Crosley Washer Parts

• Leaking

Fixed by replacing the washer door seal "Bellows". Once again AppliancePartsPros comes through with the right part at a great price. It took quite some time to install because putting the inside spring back on the bellow was difficult so I needed to remove the top and front door of the washer to get better access. A set of 3 or 4 plumbing clamps are highly recommended to get that spring back on (I went to the store and bought some). If you search YouTube about replacing the bellows on your... Read more

• Spins slowly
• Will not agitate
• Pumps but will not spin

My parents have the older 80 series washer and dryer that gets used way more than a consumer washer and dryer was ever meant to be used. The washing machine finally said im tired. During the spin cycle it was making a really loud squealing noise and during the agitation cycle it would barely agitate the clothes. So i ordered the basket drive to get rid of the squealing during spin cycle and noticed the dogs on the cams were warn and werent grabbing so ordered the whole cam kit to be safe... Read more

Replaced internal drain hose. and while I was in there I changed some known wear items. water pump,direct drive coupling tub to pump hose and a spring Read more

I took the door assembly apart by removing the 7 screws on the inner door and the 2 on the striker. I removed the hinge from the washer so that I could place it inside the door when I put it back together. This is much easier then trying to reassemble the door while the hinge is attached to the machine. Once I lined up all of the pieces properly, I screwed it back together and remounted the striker. I then put the entire door back on the machine by screwing in the three screws that hold on... Read more

Took off cover, installed new parts. Read more

• No hot or cold water
• Will not stop filling with water

It was really easy to fix. I just took a screw driver and gently pried up on the top of the clothes washer to open up the top. Then the mixing valve was easy to access. I removed the two screws holding and unplugged the the wires. And pulled the old one free. Then reversed the process to install the old one. Less than thirty minutes start to finish. Read more

In reality, this turned into a full-on rebuild project - with several parts orders, not just a simple repair. But I have to give credit: The parts listings with pictures on the AppliancePartsPros web site were really useful in figuring out what was going on inside the machine, and what parts I would need. Also: The repair videos were critical for me to be able to ensure I was reassembling everything correctly. Shout out to Simon, who was featured in several of the repair videos. His "gorgeous... Read more

This repair was performed on a Whirlpool Cabrio clothes washer Model # WTW5640XW0 which has the digital electronic controls rather than the older style timer, electro/mechanical controls. This washer was made in 2010. Simply having the diagnostic programs on this machine is wonderful and they work remarkably well and led me to the shifter/rpm sensor component straight away. It was a simple replacement by tipping the washer onto its front and accessing through the bottom. The machine was put... Read more

I started with the suspension pad kit and the tub suspension pads. I do have to say if you have an older model washer (mine is approx 17 years old) be prepared to let the inner tub sit in penetrating oil for a few days before attempting to take the tub out. I was able to get to this point on my own and then it wouldn't budge. My husband ended up buying some direct drive tool (it was pretty cool) and was able to break the tub free after two days. Yay! From there he took the the inner tub and put... Read more

Installed new pump Read more

Rebalanced the load but noticed the drum was sitting lower and the springs were wore out and it went out of balance easy, so i got the suspension rod kit and installed it and it works much better. It took me 2 hours because i didnt have adequate room to move around. Hour job if you have room. Read more

• Won't start

Not knowing for sure that the problem was the capacitor, I was reluctant to purchase and replace the part. I went AppliancePartPros.com web site and clicked on the part replacement video.The repair video was short and well illustrated. Before the repair began, the service rep says, " the reason you would replace the capacitor is that after turning the timer on, the machine would just hum." The instruction video was the reason that I purchased the part at AppliancePartPros.com The part was... Read more

Replaced Snubber Ring installed spring kit. Watched installation video, found it very helpful to plan repair. The washer runs like new now. Read more

• Door won't close

I chatted with a rep on Appliance Parts Pros and found out which parts I needed for my model of dryer. Ordered the 2 clips that held the door closed. They arrived the next day!! My dryer was very different than the video but we were able to figure out which screws to remove. The old clips popped out and the new ones popped in. Took about 30 minutes because of there being a top and bottom clip to remove and replace and line up the door parts to screw the screws back in. It works great!! I... Read more

My wife and I along with Mat on the video replaced the upper and lower friction pads, along with the balance springs. The machine runs smooth as it did new. Thank you everyone at Appliance Parts Pro and Mat. You are a great company. P.S. my wife and I should had made our own video for you since we are both in our 60s I bet it would have been funny Thanks Again. JIm & Debbie from Texas. Read more

Replaced pump. All components are accessible from the front of the machine. You have to remove two screws in the back that hold on the top cover, then slide the cover back. This will allow access to the screws that hold on the control panel. Remove the control panel (unplug cable), then remove the spring/wire that holds on the door bellows to the front panel (removing and installing that is the most difficult part of the job) and carefully remove the bellows from the front panel. Then remove... Read more