Dryer Burner & Related Parts

This replacement coil controls the gas valve's opening and holding action during burner operation. Replacing a weak or failed coil restores reliable ignition and steady heat for consistent drying performance. What it does:

• Powers the valve to open during ignition (booster) and keeps it open while heating (holding)
• Helps resolve: igniter glows but no flame, burner lights then shuts off, no heat, intermittent heat/long dry times
• Restores proper gas flow for consistent temperatures
• Direct-fit electrical connection for the valve solenoid

• 1 booster & holding coil

• Disconnect power and shut off gas supply before servicing
• Allow the burner assembly to cool; access the gas valve compartment
• Label and disconnect wires; replace the coil in the same orientation; secure clips/brackets
• Restore gas, check for leaks with an approved solution, then test burner operation

This kit includes the components needed to convert a natural gas dryer to operate on liquid propane (LP) gas. It typically contains replacement orifices and related hardware sized for LP gas pressure. Use this kit when switching your dryer's fuel source from natural gas to propane, such as when moving to a home without a natural gas supply.

Fix a dryer that won't heat or cycles but doesn't ignite with this gas burner assembly. Restores consistent flame when the original is corroded or clogged.

Dryer won't heat or gas won't ignite? This gas valve controls gas flow to the burner assembly. Moderate DIY repair requiring drum removal.

Dryer won't heat or flames are yellow? This butane burner orifice meters gas flow for clean, reliable ignition. Required for butane conversions.

This conversion kit includes the orifices and components needed to convert a natural gas dryer to operate on liquid propane (LP) gas. It ensures the correct fuel-to-air mixture for safe and efficient burner operation on LP. Use this kit when installing a natural gas dryer in a home that only has an LP gas supply.

Fix a dryer that won't heat or has a weak flame with this gas burner orifice. Controls proper fuel flow for consistent heating. Direct replacement part.

This assembly includes the gas valve and connecting pipe that control the flow of gas to the dryer's burner. It regulates when gas is delivered to the igniter and burner tube during the heating cycle. Replace this assembly if your gas dryer is not heating, heats intermittently, or if the gas valve fails to open properly during operation.

The Water Valve is an OEM part for GE electric dryers. Located near the bottom of the machine, it controls water flow into the condenser system during moisture-sensing cycles.

The moisture sensing function uses this valve to introduce precise amounts of water vapor into the exhaust air stream periodically. This allows the condenser to capture moisture readings accurately and determine optimal cycle time based on humidity levels. 

Causes of failure include mineral buildup restricting flow, worn seals enabling leaks, or misaligned internal components hindering valve movement.

Symptoms of a faulty water valve are: 

• Loss of moisture sensing ability
• Incomplete or improper readings affecting cycle times  
• Water leaks from the valve area
• Failure to inject water vapor as needed

This part is also compatible with some Kenmore models using GE components.

This Pipe Assembly routes water into the appliance so the dispenser and ice maker can receive a steady supply. Replacing a damaged tube restores proper water flow and helps stop leaks or pooling inside or beneath the unit. What it does:

• Carries incoming water from the household supply to the appliance's internal water system
• Restores water delivery to the dispenser and ice maker when the original tube is cracked or blocked
• Prevents leaks and water damage caused by split, corroded, or pinched tubing
• Helps eliminate intermittent flow or weak dispenser output caused by a damaged water line

• One complete pipe assembly as shown

• Shut off the refrigerator's water supply and unplug the appliance before beginning
• Handle tubing fittings carefully; use proper tools to avoid damage or overtightening
• Inspect connection points and replace seals or clips if worn; test for leaks after reinstalling

The dryer gas connector kit contains the wiring connectors used to link the gas ignition and heating components inside your dryer. It ensures a reliable electrical connection between the igniter, gas valve coils, and the control system. Replace this kit if your dryer runs but won't heat, the igniter fails to glow, or you have a damaged or melted connector causing an intermittent heating problem.

Fix a dryer that won't heat with this gas valve. Controls gas flow to the burner assembly. Moderate difficulty repair taking 30-45 minutes.

Dryer not heating or won't ignite? This gas valve and pipe assembly controls propane flow to the burner. Common fix for no-heat issues on gas dryers.

Converting dryer from LP to natural gas? This gas orifice regulates gas flow to the burner for proper heating. DIY-friendly swap, takes 20 minutes.

Converting your dryer from LP propane to natural gas? This conversion kit includes the orifice and components needed for a quick, straightforward swap.

Fix buzzing noises or no flame in your gas dryer with a new valve assembly. Solves igniter glow without ignition. Moderate DIY repair with basic tools.