Frigidaire Door, Door Glass & Parts

The Outside Door Panel replaces a cracked or broken outer trim on your washer door. It restores appearance and alignment, supporting the door glass and handle so the door latches correctly and cycles can start.

• Forms the exterior frame/trim and handle area of the washer door
• Supports and positions the door glass while aligning with the hinge and latch
• Helps ensure the door closes properly to allow a cycle to begin
• Typical symptoms: cracked/broken trim, loose or misaligned door, difficulty opening/closing

• Disconnect power; turn off water supplies before servicing
• Open the door and support the assembly; remove perimeter screws securing the outer to the inner door panel
• Transfer door glass, handle components, and any reusable hardware from the old panel to the new one
• Reassemble and tighten screws evenly; verify smooth operation and proper latching before use

This replacement glass panel restores the viewing window and heat barrier in your oven door. Swap a damaged pane to maintain safe operation, proper heat retention, and a clean, clear view of what's cooking.

• Provides the door's viewing window and helps insulate the oven cavity
• Restores visibility into the oven during baking and broiling
• Replace if the glass is cracked, shattered, scratched, or permanently stained
• Common symptoms include visible damage, heat loss, uneven baking, or exterior door area feeling hotter than normal

• Disconnect power (and shut off gas, if applicable) and allow the appliance to cool completely
• Wear cut-resistant gloves and eye protection; tape over broken glass before removal
• Note pane orientation, spacers, and seals; transfer any hardware in the same positions
• Avoid overtightening fasteners and clean fingerprints from the new glass after installation

This flat replacement glass shelf provides a stable, easy-to-clean surface inside the refrigerator to help organize and protect food. It restores proper shelving where the original glass was cracked, scratched, or missing. What it does:

• Replaces a flat refrigerator shelf glass to support food items and containers
• Restores even storage surfaces and prevents spills from soaking shelves below
• Helps maintain refrigerator interior organization and visibility of contents
• Fits into existing shelf supports or trim rails when the original glass is damaged or removed

• One flat replacement glass shelf

• Handle the glass carefully and wear cut-resistant gloves to avoid injury
• Remove food and any trim/shelf supports before swapping the glass
• Place the new glass into the existing rails or supports; do not force or bend components
• If any clips, rails or seals are damaged, replace them before use to ensure proper fit and safety

This oven door glass assembly replaces damaged or cracked door glass to restore a clear viewing window and help keep the oven cavity sealed. It's a direct-fit replacement for affected Frigidaire oven doors. What it does:

• Replaces cracked, chipped or broken oven door glass to restore safe, visible operation.
• Lets you monitor cooking without opening the door to prevent heat loss from frequent door openings.
• Helps the door maintain its sealed barrier for more consistent oven performance.
• Matches OEM form for straightforward fit and alignment when installed correctly.

• Disconnect power (and gas if applicable) before starting; handle glass with thick gloves and eye protection.
• Installation may require removing the oven door and several screws—keep parts organized and follow OEM instructions.
• Inspect door seals and mounting hardware while replacing the glass; replace any damaged components.

This glass assembly replaces a damaged or broken oven door viewing panel to restore visibility and help contain heat for safe cooking. It fits into the oven door frame and provides a clear window for monitoring food. What it does:

• Replaces cracked, shattered, or scratched oven door glass to restore a clear viewing window
• Helps maintain proper heat containment and oven performance when installed correctly
• Eliminates rattling or movement caused by loose or broken glass
• Reduces risk of cuts or glass fragments inside the oven when replacing damaged glass

• One glass assembly as shown

• Handle with heavy-duty gloves and eye protection; glass can break unexpectedly
• Follow the oven manufacturer's door-disassembly instructions; some installs require removing the door and brackets
• Inspect door seals and mounting hardware and replace any damaged components for a secure fit

This control panel is the front console trim that houses the touchpads and display, restoring a clean, functional user interface for your range or oven. It replaces cracked, faded, or damaged front console surfaces to improve operation and appearance. What it does:

• Provides the outer housing for oven/range controls, buttons, and display
• Restores proper button engagement and protects internal electronics from spills and debris
• Commonly replaced for cracked, warped, or discolored panels or when buttons are loose
• Helps resolve issues where the console face is physically damaged or missing

• Disconnect power (unplug or shut off breaker) before starting any repair
• Remove trim and mounting screws carefully; keep hardware for reinstallation
• Align tabs and clips gently to avoid breaking plastic; do not force parts into place
• Verify secure connections before restoring power

A replacement outer glass door panel kit that restores the refrigerator door's appearance and insulating surface. The white outer panel includes foil tape for sealing and finishing the edge for a clean, factory look. What it does

• Replaces a cracked, chipped, or discolored outer glass door panel to improve appearance.
• Restores the door's exterior surface and helps maintain the door edge seal when used with the included foil tape.
• Helps prevent drafts and moisture intrusion at the door edge when installed correctly.
• Matches the original white finish for a factory-style look.

• Disconnect power to the appliance before starting and remove contents from the door.
• Handle the glass panel carefully; wear gloves and eye protection to reduce cut risk.
• Installation typically requires removing the door trim/retainer and carefully replacing the outer glass; keep fasteners and seals organized.