Estate Parts

My 16 year old son ordered the part and replaced the part. It took him less than 5 minutes to replace the part. Read more

Looked up parts on internet using diagrams, ordered parts, they arrived in 2 days and installed them. Read more

• Noisy

We opened the dryer up with help from the videos on your site, and came to the conclusion that the rear drum-support rollers needed to be replaced. We thought the front bearing and seal looked a little past-it as well, so we ordered that and a new bearing ring to go with it, and a new dryer belt (just so we wouldn't have to get back into it again any time soon). I ordered the parts (standard shipping) at 4:30 PST on Tuesday and they arrived before 3:00 the next day! I replaced the front bearing... Read more

Read directions on how to change the power cord and watched video on your site on how to change the drain hose. Everything went perfectly. Read more

Appeared to be two problems: the latch was worn and one of the pins that slid in a guide on the actuator located in the inner panel had broke off. Detergent lid spring and pin appeared to be OK but decided to replace since I was aready working on it. I ordered all the inner panel mechanism from the control arm to the latch actuator on the inner panel. The repair was successful as the detergent dispenser now opens during its cycle. Read more

When the new bulb didn't want to go in, I felt around and realized the base of the old bulb was still in there. With some effort I got it out and new bulb in, Light cover fit fine, but did not come with a screw to hold it in. That would have been helpful. Read more

After the part arrives, I was double check to make sure I got the right part. Importantly, unplug the electrical power first before do anything, also turn off the water hose for safety. Then removed 4 screw out side panel and 2 screw in side to get lose. After all, replaced a new part and put all panel and screw back together. Finally, plug in electrical power then a water hose and test a new part just installed. So far so good, seem like everything was function OK. Again, thanks for your web... Read more

We were browsing in a store seen this microwave on clearance. So we asked what was the lowest price they could do because it was missing so many parts. They gave us a total which they then deducted off the clearance price. I knew that we could get the same parts from appliance parts pros for less so we bought the microwave and ordered the parts and now I have a $400 microwave for $180.00 including the new parts, got the parts and my new microwave is ready for the holidays. We have used... Read more

Replaced flow meter and control valve Read more

First I watched the repair video, and then was successful in changing out two of the Ignitor's on the surface Burners, it worked great ! Read more

Replaced igniter under oven floor panel. Read more

Troubleshot the oven by checking the broiler which worked good (same fuel valve). After reading the some tips about troubleshooting the Glow Ignitor I could see the broiler ignitor got white hot and the oven ignitor only got bright orange (orange to red causes intermittent ignition or mini explosions). Watched the how to video and it was good information. You should be observant about which openings in the back of the oven as to where the two wires are coming out of. My oven is over 12 years... Read more

Used the vinyl touch up paint on the tops of posts and slid vinyl tips over 130 posts. The paint acts as an adhesive to keep the tips secure. Read more

I nearly shelled out for a new Kitchenaid when I remembered APP and entered my model # just for fun. The interactive diagrams and install videos showed where all the parts "should" be, mine were badly disintegrated, so I replaced the damaged ones and swapped out all of the other easily accessible seals and bearings (also gave it a good and very disturbing cleaning). My parts surprisingly arrived next day and for about $40, the dishwasher is quiet and works like new again. Read more

Motor control board was flashing 4 times, indicating that the mode shifter had an error. I disconnected the mode shifter's wire from the controller and measured the resistance between the 2 leads with an ohmmeter. Since the reading was infinite, that meant that the mode shifter coil or in-line thermal sensor was electrically open, i.e. bad. As this fix is near a complete tear-down of the washing machine, here are a few tips I discovered. 1) the hub nut is difficult to remove and you need a... Read more

I had replaced the Agitator cams a couple of times already due to my brother-in-law overloading the machine which stripped the teeth off of the cams. I also noticed the agitator seemed to 'wobble' and made 'knocking' noises quite a bit. I reviewed the video on the Appliance Parts Pros web site, disassembled the agitator and cleaned everything up, which helped a little, but not enough. Figuring the agitator itself was worn out also, I looked up and ordered all the parts for the upper agitator on... Read more