use

• Disconnect power to the appliance before servicing
• Pull the old knob straight off the shaft; avoid prying against the panel
• Align the flat/splines on the new knob with the shaft and press on firmly until fully seated
• The pointer aligns with the panel markings before use

Color: Gray. Size: 13 oz. can. Used for coating the dryer drum interior. Acrylic appliance paint.